Tonze aw 6660 Manual de usuario
User’s Guide
0
Wireless 802.11ag AP
User’s Manual
Version 1.0
User’s Guide
1
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
whether electronic, mechanical, photocopyin , recordin , or otherwise without the prior writin of the publisher.
MAY. 2005
User’s Guide
2
Contents
1. Introduction................................................................................................................ 3
2. Safety Notification...................................................................................................... 4
3. Hardware Installation................................................................................................. 5
4. How to Confi urin the Dual Band AP ....................................................................... 8
4.1 Setup – Network Setup............................................................................................ 9
4.2 Wireless – Wireless Settin s ................................................................................. 10
4.3 Wireless – Wireless Mo e ................................................................................... 12
4.4 Wireless MAC Filter............................................................................................... 13
4.5 Wireless – Wireless Security ................................................................................. 14
4.6 Wireless – Advanced Wireless Settin s................................................................. 15
4.7 Administration – Mana ement ............................................................................... 18
4.8 Administration – Reboot AP ................................................................................... 19
4.9 Administration – Firmware Up rade....................................................................... 20
4.10 Administration – Factory Defaults ........................................................................ 21
4.11 Status – Local Network ........................................................................................ 22
4.12 Status – Wireless Network................................................................................... 23
4.13 Status – Wireless Statistics .................................................................................. 24
5. Troubleshootin – Q & A.......................................................................................... 25
User’s Guide
3
1. Intro uction
Thank you for purchasin your Wireless 802.11a AP.
This user uide will assist you with the installation procedure.
User’s Guide
4
2. Safety Notification
Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please keep the unit away
from water and other dama in elements. Please read the user manual thorou hly before you install the device.
The device should only be repaired by authorized and qualified personnel.
Please do not try to open or repair the device yourself.
Do not place the device in a damp or humid location, i.e. a bathroom.
The device should be placed in a sheltered and non-slip location within a temperature ran e of +5 to +40 Celsius
de ree.
Please do not expose the device to direct sunli ht or other heat sources. The housin and electronic components may
be dama ed by direct sunli ht or heat sources.
User’s Guide
5
3. Har ware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the followin table for the meanin of each feature.
Power
The Power LED li hts up and will keep while the AP is powered on. When the AP oes throu h its self-
dia nostic mode durin every boot-up, this LED will flash. When
the dia nostic is complete, the LED
will be lit continuously.
11a
The 11a LED flashes when there is a successful Wireless-A connection.
11b/g
The 11b/g LED flashes when there is a successful Wireless-B/G connection.
LAN
The LAN
LED li hts up when Ethernet port of AP was connected to LAN. When the LED is flashin that
indicates the network activity over that port.
User’s Guide
6
Rear Panel
The rear panel features 1 Ethernet port, Reset button and Power port. Refer to the followin table for the meanin of
each feature.
RESET Button
The RESET button can restore device to factory default settin s by press this button for approx
. 10
seconds durin device power on status.
LAN
The port connects the AP to your networked PCs and other Ethernet network devices.
Connectors There are two RPSMA Female connectors, Ant 1 is for 802.11a and Ant 2 is for 802.11b/ .
Power
The POWER port is where you will connect the power adapter.
AP Default Settings
User
Password admin
IP Address 192.168.1.250
Subnet Mask 255.255.255.0
RF ESSID A band: wlan-a G band: wlan-
Channel A band: Auto G band: 6
Mode G band: Mixed
Encryption Disabled
RESET
Ethernet Power
User’s Guide
7
Har ware Installation for Connection to Your local network
1. Power off your network devices.
2. Locate an optimum location for the AP. The best place for the AP is usually at the center of your wireless network,
with line of si ht to all of your wireless devices.
3. Adjust the antennas. Normally, the hi her location of your AP will et better the performance.
4. Usin a standard Ethernet network cable, connect the AP’s Internet port to your broadband modem.
5. Connect your network PCs or Ethernet devices to the AP’s LAN ports usin standard Ethernet network cablin .
6. Connect the AC power adapter to the AP's Power port. Then connect the other end to an electrical outlet. Only use
the power adapter supplied with the AP. Use of a different adapter may cause product dama e.
7. The Hardware installation is completed, please refer to the followin content for AP confi uration.
User’s Guide
8
4. How to Configuring the Dual Ban AP
START UP & LOGIN
In order to confi ure the Wireless 11a AP, you must use web browser and manually input http://192.168.1.250 into the
Address box and press Enter. The Main Pa e will appear.
In order to confi ure the Wireless 11a AP, you must input the password into the Passwor box and leave blank on the
User Name box. The default password is “a min”.
Once you have lo ed-in as administrator, it is a ood idea to chan e the administrator password to ensure a secure
protection to the Wireless 11a AP. The Security Settin s section described later in this manual describes how to chan e
the password.
Once you have input the correct password and lo ed-in, the screen will chan e to the Setup pa e screen.
TURN ON POWER SUPPLY
Quick power cycle would caused system corruption. When power on, be careful not to shut down in about 5 seconds,
because data is writin to the flash.
User’s Guide
9
4.1 Setup – Network Setup
This followin screen contains all of the AP's basic setup functions.
Most users will be able to confi ure the AP and et it workin properly usin the default settin s.
Network Setup
Identity
Device Name: These fields allow you to input a host name for the AP.
Local Area Network
♦ Dynamic: If your LAN supports DHCP assi nin dynamic IP address then please select this type.
♦ Static IP:
This’ s default connection type. If you are required to use a fixed IP address to connect to the LAN, then select
Static IP.
IP A ress: This’ s the AP’s IP address.
Subnet Mask: This’ s the AP’s Subnet Mask.
Default Gateway: This’ s the AP’s Gateway Address.
Those above items can be adjusted that depends on real network architecture if it is necessary.
Chan e these settin s as described here and click the Apply button to apply your chan es or click Cancel to cancel your
chan es. For additional information, click Help.
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To chan e the confi uration, use Internet Explorer (IE) or Netscape Communicator to connect the WEB mana ement
192.168.1.250.
Otros manuales para aw 6660
1
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Tonze
