Note that: If you select a color output, such as red, then you select another color output , such as green. So red
and green are output at the same time. If you only need to separate out the second output “green”, just turn off
the front color “red”.
Attention: The receiver is under single or multi-color adjustment condition when any single or multi-color is
selected. Under this condition, you can only make clockwise rotation or counterclockwise rotation
operation to adjust the color. A direct touch on color wheel will not work. Only after exiting from the single or
multi- color condition, a direct touch on color wheel will work.
In short, using R, G, B, W buttons and operating color wheel ,you can mix more than 100
million colors or any color you want.
Attention: The receiver ID learned by touching color wheel is different from the reciever that learned by
pressing function button .The receiver ID learned by touching color wheel that we define
it as SLAVE receiver, the receiver ID learned by pressing function button that we define it as
MASTER receiver. The purpose of learning these two kinds of receivers is to ensure the receivers and color
changing synchronously to avoid the color changing out of order. This point will be noted later.
3. Delete ID and ID re-learning
If you need to delete the ID learned in the receiver, press ID learning button for more than 5 seconds, when
learning indicator is off, then the learned ID is deleted. If you need the receiver learn a new ID, repeat the
operation of 4.2 (Receiver learning ID).
4. Choose color by touching color wheel
After the receiver learned the ID, you can change each receiver’s color by touching color wheel. If you want to
change the color of receiver NO.1.. Press button ,then make rotating touch on color wheel by your
figures, at this time, the color of receiver No.1 will be changed constantly , when your favorite color appears,
stop rotating and leave the color wheel .
If you need change color of several receivers at the same, just choose a number for these several receivers
first, then touch color disc .For example, change color for receivers NO.1, 2, 3,4,5,6
at the same time, you need press number 1 to 6 button first, then touch the color wheel .
1
5. Select or adjust color by R, G, B, W button
In addition to change the color by touching color wheel ,but you can also select the single color through
R,G, B, W buttons or adjust the color by color wheel to get your wanted color. For example, you
choose a color by touching color wheel and still want add a bit more brightness to red color, just press R
button for over 2 seconds, then the indicator of R will be on and red is selected, make clockwise rotation
on the color wheel by finger, then the brightness of red will be increased. If you want the red color to be
darker, just make counter clockwise rotation on the color wheel . If need to adjust the color brighter or
dim several colors at same time, also just choose the colors , such as R,G, then make clockwise rotation
or counterclockwise rotation ,it can simultaneously adjust the brightness for both colors. If you want to
cancel the selected color, just press selected button for 2 seconds, the corresponding color will be off, this color
is abandoned.
By pressing of R ,G, B, W button ,you can turn on/off the corresponding single color. For example,
if you want LED lightings to get red, press R for over 1 second, then the red color will be turn on. If you want
to turn off red again, press R for 1 second, the red will be off again. The same operation is for other colors.
R G B W
R
R G B W
R G B W
R
R
R G B W
6. Choose color changing mode
Selecting the mode button ,receiver change colors according to different modes, a total of 10 built-in color
changing modes. If you want one or several receivers under color changing mode,
press number button ,and choose receiver number, then press button again. For first press of
button ,receiver will change according to mode 1, one more time press of button ,the receiver will be
paused, it will stay at one color under mode 1 condition. Press button again, the color will change according
to mode 2, press button one more time , it will be paused at one color under mode 2. Press button for
seconds, the receiver will keep changing as follows:
M
7. Brightness adjustment
Under the static color status or color changing status, you can adjust the brightness by press B and pressing
button to increase the brightness. The brightness is divided into 8 levels, the minimum is 10%, and the
maximum is 100%.
B+
8. Changing speed adjustment
Under color changing mode, you can slow down the changing speed by pressing button ,or speed up
changing speed by pressing button , 16 speed levels in total are available. The maximum changing cycle is 4
seconds; the minimum changing cycle is 256 seconds.
S-
S+
B-
S- S+ MB- B+
S- S+ MB- B+
1 2
3456
1 2
3456
78 9 10 M
MM
M
MM
MODE1－STOP---MODE2---STOP---MODE3---STOP---MODE4---STOP---MODE5---STOP---MODE6---STOP-
--MODE7---STOP---MODE8---STO
P---MODE9---STOP---MODE10---OFF---MODE1......
The receiver will be at one of static colors by touching the color wheel in color changing modes. Then press M
button , receiver will be changed as Mode 1 again.
Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Think
ahead
ESC
GmbH
I
Anzengruberstr.
39
I
A-9020
Klagenfurt
a.
W.
I
T
+43
(0)463
21
09
46
I
[email protected] I
www.think-ahead.at
