TKB Home TZ75 Manual de usuario

-1-

TZ75 Roller shutter controller

Note: This module must be“Included in the network”,and suitable for where it will be

permanently installed. The proper operation of this node in the mesh network is

dependent on it knowing it’s location with respect to other nodes. You can not "test

bench" configure this module, then install.

In the front casing, there is an on/off button with LED indicator which is used to

toggle switch on and off or carry out inclusion, exclusion, reset or association.

When first power is applied, its LED flashes on and off alternately and repeatedly

at 1-second intervals. It implies that it has not been assigned a node ID and can not

work with Z-Wave enabled devices.

The table below lists an operation summary of basic Z-Wave functions. Please

T M

refer to the instructions for your Z-Wave certificated primary co ntroll e r to

access the setup function, and to include/exclude/associate devices.

The in-wall Roller Shutter Controller is designed to switch rise/lower roller shutter

connected to its terminals using radio waves, controllers and a push button directly

connected to this Roller Controller.

The in-wall Roller Shutter Controller is a transceiver which is a Z-Wave enabled

device and is fully compatible with any Z-Wave enabled network. Slim design let

the Controller can easily hide itself into the wall box and that will be good for the

house decoration.

The new smart relay calibration technology can reduce the inrush current caused by

the load and let the module work perfectly with many kind of Roller Shutter. This

in-wall Roller Shutter Controller is able to detect position of the Shutter by using the

patterned power measuring method, so it can be remote controlled not only fully up

or down , but also can be adjusted to ex. 30% or 50%. And when manual controlled

by push button, the controller also can memorize the position and send the new shu

-tter position to its controller (ex. IP-Gateway).

-2-

To distinguish what mode the TZ75 is in, view from the LED for identification.

No matter up or down, close or open, Led will flash every two seconds while

Motor activate.

Under normal operation, when the TZ75 has not been allocated a node ID,

the LED flashes on and off alternately at 1-second intervals. By pressing S1

S2 or Include button, it will stop flashing temporarily. However, after discon

LED Indication

Group 1:lifeline

2. There are two groups for the switch

Each group can associate max five devices.

(Profile MSB=0x00,Profile LSB=0x01)

ID is excluded

-nect and reconnect the TZ75, the LED will flash on and off alternately at 1-

second intervals.

When overload state occurs, the TZ75 is disabled of which LED flashes on

and off alternately at 0.5 second intervals. Overload state can be cleared by

disconnect and reconnect the TZ75 to the main power .

Installation and operation

1. put the in wall TZ75 into a wall box and connect the AC power wire L, N to

TZ75 connector L, N.

2. Connect the wall switch to the TZ75 .

3.It is important to carry out a shutter calibration process before you control the

shutter to move. Press inclusion button over 3 seconds and release before the

6th second, the roller shutter controller will start the shutter calibration process.

The process is composed of three continue stages. The shutter move to the TOP

in first stage, and move to the BOTTOM in second stage, and move to the TOP

again in third stage. Then TZ75 will know the total range of UP and DOWN.

4.During the shutter calibration process, any emergencies happen you can press

and release the include button to stop the process.

5.If user found the direction is reverse, this may because the wrong connection

of NO1 and NO2 to the motor, please change NO1 and NO2 connection and exe-

cute calibration process again.

6.To manually switch up and down of the shutter, simply press S1 or S2 .

7.TZ75 built in meter function and can read the Watt , KWh, V(Voltage), I(Current) ,

PF(Power Factor) of the load by using Z-Wave command class.

8.TZ75 have overload protection function, and can help to prevent short circuit

caused by load.

Z-Wave Configuration

Watt Meter

Report period

KWH Meter

Report period

Threshold of Watt

for load caution

Threshold of KWH

for load caution

Configuration

Parameter Dedault

Unit

Value

Size

(Byte)

Function Description

0x01-

0x7FFF

0x01-

0x7FFF

10-1100

0-10000

5s 720

10min 6

1Watt 1100

Kwh 0

5*720s=3600s=1hour

6*1min=1hour

Watt Meter Report Period:

If the setting is configured for 1hour (set value =720), the TZ75 will report its

instant power consumption every 1 hour to the node of correspond Group. The

maximum interval to report its instant power consumption is 45 hours (5s*32767

/3600=45hr). Default value is 1 hour

KWH Meter Report Period:

If the setting is configured for 1hour (set value =6), the TZ75 will report its Accu-

mulated Power Consumption (KW/h) every 1 hour to the node of correspond

Group. The maximum interval to report its Accumulated Power Consumption

(KW/h) is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour

-3-

-4-

Threshold of Watt for Load Caution

This is a warning when the wattage of load over the preset threshold value,

If the setting value is 1100, when the load wattage over this value, TZ75 will

send Watt Meter Report command to the node of correspond Group. Default

value=1100W.

Threshold of KWh for Load Caution

This is a warning when the KWh of load over the preset threshold value, If

the setting value is 10000, when the Accumulated Power Consumption of

Relay1 or Relay2 over this value, TZ75 will send KWh Meter Report comma-

nd to the node of correspond Group, minimum value is 1KWh and default

value is 0kWh.It means no warning when the KWH of load over the preset

threshold value and not send KWH Meter Report.

Z-Wave Supported Command Class

COMMAND_CLASS_SWITCH_BINARY

COMMAND_CLASS_BASIC

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_VERSION

COMMAND_CLASS_ASSOCIATION

COMMAND_CLASS_METER_V3

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Troubleshooting

Sympton Cause of failure Recommendation

The TZ75 not working

and LED off

1. The TZ75 is not connect

to the Main power

2.The TZ75 break down

The shutter move direction is reverse

1. Check power connections

2. Don’t open up the TZ75

and send it for repair.

Wrong connection of NO1

and NO2 to the motor

Swap the NO1 No2

connection

Tz75 LED light work fine

But can not control

1. No association setting

2. Same frequency

interference

1. Carry out association

2. Wait for a while to re-try

Resistive Load 1100W/600W(EU/US) max

110~240VAC

Operating Voltage

Maximum Load

Range

Operating Temperature

Frequency Range

0℃~40℃

Specifications subject to change without notice due to continuing product.

868.4MHz(EU) 908.42MHz(US) 921.42MHz(AUS)

Minimum 40m in door 70m outdoor line of sight

Specification

TZ75-V1.0-2017.3.21

-5-

Warning:

1.Do not dispose of electrical appliances as unsorted municipal waste , use separate

collection facilities.

2.Contact your local government for information regarding the collection systems available.

3.If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak

into the groundwater and get into the food chain, damaging your health and well-being.

4.When replacing old appliances with new one, the retailer is legally obligated to take back

your old appliance for disposal at least for free of charge.

Limited Warranty:

Product is warranted against defects in material and workmanship for one year. We will

replace it free of charge and does not issue any refunds. This warranty extends only

to wholesale customers who buy through our Corporation authorized distribution channels.

Our Corporation does not warrant this product to consumers.

This warranty does not apply to:

(a) damage to units caused by accident, dropping or abuse in handling, or any negligent use.

(b) units which have been subject to unauthorized repair, taken apart,or otherwise modified.

(d) damages exceeding the cost of the product.

(e) transit damage, initial installation costs, removal cost, or reinstallation cost.

Wiring diagram

Product size (mm)

L: Line voltage input

NO1,NO2: motor connector

N: Line neutral

S: Connect to wall switch input

Otros manuales de Controladores de TKB Home

TKB Home

TKB Home TZ75 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario