Tornatech GT-FluxFP Manual de usuario

GT-FluxFP

Orice Plate Flowmeter

FM Approved

OPERATING INSTRUCTIONS

Tornatech - GT-FluxFP

IMPRINT

of Tornatech Inc. - even partial content - is strictly prohibited.

Subject to change without notice.

2Tornatech - GT-FluxFP

Table of Contents

  ............................................................................................

1.1 Intended use ......................................................................................................................3

 ......................................................................................................................3

1.3 Safety instructions from the manufacturer..............................................................4

  ................................................................................................

2.1 Scope of delivery ..............................................................................................................5

2.2 Nameplate...........................................................................................................................6

 ............................................................ 

3.1 Installation notes ..............................................................................................................7

3.2 Installation instructions..................................................................................................7

3.3 Mode of operation.............................................................................................................9

  .....................................................................................................................

 ........................................................................................................ 

5.1 Dimensions and weights.................................................................................................13

 .................................................................................................... 

  ........................................................................................................................ 

7.1 Storage ................................................................................................................................17

Tornatech - GT-FluxFP

SAFETY INSTRUCTIONS

1 

1.1 Intended use





(in compliance of the directional arrow).

The necessary FM Approval is available.

Warning!

The operator of these measuring devices is solely responsible for the

suitability, intended use and corrosion resistance ofthe selected materials.

It must be particularly ensured that the materials selected for the wetted

parts of the owmeter are suitable for the process media to be measured.

The manufacturer is not liable for any damage resulting from improper or

unintended use of these devices.

The device may only be used in the operating instruction specied pressure

and temperature limits.

1.2 

»FM Approval Class: 1046

4Tornatech - GT-FluxFP

SAFETY INSTRUCTIONS

1.3 

The manufacturer is not liable for damages of any kind caused by the use of the device,

including, but not limited to direct, indirect, incidental, punitive and consequential

damages.

For every product purchased from the manufacturer warranty applies, according to the

relevant product documentation and the valid terms and conditions.

The manufacturer reserves the right to revise the content of the documents, including

this disclaimer, without notice, and is not liable in any way for possible consequences of

such changes.

The responsibility that the instruments are suitable for the particular application rests

solely with the operator. Tornatech Inc. assumes no liability for the consequences of

            

consultation.

In case of a complaint the contested elements must be cleaned of hazardous substances

and to be returned to the manufacturer unless otherwise agree (see 7.3).

To prevent injury to the user or damage to the unit, it is necessary that you reading this

operating instruction carefully before starting using the device.

The instruction is intended for both the correct installation, operation and maintenance

of the equipment.

Special designs for special applications and custom models are not covered by this

documentation.

Tornatech - GT-FluxFP

DEVICE DESCRIPTION

2 

2.1 



Operating instructions



Replacement gaskets (not shown here)

Fig. 1 Scope of delivery

6Tornatech - GT-FluxFP

DEVICE DESCRIPTION

2.2 

Description code / Order code

Nominal size and process connection

Flow range (USGPM)

Flow range (LPM)

Fig. 2 Nameplate bypass meter Turbo-Lux®3

Fig. 3 Nameplate orice plate

Tornatech - GT-FluxFP

INSTALLATIONANDMODEOFOPERATION

3 

3.1 Installation notes

Information!

All instruments are carefully checked for proper function before shipment.

Check immediately on receipt, the outer packing carefully for damage or

signs of improper handling.

Report damage to the carrier and your locale sale sta. In such cases, a

description of the defect, the type and the serial number of the device is

indicated.

Unpack the unit carefully to avoid damage.

Check the completeness of the delivery against the packing list. Check the

name plate, if the delivered ow meter according to your order.

3.2 





the nominal diameter (D).

With an installation of an one quarter pipe (independend of the direction) the distance of





8Tornatech - GT-FluxFP

INSTALLATIONANDMODEOFOPERATION

Fig. 4 Inlet path and outow zone at 5 x D with an one quarter pipe

»-

fore, where at least 5 x D must be available as a straight inlet section directly in front



Fig. 5 Inlet path and outow zone

»An inlet path of 5 x D requires a mounted quarter pipe before.





Tornatech - GT-FluxFP

INSTALLATIONANDMODEOFOPERATION





-

tal position.



the compliance of the measuring tolerance is the central mounting of the pipeline. The



Fig. 6 Examples of installation





-









7.2). The tightening of the nut or the cap should be done by hand as possible. The threads



with water.

3.3 

             

-







Inlet and outlet port for the bypass to be measured are arranged concentrically, so that

an easy to combine with the stationary primary element.

10 Tornatech - GT-FluxFP



4 START-UP



-



Fig. 7 Float

-



surges that could damage the bypass meter.

Reference point

Fig. 8 Rotation bypass meter

When the bypass meter is commissioned or set into operation, bubbles of air will initially



9, pos. 9) must be somewhat loosened during operation and the device must be rotated

by 360°, so that the air bubbles can escape. Then the bypass meter has to be positioned

vertically and the union nut has to be tightened once again.

Before pressure test in pipes, the bypass meter has to be disassembled

and the connection of the orice plate has to be screwed pressure-tight

with the cap.

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario