76
Electric Pressure Washer Electric Pressure Washer
10. Lock the trigger and put the Spray Gun(8)
into Gun Holder(4) ,power cable to Power
Cable Hook(3).
PUMP GUARD
Specially formulated to protect your pressure
washer from freezing, corrosion and premature
wear.The pump Guard also adds lubrication
to valves and seals to prevent sticking.Highly
recommended for all POWRYTE pressure
washers!
WINTERIZING AND LONG-TERM
STORAGE
1. Disconnect all water connections.
2. Turn on the machine for a few second,
until the remaining water in the pump exits.
Turn off immediately.
3. Do not allow high-pressure hose to become
kinked.
4. Store the machine and accessories in a
room that does not reach freezing tempera-
tures. Do not store near furnace or other
sources of heat as it may dry out the pump
seals.
TIPS FOR EXTENDING THE LIFE OF
YOUR PRESSURE WASHER
1.Never operating the machine is more than
30s without water supply.
2.Pressure washer is not meant to pump hot
water. Never connect to hot water supply –
this will significantly reduce life of the pump.
3.Using detergent other than those formulated
for pressure washers may cause damage to
pump components (o-rings, etc.). This also
applies to chemicals such as bleach, dish
soap, etc.
WATER FILTER AND NOZZLE CLEAN-
ING INSTRUCTIONS
A clogged or partially clogged water filter(in
the Garden Hose Connector) or nozzle can
cause significant reduction of water pressure
coming out of the nozzle and/ or cause the
unit to pulsate while spraying.
1.The water filter was inside the Garden hose
connector(8),should be cleaned periodically.
2.Using the Nozzle Cleaning Wire(13) (taped
to the manual) provided, insert the wire into
the nozzle hole and move back and forth until
debris is dislodged. Back flush water through
the nozzles using garden hose and highest
pressure available (either standard water
nozzle or use your thumb over the nozzle to
create water pressure for back flush).
MAINTENANCE
Choose the best nozzle for the job.
Warning: Please confirm the nozzle is
pluged in position and the nozzle holder is
returned to position before squeezing the
trigger.
The angle of spray is smaller the water outlet
pressure is higher, and the material of surface
need be cleaned should be tough enough to
support higher pressure water. Detail of
intended use see items (1)-(4) below:
(1)0° nozzle,Red, Fine spot spray means
delivering a high-pressure pencil-point jet
stream. It is used to cut heavy dirt deposits in a
small concentrated area. It is ideal for dissolv-
ing stubborn substances, like tar and grease
spots on concrete, or for removing caked mud
from equipment. It is also used to clean
hard-to-reach areas including the facades of
2-story buildings or undersides of lawn mowers
and tractors.
Note: Care should be taken when setting
nozzle spray to avoid permanently gouging
wood or damaging fragile surfaces.
(2)15° nozzle,Yellow, for intense cleaning jobs
on hard surfaces that can withstand the
high-pressure. Applications include stripping
paint, removing oil stains, grease, heavy
mildew stains, and rust from steel.
(3) 25° nozzle, Green, for cleaning home
siding, brick patios, wood decks, driveways,
sidewalks, cars or furniture.
(4) 40° nozzle, White, for cleaning items
such as cars, trucks, boats, patio furniture, or
lawn equipment.
5.Squeeze the trigger of gun,the high
pressure water will flow out.(see below
picture)
6.When you finish your clean job turn the
switch to OFF(O) position.
7.Unplug the power cord from the power
outlet
8.Turn off water supply.
9.After motor and water supply are turned off,
trigger Spray Gun(8) to depressurize system.
2. Squeeze the trigger, detergent will come out
through the nozzle .
3.Apply detergent so it thoroughly covers
cleaning surface.
4. Allow detergent to remain on the surface for
a few minutes. This is a good time to use a
brush to lightly scrub heavily soiled areas.
5. Change to Spray nozzle, Rinse detergent
from surface.
6. Cleaning up: Always draw fresh water
through the detergent bottle when done to
flush any remaining detergents from the
injection system. The bottle could be
detached if necessary in this process.
11.After each use, wipe all surfaces of the
pressure washer with a clean, damp cloth.
TO WASH WITH DETERGENT
1.Screw out the bottle and fill bottle with
detergent.Connect Detergent Bottle(6) to
Spray Gun (11).
CAUTION: NEVER using pressure washer
is more than 30S after water supply off.
Serious damage could occur to the pump
and / or motor.
WARNING: NEVER disconnect high pre-
ssure discharge hose from machine while
system is pressurized. To depressurize,
turn motor off, turn water supply off and
squeeze gun trigger 2-3 times.
WARNING:Acids, alkalines, bleaches,
solvents, can corrode the soap nozzle.
