TLI VOLspeed Hoja de especificaciones
1
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
VOLspeed Ebike Tuning
Bosch Active Line
Bosch Performance Line
V3
Operating Manual
Installation Guide
2
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
Attention!
Read these instructions completely before using the device, keep the
instructions and pass them on when handing over the device to other
persons.
Product Features
The device offers the following functions after installation in eBikes with Bosch drive system
(20 / 25 / 32 / 45 km/h):
Individual activation code adjustable
Speed limit adjustable via handlebar control buttons
Adjustable dynamic mode with reduced "wall effect"
Correct display of speed and distance
Correct mileage after removal of the tuning module
Optimized range calculation with active tuning
Battery indication in percent alternating with the range when tuning is active
Workshop mode
All settings are made via the handlebar control buttons on the eBike. No smartphone or
notebook is required.
The electronic is cast into the housing and thus safely protected against moisture.
Intended Use
The device is only suitable for installation in eBikes with the following Bosch drive systems:
Drive system:
Display type:
Active Line
Intuvia, Purion, Nyon, Kiox, Nyon2
Active Line plus
Intuvia, Purion, Nyon, Kiox, Nyon2
Performance Line
Intuvia, Purion, Nyon, Kiox, Nyon2
Performance Line CX
Intuvia, Purion, Nyon, Kiox, Nyon2
Cargo Line
Intuvia, Purion, Nyon, Kiox, Nyon2
Legal and Safety Notes / Product Liability
Operation of the eBike in public traffic is no longer permitted after installation of
the module. The use is only allowed on private areas or designated test and race
tracks.
Damage caused in conjunction with the operation of the eBike will no longer be
covered by private liability insurance after installation.
Liability and warranty claims against the dealer or manufacturer of the eBike expire
or are constricted.
3
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
The eBike is subject to higher mechanical stress when operating at higher speed for
which it is not designed. This results in additional safety risks.
The installation and operation of the module is at your own risk. The manufacturer
accepts no liability for damage in connection with the installation or operation of
the unit.
Please inform yourself about possible further technical and legal consequences
before installing the device.
Technical Data
Housing dimensions: 37mm x 19mm x 9mm (1.46”x 0.75”x 0.36”)
Cable length: approx. 180mm (7”)
Weight: 0,025kg (0.9oz)
Power consumption: 0,2W
Supply voltage: 12VDC
Installation example Cube Reaction Hybrid Pro 500 / Bosch Performance CX 2020
Required tools:
Allen key 4mm
Procedure:
1. Remove battery
2. Remove the motor cover (Allen key 4mm).
4
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
Depending on the bike model, the engine cover can also be attached
with Torx or Phillips screws.
With many covers it is also necessary to remove the crank. A suitable
crank puller is required for this.
3. Disconnect the cables at the green marked two sockets. Also, use the following
sketch as a guide for different motors. Remove the green marked connectors.
Attention!
Also pay attention to the color of the small connector.
Black: rear light
Blue: front light
Gray: speed sensor
5
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
4. Connect the tuning module to the free sockets on the engine. Connect the previously
disconnected cables to the other connections of the tuning module.
5. Ensure that all connectors are fully inserted.
6. Write down the article number (P/N) and serial number (S/N) on the back of this
manual to have the data ready for possible support requests.
7. Insert the battery and carry out the initialization, see separate point “setup”(page 7).
8. If an individual activation code is to be set to protect the tuning from unauthorized
use, set it now, see point "Activation code" (page 11), otherwise continue in the next
step.
This point is optional. If you don't want to set a code, go to the
next step.
6
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
9. Remove the battery again.
10. Place the tuning module in a suitable location and route the cables so that the
reassembly of cover is possible. In the picture, the module was pushed into the down
tube.
Due to the large number of different drive systems and covers,
it is not possible to define a fixed installation location. Often a
placement of the module directly in the connection area of the
motor is possible. A placement in the frame tube is also
possible, but in this case the motor must mostly be dismounted
from the frame.
11. Reassemble cover.
12. Activate the tuning as described in the chapter "speed mode" (page 9).
7
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
Setup
Before the first use of the tuning module or after moving it to another bike the setup must
always be carried out first. Even in the case of malfunctions, the initial state of the module
can be restored by executing the setup.
The following illustrations show the Purion display. For the Nyon, Kiox or
Intuvia, press the corresponding buttons on the control unit.
Please set the display to km/h before. If set to mph you get different
readings during setup.
If an activation code is set, enter it now, otherwise continue.
Input example:
Code 32: press 3x “minus”, afterwards 2x “plus”.
Code 3: press 3x “plus”.
No code is set when new. Code is not displayed during input. Enter the
code quickly and proceed immediately to the next step. If you make a
mistake, wait 5 seconds before trying again.
3-5s
km/h
Press “minus”for 3 to 5 seconds.
Release “minus”button and within one second, press “plus”for 3
to 5 seconds.
Speed 11.1 km/h is displayed for 10 seconds.
Adjustment factor speed limit. Only adjust if there are problems,
see FAQ. If necessary, change within 5 seconds using the “plus”and
"minus" buttons. Possible values: 7.0..13.0 (= 70..130%). Default
value: 100%.
km/h
5s
km/h
3-5s
km/h
10s
km/h
8
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
If the display changes from 11.1 directly to 0.0, the wiring of the module is
faulty. The 2-pin connector to the motor is connected to the wrong socket.
Set the factory speed limit here or activate the workshop mode.
If necessary, change within 5 seconds using the “plus”and “minus”
buttons. Possible values: 20, 25, 32 (=20mph) and 45km/h, Default
value: 25.0. Set 1.0 for the workshop mode.
For a European e-bike, the factory speed limit is normally 25km/h. You do
not need to press anything in this case.
If you set a value that is too high, the tuning will not work. If the bike
supports up to 25km/h ex work you have to set 25km/h here.
As soon as setup displays 0.0 km/h, the setup is finished.
km/h
km/h
5s
9
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
Speed Mode
When speed mode is activated, the speed limit for the motor assistance is increased. The
limit can be set from 25
1
to 99 km/h (15.51to 61.5mph).
Turning off the eBike automatically turns off speed mode and must be reactivated after the
bike is turned on.
If the limitation is not removed despite being activated, the wrong eBike
type was set during setup. For eBikes that support up to 25 km/h without
tuning, the eBike type must also be set to "25".
Enable speed mode –No activation code set
Press "minus" for > 3 seconds while standstill or while driving.
Speed limit is displayed for 5 seconds. If desired, use the "plus" and
"minus" buttons to change. Possible values: 251to 99 km/h (15.5 to
61.5mph). Default value: 32 km/h (19.8mph). Set value will be
stored.
Display shows the normal driving speed again. Speed mode is
active.
Disable speed mode
Press "minus" for > 3 seconds.
Display shows the factory speed limit for 2 seconds. Speed mode is
off.
1
The lowest possible value is always the factory speed limit set during setup.
2s
km/h
5s
km/h
km/h
km/h
km/h
10
1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3
Enable speed mode –Activation code set
Enter the activation code. Always press the minus keystrokes first,
then the plus keystrokes.
Input example:
Code 32: press 3x “minus”, afterwards 2x “plus”.
Code 3: press 3x “plus”.
Code is not displayed during input. Enter the code quickly and proceed
immediately to the next step. If you make a mistake, wait 5 seconds
before trying again.
Press "minus" for > 3 seconds.
Speed limit is displayed for 5 seconds. If desired, use the "plus" and
"minus" buttons to change. Possible values: 25
1
to 99 km/ h (15.5
to 61.5mph). Default value: 32 km/h (19.8mph). Set value will be
stored.
Display shows the normal driving speed again. Speed mode is
active.
1
The lowest possible value is always the factory speed limit set during setup.
5s
km/h
km/h
km/h
km/h
Otros manuales para VOLspeed
1
Otros manuales de Accesorios para bicicletas de TLI
Manuales populares de Accesorios para bicicletas de otras marcas
Sigma
Sigma BC 16.16 Manual de usuario
Playcore
Playcore Dero Setbacks Manual de usuario
VDO Cyclecomputing
VDO Cyclecomputing x3dw Manual de usuario
Cateye
Cateye RAPID X2 Manual de usuario
buratti meccanica
buratti meccanica Clorofilla Trail Manual de usuario
Shimano
Shimano SG-8R20 Instrucciones de funcionamiento
