TMT TA Series Manual de usuario

- 20 -

MEMO

- 1-

TAseries

V106

CRANE SCALE

Operating Manual

www.tmteng.com

- 18 -

◆ Wireless specification

RF frequency range 2400 ~ 2483.5 MHz

Output power Max. 4dBm

Channel width 2 MHz

Frequency offset < ±30ppm

Transmit data rate 250Kbps,500Kbps

Receiver sensitivity -99dBm (PER <1%)

Maximum input level 0dBm

RF In/out impedance 50 ohm (TXRF, RXRF)

Spurious(2nd harmonics) < -30dBm

Radio link effective range Approx. 100M (Open space)

- 3-

1. Instruction

This operating manual is the specifications for our TA series.

The TA series is the product of years of design, development, and complete testing.

This TA series has been designed with reliability, under rigid quality control and with

outstanding performance.

This MANUAL included with basic technical information about composition of hardware

and programmatic functions.

■ Precaution

Please check if the safety hook is connected well before you install our TA series, so

that the SHACKLE is not separated.

◆ Don’t install the TA series in direct sunlight.

◆ Avoid sudden temperature changes, vibration, wind, water, or excessive dirt.

◆ Avoid from the shock of excessive weight.

◆ Place the scale away from water.

◆ Weigh a thing on the scale in vertical direction as follows.

(Refer to following picture.)

- 16 -

9. Remote Control

(1) How to use

■ : Used to power off the scale

(Power-ON is available only on scale.)

■ : Same as Keyboard

■ (CLEAR) : Used to clear previously added weights.

■ : SUM KEY : Used to add weights.

If press a SUM KEY, the sum of weights is displayed.

After that, about 2 sec later, a weighing mode is reverted.

Battery for a Remote Control : AA size, 1.5V, 2 pcs

(2) Specification

List Description

Available Distance 6 m ∼ 10 m

Available Angle 60 °

Power 3V (1.5V AA 2pcs)

- 5-

◆ Overall View

TA100/500 TA200

◆ Size

TA100/500 TA200

3. Technical Specifications

- 14 -

■ F16 : Initialization of number measured daily (weigh No.) - Wireless option

Setting Menu Description

F16-0 Maintain current number

F16-1 Initialization (starting from No.1)

■ F17 : Auto print - Wireless option

Setting Menu Description

F17-0 Not used

F17-1 Auto print (include print format)

F17-2 Auto print (only weight data)

F17-3 Wireless Auto print (include print format)

F17-4 Wireless Auto print (only weight data)

■ F18 : Hold data auto print - Wireless option

Setting Menu Description

F18-0 Not used

F18-1 used

8. Testing Mode

(1) How to use

■ Press the (TARE Key) with the (ON/OFF Key).

Then, the scale switches into a Testing Mode.

(2) Keyboards

■ SET : Used to move into next menu.

■ ZERO , TARE , HOLD : Used when the scale is been testing.

(3) Testing Menu (TEST 1 – TEST 6)

■ TEST 1 : Keyboard Test

KEY

Display Description

ZERO

If you push the button that you want to test,

the key number is appeared on the display.

If press the (SET Key), it moves into TEST 2.

TARE

HOLD

SET

- 7-

4. Display and Keys

◆Display Description

Weight Displays the accurate weight

STABLE Displays that weight is Stable

ZERO ZERO Displays that current weight is Zero

TARE TARE Displays the net weight, when the tare is included

HOLD HOLD Used to weigh an unstable or moving thing

BATTERY Displays when a battery has to be recharged

◆Key Function

Key Description

ON/OFF Turn on and off the scale

ZERO Reset scale to zero

TARE Input a tare weight

HOLD Weigh an unstable and moving thing (Manual / Auto)

SET Testing Mode or Returning a new Mode

- 12 -

■ F05 : Backlight Mode (0~2)

Setting Menu Description

F05-0 Manual ON/OFF

F05-1 Automatic ON/OFF (weighing : ON / zero : OFF)

F05-2 Backlight ON.

■ F06 : Automatic Zero Condition (00~99)

Setting Menu Description

F06-00 No compensation

…

F06-23 Compensation for gradual change below 1 division for 3

…

F06-99 Compensation for gradual change below 4.5 division for 9

■ F07 : Auto Hold Start

Setting Menu Description

F07-0 Manual

F07-1 Automatic

■ F08 : Initialization Hold Weight (1~9)

Setting Menu Description

F08-0 Zero (0)

…

F08-3 Below 3 division

…

F08-9 Below 9 division

■ F09 : Function * key - Wireless option

Setting Menu Description

F09-0 Use to clear previously added weights.

F09-1 Print command key

F09-2 Weighing data send to computer

F09-3 Wireless print command key (include print format)

F09-4 Wireless print command key (only weight data)

F09-5 Used to clear previously added weights.

■ F10 : Device number (Identification number of each scale) - Wireless option

Setting Menu Description

F10-0 Device No.0

…

F10-5 Device No.5

…

F10-9 Device No.9

- 9-

6. General Functions and Description

(1) Operating Method

■ Press the (ON/OFF Key) on the front panel of the scale. The scale will be

ready for weighing when ZERO lamp is on.

(2) ZERO Function

■ If press the (ZERO Key), the ZERO is displayed after correcting zero range

by itself. The Zero range is corrected within 2% of maximum weight.

If weigh is unstable, the ZERO Key doesn’t work.

(3) Setting Function of Tare Weight

■ Place the tare on hook and push the (TARE Key). Then, the TARE is displayed

and the display turns ZERO state.

■ In order to delete the tare weight, remove the tare or a thing to be weighted on the

hook and press the (TARE Key).

The TARE is off and the scale returns in normal mode.

If weight is unstable, (TARE Key) doesn’t work.

The sum of both a tare weight and a weighing weight cannot be exceeded over the

maximum capacity of the scale.

(4) Zero Calibration Function

■ Under the ZERO state (ZERO lamp is on.), if the weight change is below the half of

the scale graduations, the scale turns automatically Zero.

- 10 -

(5) HOLD Function

① Auto-Hold Function

(This function works every time the scale weighs all the things.)

■ Under the Zero state, press the (HOLD Key).

■ The weight display will indicate the message.

■ is displayed.

■ After placing a thing on hook, if the weight change is stable, then a display shows

the message and average weight will appear.

■ The weight of a held thing is displayed.

■ In order to escape from the Auto-Hold function, push the HOLD key under the

ZERO state. Then, after the message will be displayed, the is

off and the scale turns into normal mode.

② Manual-Hold Function

(Only when you press a HOLD key, the HOLD function works.)

■ Place a thing on hook and press the (HOLD Key).

The message appears and the is displayed. The Average

weight appears.

■ The held weight is displayed.

■ In order to escape from the Manual-Hold function, remove a thing or press the

( HOLD Key). Then, the is off and the scale returns into the normal

mode.

- 11 -

7. Setting Mode

(1) How to use

■ Press the (HOLD Key) with the (ON/OFF Key).

Then, the scale switches into Setting Mode.

(2) Keyboard

■ ZERO : Used to initialize the scale to ZERO.

■ SET : Used to save the setting constant changed and to move

into next setting menu.

■ HOLD : Used to increase the setting constant one by one.

(3) Setting Menu (F1 – F18)

■ F01 : Adjustment the speed of weight change (1∼9)

Setting Menu Description

F01-1 Very fast

…

F01-5 Normal

…

F01-9 Very slow

■ F02 : Weight Storage Function

Setting Menu Description

F02-0 Not used

F02-1 Use

■ F03 : Adjustment the hold speed (1∼9)

Setting Menu Description

F03-1 Very fast

…

F03-5 Normal

…

F03-9 Very slow

■ F04 : Stable condition set of weight (1~9)

Setting Menu Description

F04-1 Sensitive

…

F04-5 Normal

…

F04-9 Insensitive

- 8-

5. Use of Battery Charging

(1) How to charge a battery

■ Check the power supply (AC : 100V~240V)

■ If adaptor is still being charged, the RED lamp is on as a below picture.

■ If a charging is completed, the GREEN lamp is on.

The battery charging time takes about 5hr.

(The battery charging time is subject to be changed according to battery condition.)

Charging Completed

(2) Charger (Lithium polymer battery)

Capacity 4000mAH

Power 3.7V

(3) “LOW BATTERY” Sign

■ In order to prevent a battery being overcharged, the sign is displayed.

After 6 hours later, power is automatically off. (It’s subject to be changed

according to the using condition.)

- 13 -

■ F11 : Item number (Identification number of each Item) - Wireless option

Setting Menu Description

F11-0 Item No.0

…

F11-5 Item No.5

…

F11-9 Item No.9

■ F12 : Data set sent to computer - Wireless option

Setting Menu Description

F12-0 No data output

F12-1 Command mode

F12-2 Transmission in an state of stable & unstable.

F12-3 Transmission only in stable state

■ F13 : Wireless real time communication - Wireless option

Setting Menu Description

F13-0 Not used

F13-1 Auxiliary display

F13-2 TF200 (Wireless dongle)

■ F14 : Print line feed - Wireless option

Setting Menu Description

F14-0 1 line feed

…

F14-5 6 line feed

…

F14-9 10 line feed

■ F15 : Print form - Wireless option

Setting Menu Description

F15-0 Form 0 (serial No., Item No., weight)

F15-1 Form 1 (weigh No., Item No., weight)

F15-2 Form 2 (weight)

[FORM 0]

001, ID_9, 25 kg

[FORM 1]

SN_012, ID_9, 25 kg

[FORM 2]

25 kg

62 kg

- 6-

◆ Specification

Model #. TA-100

(General Type)

TA-200

(Meat Shop Type)

TA-500

(General Type)

Capacity

(Graduations) 0 ~ 100kg (0.05kg) 0 ~ 200kg (0.1kg) 0 ~ 250kg (0.1kg)

250 ~ 500kg (0.2kg)

Weight 2.6kg

Maximum Tare

Weight Full Tare

Operating Time 350 hr

Display 5 Characters, LCD, (Character Size : 20mm)

Temperature -10℃ ~ 40℃

Keys ON/OFF, ZERO, TARE, HOLD, * (Back-light)

Display LOW BATT, BATTERY State, ZERO, NET, HOLD, STABLE,

“-“ (Minus)

Accessories Rechargeable Battery

Zero Point Within +/- 2% of Maximum Weight

Initial Zero Point Within +/- 10% of Maximum Weight

Adaptor Power

Supply

Input : AC 100V~240V, 50/60Hz

Output : 5V 1000mA

◆Part List

1) Crane Scale : 1 EA

2) Adaptor : 1 EA

3) Infra Red Remote Controller : 1EA

- 15 -

■ TEST 2 : Display Test

Display Description

TEST 2 operat es automatically an d the whole dis play is ON.

If press the (SET Key), it moves into TEST 3.

■ TEST 3 : A/D Conversion Test (Load Cell Test)

Display Description

The value is the conversion constant for A/D.

The value may be different according to scale models.

If press the (SET Key), it moves into TEST 4.

Please check if the displayed number is changed well with giving some force to the

hook. If the displayed number is not changed and remains “0”, then it needs the

service after sales. Therefore, contact us.

■ TEST 4 : Backlight Test

화면 설명

: Backlight ON/OFF

If press the (SET Ke

), it moves into the weighing

mode.

■ TEST 5 : RS232C TEST

Display Description

Ex) 49-13 : Transmit 49 (ZERO KEY)

Receiver 13 (PC ENTER KEY)

(ZERO KEY 49, TARE KEY 50, HOLD KEY 51)

■ TEST 6 : Wireless communication test - Wireless option

Press (ZERO KEY) at the scale. The numeric character increases on the auxiliary

display.

- 4-

2. Main Features

◆ Super mini small size and portable

◆ Lithium polymer battery built-in => Long battery lifetime by one-time charging.

◆ Convenient Charging Method

-Auto Charging after connecting a rechargeable adaptor

(Charging Time : approx. 5 hr)

-Auto Power Cut-Off after the charging is completed.

(Full Charging lamp displays.)

◆ Very easy to exchange the used Shackle in a new one.

◆ As per the using purpose, General Type (TA-100,500), Meat Shop (TA-200)

- 17 -

10. RS232C & Wireless option

■ RS-232C port connection

Connect serial port of the scale to serial port of PC as follows.

(RED) TXD ------------------------------ RXD (2)

(WHITE) RXD ------------------------------ TXD (3)

(GREEN) GND ------------------------------ GND (5)

[RS232C wire of TA] [Serial port of computer]

■ Data format

Type : EIA-RS-232C

Method : Full-duplex, asynchronous transmission Format

① Baud rate : 9600 bps

② Data bit: 8, Stop bit: 1, Parity bit: None

③ Code : ASCII

④ When data is sent to computer? Set in SET mode(F12).

⑤ Format (18byte)

Start code Blank Lamp status Weighing data Unit Stop code

S(U) T(S) , , +/- 7byte k g CR LF

- Start code : ST (Stable) / US (Unstable)

- Lamp status byte

Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

One

decimal

point

Two

decimal

point

Three

decimal

point

Stable Zero Tare Hold

- Weighing data (8byte)

a. 13.5 ㎏ : '+', ' ', ' ', ' ', '1', '3', '.', '5'

b. 135㎏ : '+', ' ', ' ', ' ', ' ', '1', '3', '5'

c. -135 ㎏ : '-', ' ', ' ', ' ', ' ', '1', '3', '5'

- 2-

INDEX

1. Instruction ················································································ 3

2. Main Features ·············································································· 4

3. Technical Specifications ······························································· 5

4. Display and Keys ···········································································7

5. Use of Battery Charging ···································································8

6. General Function and Descriptions ·····················································9

7. Setting Mode ··············································································11

8. Testing Mode ············································································· 12

9. Remote control············································································ 13

10. RS232C & Wireless option ·····························································14

11.Error Message and Self-Testing methods ···········································14

- 19 -

11. Error Message and Self Testing methods

▣ Error 1

zMessage : Data in an internal storage allocation are erased owing to any

electrical impact.

zSelf-Testing Method : Please contact us to resolve this technical problem.

▣ Error 2

zMessage : something wrong in a Load Cell connection or in an A/D conversion.

zSelf-Testing Method : Please contact us to resolve this technical problem.

▣ Error 3

zMessage : The initial zero range is exceeded within +/- 10% of maximum weight

value.

zSelf-Testing Method : Please check if a book is empty.

▣ Error

zMessage : When a thing is over-weighed within the maximum weight value, the

error message is displayed.

zSelf-Testing Method : Do not weigh the thing whose the limit of a maximum

weight value is exceeded.

If a load cell is broken, then the load cell has to be replaced.

Tabla de contenidos

Otros manuales de Escala de TMT

TMT

TMT TCB Series Guía de inicio rápido

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario