Thermotouch 4.3dC Manual de operación

Installation & User Guide

Dual Control Thermostat

Thermotouch 4.3dC

DUAL CONTROL SYSTEM

5245 / 5246

Contents

Compatibility ............................................................... 3

What’s in the box? ....................................................... 4

Before you start ........................................................... 5

Installing Thermotouch .................................................. 6

Wiring diagram ............................................................ 9

User interface .............................................................. 11

Set the time and date ................................................... 12

Heating schedule ......................................................... 13

Appliance controls ........................................................ 19

Heating modes ............................................................ 20

Settings ...................................................................... 22

Compatible sensor probes ............................................. 24

Technical data ............................................................. 25

Compatibility

Thermotouch 4.3dC is compatible with almost all

electric underfloor heating (UFH) systems available.

Thermotouch can replace your existing underfloor

heating thermostat and is compatible with many of

the most popular thermostat brands’ floor sensor

probes including those rated at:

• 6.8kΩ@ 25°C

• 10kΩ@ 25°C

• 12kΩ@ 25°C

• 15kΩ@ 25°C

• 33kΩ@ 25°C

Replacing an existing thermostat?

Contact the manufacturer’s technical department

and ask for the rating of the floor sensor at 25°C.

What’s in the box?

Check you’ve got everything:

• Thermotouch 4.3dC thermostat

• Floor sensor probe (3m)

• Floor sensor conduit (3m)

• Fixing screws

• Manual and warranty information

You will also need:

• Electrical screwdrivers

• Deep electrical back box

• Electric testing meter

Before you start

Thermotouch 4.3dC should be:

• Installed 1.2 - 1.5m from the floor

• On an interior wall

• In an area outside any wet zones (IP30)

• Installed on an RCD protected circuit

• Away from drafts or heat influences

• Installed so that the floor sensor probe

can be laid in a clear, temperature

representative area of the floor.

• In an open area of the room

• Installed by a professional, in line

with current IEE 17th Edition Part P

regulations and local standards.

Installing Thermotouch

1. Switch off mains power

You will be installing Thermotouch as part

of a high voltage mains electrical circuit.

To ensure your safety and to protect the

thermostat, switch off the mains power

before you start the installation.

Fuse Box Fused Switch

CAUTION

High Voltage

Cables

Installing Thermotouch

2. Choose a location

At this stage it its likely that an electric

underfloor heating system has been

installed and a back box is already in place.

The underfloor heating cold tail should

be pulled up through the back box, and

the sensor probe installed (in the conduit

provided) within the wall cavity or pre

chased channel in a solid wall.

Installing Thermotouch

3. Maximum distances

Thermotouch can be installed up to 50m

away from the underfloor heating system it

is controlling, provided that the floor sensor

is used to control the temperature.

Underfloor heating cold tails and floor

sensor probes can be extended up to 50m.

50m max.

Installing Thermotouch

UFH Live

UFH Neutral

Appliance Neutral

230V AC Supply Neutral

230V AC Supply Live

Appliance Live

Common Earth (Ground)

Sensor connections

4. Wiring diagram

Connect Thermotouch to the underfloor heating

(UFH) cold tail, additional appliance, power

supply and floor temperature sensor.

The floor temperature sensor is not polarity sensitive.

987654321

Installing Thermotouch

5. Fix to the wall

Use a small flat screwdriver in the groove

on the underside to lever the face plate

away from the back plate.

Carefully disconnect the ribbon cable and

align Thermotouch with the mounting

positions on the pre installed back box.

Fix in place with the screws provided. Now

connect the ribbon cable and clip the face

plate back into position.

Otros manuales para 4.3dC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de thermotouch

thermotouch

thermotouch 7.6iG Manual de operación

thermotouch

thermotouch 5245W Manual de operación

thermotouch

thermotouch 5215 Manual de operación

thermotouch

thermotouch 5220W Manual de operación

thermotouch

thermotouch 4.3dC Manual de operación

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario