Toro 145-3530 Manual de usuario
Form No. 3463-130 Rev A
T rimmer Rack
GrandStand
®
Revolution
®
Mower
Model No. 145-3530
Installation Instructions
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
1
No parts required
–
Prepare the machine for installation.
Upper mount bracket 1
Screw (5/16 inch)
3
Slot bracket
1
Carriage bolt (1/4 x 3/4 inch)
2
Nut (1/4 inch)
4
Large st clamp
1
Large backer plate 1
2
Hex-head ange screw (1/4 x 1-1/2
inches)
2
Install the upper bracket assembly .
Lower mount bracket 1
Screw (5/16 inch)
2
Adjustment plate 1
Carriage bolt (1/4 x 3/4 inch)
2
Nut (1/4 inch)
4
Small st clamp
1
Small backer plate
1
3
Hex-head ange screw (1/4 x 1-1/2
inches)
2
Install the lower mount bracket.
4
No parts required
–
Complete the installation.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
Register at www .T oro.com.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
*3463-130*
1
Preparing the Machine
No Parts Required
Procedure
1. Park the machine on a level surface.
2. Disengage the drives and the power take-of f.
3. Shut of f the machine and remove the key .
4. W ait for all moving parts to stop.
5. T urn the battery-disconnect switch to the O FF
position.
6. Lower the platform.
7. Loosen the twist knobs on each side of the
machine.
g375719
Figure 1
1. T wist knob
2. Cushion
8. Lower the cushion to the platform.
9. Remove the rear access cover .
g377627
Figure 2
2
2
Installing the Upper Bracket
Assembly
Parts needed for this procedure:
1 Upper mount bracket
3
Screw (5/16 inch)
1
Slot bracket
2
Carriage bolt (1/4 x 3/4 inch)
4
Nut (1/4 inch)
1
Large st clamp
1 Large backer plate
2
Hex-head ange screw (1/4 x 1-1/2 inches)
Procedure
1. On the left side of the machine, measure and
mark the 3 holes as shown below .
g443616
Figure 3
1. 17.6 cm (6.93 inches) 4. 6.4 cm (2.52 inches)
2. 4.6 cm (1.82 inches) 5. 1 1.4 cm (4.5 inches)
3. 4.1 cm (1.61 inches) 6. 14.5 cm (5.71 inches)
W ARNING
Using a drill without proper eye
protection may allow debris to enter the
eye, causing injury .
When drilling, always wear eye
protection.
2. Use a drill bit (9/32 inch) to drill through the 3
marked hole locations.
Note: When drilling, avoid pushing the drill bit
too far beyond the plate.
3. Use compressed air to remove the metal
shavings from drilling.
4. Use 3 screws (5/16 inch) to secure the upper
mount bracket to the machine.
g441540
Figure 4
1. Screw (5/16 inch)
2. Upper mount bracket
5. Use 2 carriage bolts (1/4 x 3/4 inch) and 2 nuts
(1/4 inch) to secure the slot bracket to the upper
mount bracket.
3
g441543
Figure 5
1. Slot bracket 3. Nut (1/4 inch)
2. Carriage bolt (1/4 x 3/4
inch)
4. Upper mount bracket
6. Use 2 hex-head ange screws (1/4 x 1-1/2
inches) and 2 nuts (1/4 inch) to secure the large
st clamp and large backer plate to the slot
bracket.
g441545
Figure 6
1. Large st clamp 3. Nut (1/4 inch)
2. Large backer plate
4. Hex-head ange screw
(1/4 x 1-1/2 inches)
3
Installing the Lower Mount
Bracket
Parts needed for this procedure:
1 Lower mount bracket
2
Screw (5/16 inch)
1 Adjustment plate
2
Carriage bolt (1/4 x 3/4 inch)
4
Nut (1/4 inch)
1
Small st clamp
1
Small backer plate
2
Hex-head ange screw (1/4 x 1-1/2 inches)
Procedure
1. Using the lower mount bracket as a template,
mark the 2 holes as shown below .
g443617
Figure 7
1. 2.54 cm (1 inch) 3. 17.6 cm (6.93 inches)
2. 2.54 cm (1 inch)
4
W ARNING
Using a drill without proper eye
protection may allow debris to enter the
eye, causing injury .
When drilling, always wear eye
protection.
2. Use a 9/32 inch drill bit to drill through the 2
marked hole locations.
Note: Do not push the drill bit too far past the
plate when drilling.
3. Use 2 screws (5/16 inch) to secure the lower
mount bracket to the machine.
g441547
Figure 8
1. Lower mount bracket
2. Screw (5/16 inch)
4. Use compressed air to remove the metal
shavings from drilling.
5. Use 2 carriage bolts (1/4 x 3/4 inch) and 2 nuts
(1/4 inch) to secure the adjustment plate to the
lower mount bracket.
g441563
Figure 9
1. Lower mount bracket 3. Adjustment plate
2. Carriage bolt (1/4 x 3/4
inch)
4. Nut (1/4 inch)
6. Use 2 hex-head ange screws (1/4 x 1-1/2
inches) and 2 nuts (1/4 inch) to secure the
small backer plate and small st clamp to the
adjustment plate.
g441614
Figure 10
1. Small st clamp 3. Nut (1/4 inch)
2. Small backer plate 4. Hex-head ange screw
(1/4 x 1-1/2 inches)
5
4
Completing the Installation
No Parts Required
Procedure
1. Install the rear access cover .
g377627
Figure 1 1
2. Raise the cushion to the platform.
3. T ighten the twist knobs on each side of the
machine.
g375719
Figure 12
1. T wist knob
2. Cushion
4. Adjust the upper and lower plates to t your
trimmer as needed.
5. T urn the battery-disconnect switch to the O N
position.
Figure 13 illustrates the correct position of the
trimmer on the rack.
Note: Position the upper trimmer handle so that
is held in place by the upper clamp.
g442743
Figure 13
6
Notes:
Tabla de contenidos
Otros manuales de Accesorios para cortadoras de césped de Toro
Toro
Toro 78593 Manual de usuario
Toro
Toro 79318 Manual de usuario
Toro
Toro 04553 Manual de usuario
Toro
Toro 138-6246 Manual de usuario
Toro
Toro Z-Master Manual de usuario
Toro
Toro 144-2688 Manual de usuario
Toro
Toro 108-3160 Manual de usuario
Toro
Toro 130-6020 Manual de usuario
Toro
Toro Super Bagger 20897 Manual de usuario
Toro
Toro 140-5605 Manual de usuario
Toro
Toro Pro Sweep 5200 Manual de usuario
Toro
Toro 22202 Manual de usuario
Toro
Toro Reelmaster 2000 Series Manual de usuario
Toro
Toro 30549 Manual de usuario
Toro
Toro 110-6506 Manual de usuario
Toro
Toro Wheel Horse 78361 Manual de usuario
Toro
Toro 78537 Manual de usuario
Toro
Toro 78534 Manual de usuario
Toro
Toro 136-9045 Manual de usuario
Toro
Toro 03661 Manual de usuario
