Torin BIG RED T31002 Manual de usuario
OWNER’S MANUAL
1-TON HYDRAULIC ENGINE CRANE
Item: T31002
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at
1-888-44-TORIN (1-888-448-6746), 8 a.m.- 5 p.m., PST, Monday-Friday.
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure
to follow the safety rules and other basic safety precautions may result in serious personal injury.
Version 20170620
REGISTER
YOUR PRODUCT
http://www.torin-usa.com/
customer-support/
register-a-product.html
SCAN CODE
2
IMPORTANT
OWNER / USER RESPONSIBILITY
INTENDED USE
Before You Begin Register This Product.
For future reference, record the model name, model number, date of manufacture and purchase date of this
product. You can nd this information on the product.
Model Name ________________________
Model Number ________________________
Date of Manufacture _______________________
Date of Purchase ________________________
DO NOT OPERATE OR REPAIR THIS PRODUCT WITHOUT READING THIS MANUAL.
Read and follow the safety instructions. Keep Instructions readily available for operators. Make certain all
operators are properly trained and understand how to safely and correctly operate the product. By proceeding
you agree that you fully understand and comprehend the full contents of this manual. Failure to operate this
product as intended may cause injury or death. The manufacturer is not responsible for any damages or injury
caused by improper use or neglect. Allow product operation only with all parts in place and operating safely.
Use only genuine replacement parts. Service and maintain the product only with authorized or approved
replacement parts; negligence will make the product unsafe for use and will void the warranty. Carefully
inspect the product on a regular basis and perform all maintenance as required. Store these instructions
in a protected dry location. Keep all decals on the product clean and visible. Do not modify and/or use for
any application other than that for which this product was designed. If you have any questions relative to a
particular application, DO NOT use the product until you have rst contacted the distributor or manufacturer to
determine if it can or should be performed on the product.
For technical questions please call 1-888-448-6746.
This Equipment is specially designed to raise, lower and transport engines, differentials,
transmissions, and other heavy loads with minimal effort. Tested for reliability and safety to meet ASME PASE
standards.
3
TECHNICAL SPECIFICATIONS
T31002
P1 25T
P2 0.5T
P3 0.75T
P4 1T
A 1364mm 53-11/16"
B 1457mm 57-3/8"
C 145mm 5-11/16"
D 1180mm 46-7/16"
E 780mm 30-11/16"
L1 890mm 35-1/16"
L2 980mm 38-9/16"
L3 1070mm 42-1/8"
L4 1160mm 45-11/16"
H1 2018mm 79-7/16"
H2 2250mm 88-9/16"
L4
P4 P3 P2 P1
A
C
H1
H2
L3
L2
L1
B
D
E
4
SAFETY MARKINGS
SAFETY
Always use Jack Stands!
Always follow safety precautions when installing and operating this equipment. Keep all decals on the unit
clean and visible. Before proceeding ensure that you fully understand and comprehend the full contents of
this manual. Failure to operate this equipment as directed may cause injury or death. The distributor is not
responsible for any damages or injury caused by improper use or neglect.
1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Before moving, lower the load to the lowest possible point.
5. Use only slings or chains with a rated capacity greater than the weight of the load being lifted.
6. Do not allow load to swing or drop violently while lowering or moving.
7. Center load prior to lifting.
8. No alterations shall be made to this product.
9. Make sure that boom is fully lowered before adding oil to unit reservoir.
10. Never use on a lawn mower or lawn tractor.
11. Do not rock the vehicle while working on or around equipment.
12. Equipment is design for lifting only, do not move or dolly crane when in use.
13. The following are not recommended for supporting on this equipment: Foundations, Homes, Mobile
Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc...
14. Do not use this crane for any use other than the manufacturer specied usage.
15. Failure to heed these markings may result in personal injury and/or property damage.
WARNING!
DO NOT CLIMB, HANG OR SWING.
MISUSE OF ENGINE CRANE COULD RESULT
IN A FALL THAT MAY RESULTIN SEVERE INJURY!
WARNING!
5
GENERAL SAFETY RULES
USE AND CARE
INSPECTION
GENERAL SAFETY RULES
IMPORTANT SAFETY CONSIDERATIONS
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result
in serious injury.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into this product, but must be supplied by
the operator.
CAUTION: Do not allow persons to operate or assemble this equipment until they have read this manual
and have developed a thorough understanding of how the equipment works.
• Do not modify the equipment in any way. Unauthorized modication may impair the function and/or safety
and could affect the life of the equipment. There are specic applications for which the equipment was
designed.
• Always check of damaged or worn out parts before using the equipment. Broken parts will affect the
equipment operation. Replace or repair damaged or worn parts, or missing parts immediately.
• Store idle. When equipment is not in use, store it in a secure place out of the reach of children. Inspect it for
good working condition prior to storage and before re-use.
• Not for use by children or people with reduced mental capacity.
• Do not use under the inuence of drugs or alcohol.
• Ensure children and other bystanders are kept at a safe distance when using equipment.
• Inspect the equipment carefully before each use. Ensure the equipment is not damaged, excessively worn,
or missing parts.
• Do not use the equipment unless it is properly lubricated.
• Using equipment that is not in good clean working condition or properly lubricated may cause serious injury.
• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.
DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL.
To maintain the equipment and user safety, the responsibility of the owner is to read and follow these
instructions.
• Inspect the equipment for proper operation and function.
• Keep instructions readily available for equipment operators.
• Make certain all equipment operators are properly trained; understand how to safely and correctly operate
the unit.
• Allow unit operation only with all parts in place and operating properly.
• Use only genuine replacement parts.
• Service and maintain the unit only with authorized or approved replacement parts; negligence will make the
equipment unsafe for use and void the warranty.
• Carefully inspect the unit on a regular basis and perform all maintenance as required.
• Store these instructions in the handle of your equipment.
• Keep all decals on the unit clean and visible.
6
GENERAL SAFETY INSTRUCTIONS
Position the Crane
Position the crane to only lift on the areas of the vehicle as specied by the vehicle manufacturer.
Do Not Overload Crane
Do not overload this crane beyond its rated capacity. Overloading this crane beyond its rated capacity can
cause damage to or failure of the crane.
Always Use on Hard Level Surfaces
This crane is designed only for use on hard level surfaces capable of sustaining the load. Use on unstable or
other possible loss of load.
Chock and Block (Stabilize)
Apply parking brake in vehicle before operating crane.
A chock is a wedge for steadying an object and holding it motionless, or for preventing the movement of a
wheel. Chock the wheel opposite the end being lifted.
Center Load before lifting.
Off-center loads and loads lifted when the crane is not level can cause loss of load or damage to the crane.
Do not raise or lower the vehicle unless tools, materials and people are clear.
When the lift is being lowered, make sure everyone is standing at least six feet away. Be sure there are no
tools or equipment left under or around the crane before lowering.
Always lower the Crane slowly.
DO NOT USE THE CRANE TO SUPPORT OR STABILIZE A LOAD.
Using the crane to support or stabilize a load may result in unexpected movement and result in serious injury,
being crushed and death. Always securely chock and block (stabilize) the load to be lifted. Never place any
part of the body under a raised load without properly chocking and supporting the load.
Wear ANSI-approved safety glasses and heavy duty work gloves during use.
Do not adjust the safety valve.
Stay alert. Use caution and common sense when operating crane. Do not use a crane when tired,
incoherent, dizzy, under the use or drugs or alcohol.
Training
Read this manual before use. Do not allow anyone who has not read this manual, and/or does not
understand the requirements, use the crane.
Spectators
Do not allow bystanders around the crane or under the load supported only by the crane. -Do not allow
anyone in the vehicle while the crane is in use. Keep all bystanders away from vehicle when in use.
Inspection
Inspect the crane carefully before each use. Ensure the crane is not damaged, excessively worn, or missing
parts. -Do not use the crane unless it is properly lubricated. -Using a crane that is not in good clean working
condition or properly lubricated may cause serious injury.
Additional Notes:
Save the receipt, warranty and these instructions.
Do not modify the crane in any way. Unauthorized modication may impair the function and/or safety and
could affect the life of the equipment. There are specic applications for which the crane was designed.
Always check for damaged or worn out parts before using the crane. Broken parts will affect the equipment
operation. Replace or repair damaged or worn parts immediately.
When crane is not in use, store it in a secure place out of the reach of children. Inspect it for good working
condition prior to storage and before re-use.
7
ASSEMBLY
1. Attach the casters(No.14) to the Base(No.15) with
bolts, washers, spring washers and nuts;without
tightening the nuts.
4. Connect corresponding (No.14) to the
base(No.15) with bolts, washers, spring washers
and nuts.Tighten all hardware.
5. Slide legs(No.7&8) into front of the base(No.15).
6. Lock legs(No.7&8) in place using the Ring
Pins(No.12),To insert the Ring Pins, lift up front
of Base (No.15) until holes line up. After all four
Ring Pins are inserted, insert one R-Pin (No.11)
through small hole at end of each Ring Pin until
R-Pin snaps into place.
2. Slide the caster(No.14) which is connected to the
base(No.15) along with the long holes.
3. Align the caster with the holes on the base, then
attach the casters(No.14) to the base with bolts,
washers, spring washers and nuts. Tighten all
hardware.
8
7. Use four M8x12mm Bolts (No.27) and
Washers(No.28) to fasten the Handle(No.26) to
the Post(No.18).
9. Use the M16x110mm (No.29), Washer(No.19)
and Nut(No.20) to attach the Boom(No.30) to the
top of the post(No.18).
10. Use a M16x90mm Bolt(No.17),Washer(No.19)
and Nut(No.20) to attach lower end of the
Jack(No.25) to the post(No.18) and another
Bolt(No.31),Washer(No.19) and Nut(No.20) to
attach the top of the Jack to the Boom(No.30).
8. Use the M14x90mm Bolts (No.16), Washers
(No.11), and Nuts (No.6) to secure the bottom of
the post (No.18) to the Base (No.15).
9
11. Slide the Boom Extension(No.32) into the Boom(No.30) and use the Bolt(No.16), Washer(No.11) and
Nut(No.6) to secure at the desired load rating. Use the a M16x90mm Bolt(No.33), Washer(No.11) and
Nut(No.6) to attach the Hook and Chain(No.34) to the end of the Boom Extension.
(The boom has four different load ratings; select desired rating before use.)
SYSTEM AIR PURGE PROCEDURE
IMPORTANT: BEFORE FIRST USE
Before initial use and over time it is possible that air will enter the hydraulic system, causing poor lifting
performance. Perform the following Air Purge Procedure to remove any air that may have been introduced
into the hydraulic system as a result of product shipment and handling. This step is to be completed without
any weight on the crane.
1. Turn release valve counterclockwise on full turn to
the open position.
3. With a at blade screwdriver, push the oil ll
plug slightly to the side to purge trapped air from
system. (Use caution not to tear or puncture the
oil plug.)
4. Turn release valve clockwise to the closed
position.
5. Crane is now ready for use. Check for proper
pump action.
2. Rapidly pump the handle 6-8 times. Leave handle
in down position to expose oil ll plug.
Oil Plug
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Equipos de construcción de Torin BIG RED
