TMS Lite High Current Series Manual de usuario

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

________________________________________________________

LC-18-1CH-X10

LC-18-2CH-X5

High Current Series Lighting Controller Unit

USER MANUAL

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Table of Contents

Hardware ................................................................................................................................................2

Packing List..........................................................................................................................................2

General Description ................................................................................................................................3

Specification........................................................................................................................................3

Connectors Description...........................................................................................................................4

Operation Mode .....................................................................................................................................7

Constant Mode ...................................................................................................................................7

Strobe Mode .......................................................................................................................................7

Trigger Mode.......................................................................................................................................8

Current Multiplier ...................................................................................................................................8

LC-18 Software........................................................................................................................................9

Change IP Address.................................................................................................................................12

Slave Board Address Setting .................................................................................................................13

Communication Connection .............................................................................................................14

Input Signal ...........................................................................................................................................15

Output Signal ........................................................................................................................................15

Accessories............................................................................................................................................16

24V Power Supply.............................................................................................................................16

Cable Selection..................................................................................................................................17

Cable Information .................................................................................................................................18

Power Cord Information .......................................................................................................................19

Drawing Dimension...............................................................................................................................20

Revision Notes

Rev

Date/Author

Comment

1.0

Sept2020/KW

First Revision

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Hardware

Packing List

Please ensure the following items are in the package:

LC-18 High Current Series Controller Package

LC-18-M

LC-18-2CH-X5 / LC-18-1CH-X10

Ethernet Cable x1

RS232 Cable x1

Communication Cable x1set

24V Power Supply (Optional)

Lighting Cable x 1pcs/2pcs (Optional)

User Manual x1

User Interface (download from the link below)

Link for user interface and user manual from TMS LITE website:

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

General Description

The LC-18 high current controller provides intensity control of high current LED lightings for

machine vision applications. The controller consists of 16 channels with individual settings for

each channel. Thereare 3 modes of operation provided to support different types of application.

Specification

Parameter

Value

Controller Supply Voltage

24 VDC

Lighting Supply Voltage

5/12/24/48 VDC

(According to Lighting Voltage Rating)

No. of Channel

LC-18-1CH-X10

1 Channel

LC-18-2CH-X5

2 Channels

Channel Mode

Constant, Strobe, Trigger

Output Current

Maximum current per channel

LC-18-1CH-X10

10A

LC-18-2CH-X5

Strobe Delay, Strobe Width,

Output Delay, Output Width

Adjustable 0 –99.99ms (10us/step)

Input Trigger Signal

3.3-24V, >5mA

rising/falling edge trigger

Output Trigger Signal

Support rising/falling edge output trigger

Trigger Delay

≤ 20us

Software Control

RS232 / TCPIP

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Connectors Description

Terminal

Function

VS (24V)

Controller Power Supply +

GND

Controller Power Supply –

COMM

Communication Port (between master and slave boards)

RS232

RS232 Communication

TCPIP

TCPIP Communication

ADDR

4 Way DIP Switch (for slave address selection)

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Terminal

Function

LIGHT INPUT +

Power Supply for Lighting +

LIGHT INPUT –

Power Supply for Lighting –

CH +

Lighting Channel Output +

CH –

Lighting Channel Output –

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Terminal

Function

IN +

External Input +

IN –

External Input –

OUT +

External Output +

OUT –

External Output –

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Operation Mode

Constant Mode

Constant mode offers continuous lighting intensity control. Lighting intensity is controlled

using constant current technique. Brightness can be adjusted from fully off to fully on in the

range of 0 –255.

Strobe Mode

Strobe mode provides short interval triggering for applications that require high intensity and

high precision. An input trigger signal will turn on the lighting output based on pre-set delay

and duration parameters.

There are 4 adjustable strobe parameters available:

Strobe Delay = Delay time between the external input signal and the lighting output

Strobe Width = Duration of the lighting’s turn on time

Output Delay = Delay time between the external input signal and the external output signal

Output Width = Duration of the external output signal’s turn on time

Parameter timings are in the range of 0-9999 which is equivalent to 0-99.99ms (in step of 10us)

External Trigger

Lighting Strobe

Camera Output

Strobe Delay

Strobe Width

Output Delay

Output Width

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

Trigger Mode

Trigger mode provides most flexibility for variable timing light output. The light output ON

when input trigger signal received and OFF when no input signal.

Current Multiplier

Current Multiplier setting provides more precise control of lighting intensity for lightings with

different current ratings.

Ex:

Maximum Current = 5A

Current Multiplier setting range = 1-10

1 = 10% of max output current (500mA)

2 = 20% of max output current (1000mA)

3 = 30% of max output current (1500mA)

4 = 40% of max output current (2000mA)

5 = 50% of max output current (2500mA)

6 = 60% of max output current (3000mA)

7 = 70% of max output current (3500mA)

8 = 80% of max output current (4000mA)

9 = 90% of max output current (4500mA)

10 = 100% of max output current (5000mA/5A)

For example: if the lighting’s current rating is 1450mA, current multiplier can be set to 3,

setting the maximum output current to 1500mA. So the lighting’s intensity can be adjusted

from low to high within the range of 0-255.

If multiplier is set too high, for example 10 (100% of max output = 5A), the adjustable intensity

range for the lighting is only about 0-74. Setting the intensity value to 75 or higher will not

have any effect towards the lighting output brightness.

External Trigger

Lighting Strobe

TMS Lite LC-18-1CH-X10 & 2CH-X5 CONTROLLER UNIT

LC-18 Software

The controller can be controlled using LC-18 software. Connect the controller to computer

with RS232 cable and TCPIP cable.

LC-18-2CH-X5 (2 Channels only)

1. Software Connection :

a. Select COMPORT or TCPIP to connect.

b. Disconnect the software

2. Read and Save function for all slave board :

a. Read all slave board’s parameter from controller.

b. Save all slave board’s parameter into EEPROM.

3. Strobe function for all channel :

a. Strobe all channel once.

b. Repeat strobe all channel (together).

c. Repeat strobe channel by channel.

4. Reset all channel’s parameter to default value.

5. Master board firmware version.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de TMS Lite

TMS Lite

TMS Lite SDH-1000-D1 Manual de usuario

TMS Lite

TMS Lite LC-18-SQ-4CH Manual de usuario

TMS Lite

TMS Lite ANGX-1000-CH1-24V Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario