Tinycontrol LANKONT-001 Manual de usuario

Firmware version 3.21 –„HOME”

LAN Controller

manual

manual v. 3.21 HOME – LAN Controller – LANKONT-001

LAN Controller

LAN controller is a simple, but innovative device which has long been lacking in the mar-

ket network solutions. A small board serves as a web server which presents the various

sensor readings and allows you to remotely control up to 5 outputs. Additionally Events

Cong feature allow you to program the appropriate action when sensor readings met

certain conditions. ISP can use watchdog function, it check the ping up to 5 network de-

vices, and if no response runs the relays. Useful for many applications can be a Scheduler,

that allows the on / othe device at a specied time or for a specied period of time.

There is also PWM output to control brightness of light or an electric motor speed. For far

rom socket installation board could be powered by passive PoE. Few versions of rmware

is available today, each is developed and after publication customer could upgrade it by

preapred software. In Accessory are presented all sensors and upgrade kits compatible

with Lan Controller.

Examples of applications

ISP

ttemperature, supply voltage and person occupancy control in server rooms

tweather condition report on the occasion of IP cameras views

Home control

thome electric stove control (automatically or remote)

tturning on/ohome lightening remote, by scheduler or by event, controlling intensity

tturning oTV box if remote is other person hands ;-)

tirrigation control - you don’t need visit your garage to modify irrigation time or you can

turn sprayer precisely in the moment when your favorite neighbor passes near ;-)

Home installations

ttemperature controlling and simple automation in your heating system

ttemperature and pressure controlling in solar thermal installations

tmeasurements of heat pump operation

tmonitoring of grid voltage and automatic switching to backup with mail notication

tremote control (by LAN or wirelesslan) understands as forwarding command to one of

output of Lan controller from input of other Lan controller

Renewable energy

tmeasurements of solar cells work

tmeasurements of wind turbines

tmeasurements of charging battery

tmeasurements of power consuming

manual v. 3.21 HOME – LAN Controller – LANKONT-001

RESTARTER, MONITOR, CONTROLLER

FEATURES:

tWWW or SNMP v2 management

trmware upgrade via TFTP

tread data in real time without refreshing page

tpossibility switch on/oto 5 relay direct from page WWW

tevents panel to self-programming by user

tScheduler (switch on/ooutput for denite time in week days)

tmonitoring additional devices eg. PIR sensors

tenvironmental temperature and supply voltage on board measurement

ttemperature and current measurement from connected sensors

tpower measurement for DC voltage

tpossibility to connecting of the additional boards: with 4 switched PoE ports or 4 relays

tset time manualy or by server NTP

tposisibility sensors calibration

tfrequency and duty modied PWM output

tremote control: each output of Lan controller setup as server can be controlled remo-

telly by LAN network from inputs of others Lan controllers

te-mail notication about programmed events

tSNMP TRAP notication about programmed events

tHTTP client: GET, POST notication

tautomaticaly send state or value inputs to SNMP server

timplemented protocols: HTTP, SNMP, SMTP, SNTP, ICMP, DNS, DHCP

tsupported temperature sensors: NTC10K B=3950, KTY-84, PT1000

tpower measurement from pulse meters DTH22 humidity sensor support

tsupport for monostable/bistable wall switches for lighting control

thttp client for send data to remote IoT servers like www.thingspeak.com

tno watchdog

Default user and password is„admin”, IP adress is 192.168.1.100

manual v. 3.21 HOME – LAN Controller – LANKONT-001

TECHNICAL SPECIFICATIONS

tsupply voltage: 8÷56V

tpower consumption : about 1W

tPoE supply: YES, passive

tProtection from wrong supply polarization: YES

tinterface: ethernet 10Mbit/s

trelay: 255VAC 10A

toperating temperature: –20 do +85 °C

tweight 45g (without casing)

tcasing type Z-67 (not included)

tdimensions 57x67mm

INPUT/OUTPUT:

t1 RELAY to switch on/oanother devices, available contact: NC and NO

t4 OUTPUT to switch relays, ports PoE or another devices;

t1 CONFIGURABLE PWM OUTPUT from 2,6 KHz to 4Mhz;

t4 LOGICAL INPUT (max 12V): to monitoring another devices, eg. bufor supply. colla-

boration with outputs: OC,NO, NC

t5 ANALOG INPUT:

INP1: temperature measurement witch thermistor NTC 10K B=3950 (from –40 to +120 °C)

or thermistor KTY-84-130 (from –40 to +300°C), accuracy 1°C (dependent on NTC)

INP2: thermistor NTC 10K or voltage mesurement to 3,6V, with use additional divider

increase range.

INP3: voltage measurement to 35V, accuracy ± 0,1V;

INP4: temperature measurement by PT1000 (from –20 to +350 °C) accuracy ± 2°C;

INP5: measurment DC current to 3A, accuracy ± 10mA;

t1-WIRE BUS (RJ11 connector) to input sensor DS18B20 - max 6 sensors

manual v. 3.21 HOME – LAN Controller – LANKONT-001

PINS and COMPONENTS DESCRIPTION

Temperature board sensor. Ethernet

10Mbit.

PIN/Component Description

Power Power suplly 8V÷56VDC or via PoE

RELAY bond To connect external device, detail description below

LED1 Shine LED means Power on board

LED2 Shine LED means relay active

IDC10 To connect additional board, detail description below

INP1D Logical input 1

GND1 gnd for INP1D and INP2D or general gnd

INP2D Logical input 2

GND2 general gnd

+3,6V Supply for sensors NTC-10K and KTY-84 connected to INP1 or INP2

INP1 input for sensor NTC-10K or voltage measurement max (without divider ) 3,6V

INP2 input for sensor NTC-10K or KTY-84-130

INP3 input for voltgae measuerment max 35V

GND3 general gnd

INP4 input for sensor PT1000 or connected the same sensor in solar controller

INP5 Input for current measurement

GND4 Gnd for current measurement Or general if don’t measurement current

INP6 input for sensor DS18B20 (1-Wire bus on the connector RJ11)

INP3D Logical input 3

INP4D Logical input 4

GND5 gnd for INP3D and INP4D or general gnd

RESET button,

change relay

state and do

sets reset

Relay bond

(output OUT0)

IDC10

INP1D

GND1

INP2D

GND2

+3,6V

INP1

INP2

INP3

GND3

INP4

INP5

GND4

Power

LED 1

LED 2

INP6 - RJ11

1-Wire bus

for DS18B20

GND5 INP4D INP3D

manual v. 3.21 HOME – LAN Controller – LANKONT-001

Relay Bond:

NO – contact normaly open

CON – common contact

NZ – contact normaly closed

ATTENTION: In spite of that relay can switch AC voltage 255VAC 10A, board fail to com-

ply with safety requirements (lack housing, earthing). Therefore that receiver connect

with the assistance safety external relays eg. on DIN bus, controlled by relay on board.

IDC10 and 1-Wire:

1 – analog input not use 2 – analog input not use

3 – +3,6V 4 – OUT4

5 – GND 6 – OUT3

7 – PWM output 8 – OUT2

9 – VIN, vcc suplly 10 – OUT1

Reset button

Push about 0,5 second cause change relay state on opposite, push and keep longer about

5 second (if we not logged by WWW on modul) cause modul reset, next if you still keep

button about 10 second cause set all settings to default. Set all settings to default conr-

mation is fast switch relay on/o(klik-klik), don’t wrong this with change relay state about

0,5s and switch relay oafter restart.

User and password: admin

IP: 192.168.1.100

1 2

9 10

GND 1-Wire not

use VCC=3.6V

RESET

ETHERNET

10 Mbit

NO CON NZ

manual v. 3.21 HOME – LAN Controller – LANKONT-001

SENSORS CONNECT

1. Current measurement

2. Temperature measurement and logical input

GND4

–

Power

receiver

max 3A

VCC

–

Power

supply

INP4

GND3

INP2D

GND1

INP1D

PT-1000

INP2

INP1

+3.6V

NTC-10K

or KTY84

NTC-10K

manual v. 3.21 HOME – LAN Controller – LANKONT-001

3. Voltage measurement

Additional resistor to increase measure range INP1

R = 10K increase range 2 (multiplier 2) that is 3.6V x 2 = 7.2V

R= 20 K increase range 3 (multiplier 3)

R= 30 K increase range 4 (multiplier 4) etc.

Add resistor must be connected with set proper multiplier in eld VCC on control panel

page.

INP3

GND3

INP1

GND2

INP1 is use to temperature

measure or voltage,

in control panel you must

choice what you want

measure

INP1

Measure voltage

max 3.6 V DC

or more if you

add divider

resistor

Measure voltage

max 35 V DC

Measure

voltage

multiplier

manual v. 3.21 HOME – LAN Controller – LANKONT-001

4. DHT22 sensor and pulse output from the counter

Despite of connected sensors, inputs INP4D and INP3D can still be used as a standard di-

gital inputs in an array of events, just for the DHT11 at INP4D closed to ground will not be

correct read and the shorting INP4D will calculate extra impulses.

–

output terminals

of the meter pulse energy

for dierent counters

may dier markings

20 21

VCC=3.6V

GND5

INP4D INP3D

manual v. 3.21 HOME – LAN Controller – LANKONT-001

Management by WWW.

1. Control Panel

Any descrip-

tion of the

measured

physical

quantity,

such as kWh,

L/min, etc.

Negation for

digital input

for Even Con-

g tripping

Divider pulse counter

- for example as ours

energy meter sends

1000 pulses per

1 kWh is enter 1000,

as it sends 1600 pulses

enter 1600, etc.

Choice

of voltage

input for power

calculation

Multiplier of PWM

duty used for INP1

Even Cong table

tripping.

Test input - in the current

rmware version 3.21 - unused

Change outputs

state display

Any text

description,

max 8 chars

Reset time – „0” for normal

outputs work (ON/OFF) ,

for time > 0 output change

state and return to state be-

fore after the specied time

in seconds (max 65534).

Value of calibration

- adds to or subtracts

the desired value

Choice type

connected

sensor

click cause

change relay

state on opposite

(OUT0 relay on

board)

automatic socket

arming at xed

time (two panes:

one - time arming,

second - break

time)

Set State

All output

simultaneously

according to

combo box

Run PWM genera-

tor (when chan-

ging frequency or

ll does not need

to turn othe

generator)

Run Power

measure from

INP3 (voltage)

and INP5 (current)

Tabla de contenidos

Otros manuales de Controladores de Tinycontrol

Tinycontrol

Tinycontrol tinyESP Manual de usuario

Tinycontrol

Tinycontrol Lan Controller v3 Manual de usuario

Tinycontrol

Tinycontrol GSMKON-030 Manual de usuario

Tinycontrol

Tinycontrol LAN Controller V2.0 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario