TLS Electronics 875760 Manual de usuario
875760 HDbaseT/HDMI/Audio Matrix 4x4
Manual
875760 HDBaseT/HDMI/Audio Matrix 4x4
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjust-
ing this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the life
of your equipment.
SAFETY AND NOTICE
1. The transmission distances of HDMI over UTP cables are measured using
TE CONNECTIVITY 1427071-6
2. EIA/TIA-568-B termination (T568B) and “AWG24/1 solid wire” for CAT
cables is recommended for best performance.
3. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POE OVER-CURRENT
and damage POE components. Please use straight-through CAT cable (both
RJ45 headers are 568A or 568B standard).
4. It is recommended that power up the device after connections of source, sink
and CAT cable.
5. To reduce the interference among the unshielded twisted pairs of wires in
CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables. Shielded CAT cables can be used
to improve EMI problems, which is worsen in long transmission.
6. Because the quality of the CAT cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality,
the actual transmission range is subject to one’s choice of CAT cables.
7. Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS electronics GmbH approved Replacement Part.
Doing so will void the warranty and potentially expose the user to
dangerous voltages resulting in an electrical shock.
8. Do not disassemble the device for any reason. Doing so will void the manu-
facturer’s warranty. Also, our unique case is an integral part of the design of
this unit and is responsible for cooling and circuitry shielding. Any modifica-
tions to this case will potentially cause malfunction and product failure.
9. Do not expose the device to water, moisture, or liquids. Possible electric
shock may result as well as failure of the unit to operate.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Table of Contents
1. Introduction.............................................................................................5
2. Features.....................................................................................................5
3. Panel Descriptions.......................................................................................6
4. Remote Control Descriptions......................................................................10
5. Specifications...............................................................................11
6. Application Diagram...........................................................................12
7. Package Contents......................................................................................13
8. RS-232 Pin Assignment.......................................................................13
9. RS-232 and Telnet Commands ...............................................................14
10. GUI control..............................................................................................16
11. Maintenance..............................................................................................27
12. Warranty Policy...................................................................................27
13. Limitations of Warranty........................................................................27
14. Exclusive Remedies...........................................................................28
15. RMA Policy...........................................................................................28
875760 HDBaseT/HDMI/Audio Matrix 4x4
Introduction:
The HDBaseT/HDMI/Audio Matrix 4x4 routes four Hi-Def sources to any four
HDTV displays, supporting 1080p Full HD up to 4K@30Hz UHD plus all 3D
formats, along with multichannel digital audio formats such as Dolby® True HD
and DTS-HD® Master Audio™. Embedded audio extractors can extract the
audio and output via L/R or Coaxial. Volume can be controlled for analogue
audio out. Based on HDBaseT Lite chipset inside, the output distance can reach
up to 70m via Cat5e/Cat6. Each source can be routed to any display using the
front-panel push buttons, IR remote control, RS-232 interface, or via TCP/IP.
Features:
•HDCP 2.2 compliant
•Supports resolutions up to 1080p@60Hz, 4K@30Hz, 36-bit deep color
•HDBaseT Lite chipset inside for the output distance up to 70m.
•Matrix can power the remote receivers, with POH, no power supply needed
for the receivers.
•Allows any source to be displayed on multiple displays (HDBaseT & HDMI)
at the same time
•Allows any HDMI display to view any HDMI source at any time
•Dolby TrueHD and DTS-HD master audio pass through HDMI output
•Volume control with Telnet and RS232 on deembedded audio
•Advanced EDID management for rapid integration of sources and displays
•Front-panel LCD display for status feedback
•Multiple switching mode: push-in button, IR remote control, RS-232 control,
and TCP/IP control
•Easy installation with rack-mounting ears
•Full 3D pass- through.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Panel Descriptions
Front Panel
1. LCD display---Show the status of input-output selection, EDID info and so on.
2. IR receiver window----Receive the IR from the remote control.
3. Power LED indicator---Indicate the status of the power for the matrix.
4. Power button---Press to power on/off the matrix.
5. HDMI output selection button 1 to 4---First Press - select the output from
button 1 to button 4
12. HDMI input selection button 1 to 4---Second Press - select the input from
button 1 to button 4
6. All button for HDMI outputs---Press to select all of the outputs from 1 to 4.
7. Menu button---Press to enter EDID set mode. Three EDID segments will
display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example:
IN1 1080P 2.0CH, means to set 1080P 2.0CH EDID to INPUT1. The blinking
segment is the one can be changed currently. Segment content items as
below:
875760 HDBaseT/HDMI/Audio Matrix 4x4
INPUT
VIDEO
AUDIO
Note
IN1 1080I 2.0CH.
IN2 1080P 5.1CH
IN3 3D 7.1CH
IN4 D1024 D1024=DVI 1024 x 768
IN5 D1080 D1080=DVI 1920 x 1080
IN6 D1200 D1200=DVI 1920 x 1200
IN7 OUT1 OUT1=Copy OUTPUT1 EDID to INPUTx
ALL OUT2 ALL=Set EDID to ALL INPUTs
OUT2=Copy OUTPUT2 EDID to INPUTx
OUT3 OUT3=Copy OUTPUT3 EDID to INPUTx
OUT4 OUT4=Copy OUTPUT4 EDID to INPUTx
OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx
OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx
OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx
OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx
8. Up selection button--- Press to change segment’s value.
9. ESC---Press to quit EDID set mode.
10. Lock LED indicator---Indicate the status of Lock.
11. Lock button---Press to lock the buttons of the front panel.
12. HDMI input selection button 1 to 4---Press to select the input from 1 to 4.
13. PTP button---Press to mirror all inputs and outputs (e.g. output 1 to input1,
output 2 to input2 and so on).
14. Selection button---Press to select segment to change setting. Selected
segment will be blinking.
15. Down selection button---Press to change segment’s value.
16. Enter button--- Press to set EDID to specified INPUT or copy EDID from
specified OUTPUT to specified INPUT.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Back Panel
1. GND --- Connect to ground.
2. IR inputs 1 to 4 --- 3.5mm stereo phone-jack, work with control processor.
3. IR outputs 1 to 4 --- 3.5mm mono phone-jack, connect to IR transmitter cable.
4. RS232 port with each HDBT out--- Connect to PC, and work with the remote
receiver.
5. Coaxial digital audio output --- Extracted audio corresponding with the HDMI
video output
6. L/R analog audio output --- Extracted audio corresponding with the HDMI
video output.
7. TCP/IP port – TCP/IP control
8. RS232 port – For control the matrix from PC or control processor
875760 HDBaseT/HDMI/Audio Matrix 4x4
9. DIP switch – Used for global EDID settings
3 2 1 0 EDID type
Combination of DIP positions
0 0 0 0 1080P 2.0CH
0 0 0 1 1080P 5.1CH
0 0 1 0 1080P 7.1CH
0 0 1 1 1080i 2.0CH
0 1 0 0 1080i 5.1CH
0 1 0 1 1080i 7.1CH
0 1 1 0 3D 2.0CH
0 1 1 1 3D 5.1CH
1 0 0 0 3D 7.1CH
1 0 0 1 4K 2.0CH
1 0 1 0 4K 5.1CH
1 0 1 1 4K 7.1CH
1 1 0 0 DVI 1280x1024
1 1 0 1 DVI 1920x1080
1 1 1 0 DVI 1920x1200
1 1 1 1 Software Control EDID
10. HDMI inputs 1 to 4--- Connect HDMI sources
11. HDBT outputs 1 to 4--- Work with remote receivers for long distance trans-
mission.
12. HDMI outputs 1 to 4--- Output for displays, AVR etc.
13. IR extension receiver input --- 3.5mm stereo phone-jack, connect to IR
receiver cable to receive the IR from remote of the matrix.
14. Power port--- Use included 24V/3.5A DC adaptor to power the matrix.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Remote Control Description
Output and Input select
A. OUTPUT-X select INPUT-Y:
1. Press OUTPUT-X (X means 1 to 4 of outputs)Press INPUT-Y( Ymeans
1 to 4 of inputs )
2. Press OUTPUT-X (X means 1 to 4 of outputs)press the left and right
arrow buttons to select the input.
B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTPress
INPUT-Y button ( Y means 1 to 4 of inputs ), then INPUT-Y switched to ALL
OUTPUTS
C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc):
Press PTP button in Zone OUTPUT
EDID Set Up
A. Fixed EDID to INPUT-Y/ALL
Press 1080I/1080P/3D/4KPress 2.0CH/5.1CH/7.1CHINPUT-Y/ALL
button in Zone INPUT
875760 HDBaseT/HDMI/Audio Matrix 4x4
B. Copy EDID of OUTPUT-X to INPUT-Y/ALL
Press COPY buttonPress OUTPUT-X buttonPress INPUT-Y/ALL button
C. User defined EDID to INPUT-Y/ALL
Press USER1/USER2 buttonPress INPUT-Y/ALL
NOTE: Pressing button sequence should be finished in 5 seconds, otherwise,
operation discarded.
Manual Output and Input select
First Press: OUTPUT select, output button 1 to 4
Second Press: INPUT select, output button 1 to 4
Specifications:
Bandwidth 2.97Gbps per color
Video Input Connectors 4x HDMI Type A, 19-pin, female
Video Output Connectors 4x HDMI Type A, 19-pin, female, 4x RJ45 Connector
Audio Output Connectors 4x RCA(SPDIF), 4x L/R
RS232 Serial port DB-9, female
TCP/IP Control 1x RJ45, female
IR input ports 5x3.5mm stereo jack
IR output ports 4x3.5mm mono stereo jack
Rack-Mountable rack ears included
Dimensions(Lx Wx D) 428mm x 235mm x 43mm, w/o feet
Shipping Weight 2.7KG
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature -4°F to 140°F (-20°C to 60°C)
Power Supply 24V/3,5A DC
Tabla de contenidos
Otros manuales de Sistema de control de TLS Electronics
