THERMOBILE IMAC 2000 PELLET Manual de usuario

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

THERMOBILE UK LTD

12, Buckingham Cl se

Bermuda Industrial Estate

Nuneat n, Warwickshire

CV10 7JT

Gr t-Brittannië

T +44 (0)2476 35 79 60

F +44 (0)2476 35 79 69

inf @therm bile.c .uk

www.therm bile.c .uk

THERMOBILE FRANCE sarl

3, rue Denis Papin

45240 LA FERTÉ ST. AUBIN

Frankrijk

T +33 (0)2 38 76 59 25

F +33 (0)2 38 76 58 93

inf @therm bile.fr

www.therm bile.fr

THERMOBILE INDUSTRIES V

K nijnenberg 80

4825 BD Breda Nederland

P stbus 3312

4800 DH Breda Nederland

Bedrijfsnummer: 3502

T +31 (0)76 587 34 50

F +31 (0)76 587 27 89

inf @therm bile.c m

www.therm bile.c m

THERMOBILE

IMAC 2000 PELLET

41.731.000

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Fig 1

Fig

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

MAX OPERATING DISTANCE

20M

1) CONTAINER 10ft

2) MAULWURF

3) PELLET SUCTION HOSE

4) HEATER

7) PELLETSTORAGE

CONTAINER

5) EXHAUST FAN

AIR HOSE

Fig 6

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Fig 8

Installation exhaust fan.

In case no external thermostat is used the

cap must be placed in the connector as

shown.

Mounting the ash auger. Positioning and mounting the ash bin.

Fig 7

Fig 10

Fig 11

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Air

Pellets

P wer Maulwurf

Air

Pellets

Refill c ntainer

Connecting the 10ft container to the temporary pellet storage

P wer t

maulwurf

Pellets fr m

10ft

c ntainer

Air t

10ft c ntainer

P wer

M unting the

Pellet slide

P wer pellet auger.

Pellet

Installation temporary pellet storage, connecting the Maulwurf, mounting the Pelletslide.

Fig 12

Fig 13

Fig 14

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Contents

Safety instructions 8

Introduction 9

Preparations and main components. 10

Operation 11

Maintenance. 11

Troubleshooting 12

Spareparts 13

Technical information 13

Installation of accessories 13

EC Declaration of conformity 13

APENDIX 14

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Preface

This manual contains the instructions for use of the convector heater shown on the cover.

The information in this manual is important for the correct and safe operation of the

convector heater.

Identification of the product (Fig. 1)

The identification plate is mounted on the side of the convector heater. The identification

plate contains the following information:

A Type of machine

B Production code

C Type of fuel

D Air output

E Net capacity (Hi)

F Voltage / frequency

G Current

H Fuel consumption

I Year of manufacture

J Serial number

Service and technical support

For information about the convector heater, please contact your dealer of the manufacturer.

Make sure you have the following information at hand: type and serial number of the

convector heater.

Warranty and liability

For warranty and liability, please refer to the general warranty conditions.

Environment

Note

The heater is made of various metals and synthetic materials. The heater also contains

electronic parts, which must be treated as electronic waste. Please contact your dealer for

further information.

Only applicable to the European Union

Waste disposal of electric & electronic equipment for business use.

For further information regarding the disposal of products for business use at the end of their

life span, please contact your dealer or distributor in your country. This product may not be

disposed of together with commercial waste or as commercial waste.

1 SAFETY INSTRUCTIONS

1.1 Pictograms used in the manual

Caution

Points to risk of damage to the equipment.

Warning

Points to a dangerous situation, which may result in death or serious injury.

Warning

Always switch off the power supply before carrying out any maintenance of repair work to the

convector heater!

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

Hot

Some surfaces may be hot! Wait until these parts have cooled down before carrying out any

maintenance.

Suggestions and tips to facilitate the necessary tasks or actions.

1.2 Lifting instructions (Fig. 2)

A Lifting hooks

B Shafts for lifting using a fork-lift truck

Warning

Do not use any unsuitable material for lifting the convector heater.

To find out the weight of the convector heater, refer to table C in the Appendix at the back of

this manual.

1.3 Icons on the burner (Fig. 3)

A Switch for manual turning on the ash auger.

B Burner connection

C Burner fixation

To take out the burner disconnect B and C.

1.4 Use this product for the purpose it was intended for

The convector heater was designed for the heating of tents, building sites, showrooms,

sports halls, storage sheds, workshops, round-the-clock projects, warehouses, greenhouses,

polytunnels, spray arrangements, and for the drying of agricultural produce and bulbs.

1.5 General instructions Warning

• Make sure to read this manual carefully before using the convector heater.

• Keep this document near the convector heater.

• Follow the procedures described.

• Do not lean on the convector heater.

• Keep at least 2 meters away from the exhaust opening of the convector heater.

• Make sure there is sufficient air for proper combustion.

• Make sure there is no highly flammable material near the convector heater.

• Make sure that the convector heater has cooled off sufficiently and that the plug has

been removed from the socket before carrying out any repair or maintenance work.

2 INTRODUCTION

2.1 Purpose

This convector heater is an indirectly fired heater with safety thermostat protection,

connections for a room thermostat, and a flue with rain cover.

The convector heater has been tested at sea level at a temperature of 20 C.

2.2 Working principle

Using the selection switch, the convector heater can be used in one of two ways:

• Position 1: the fan will switch on to supply ventilating air to the room only.

• Position 2: the burner will switch on, after which the fan will switch on as well, after a

short while. The hot air can be conveyed to the room to be heated by means of a system of

channels or tubes.

THERMOBILE INDUSTRIES BV

INSTRUCTIONMANUAL PELLETHEATER

A room thermostat can be connected to the control cabinet. It can be used to control the

temperature in the room to be heated.

The external auger transports the pellets from a pellet container to the burner. The controller

board contains a microprocessor system that tests main safety components, monitors and

regulates the burning procedure, starts and stops the burner automatically according to the

heater temperature. A warm air element (electrical igniter) ignites the pellets. The start

procedure is designed to create a quick and smoke free ignition.

The burner starts burning when the heater temperature cools down and heater thermostat

switches on. Burner runs until the pre-set maximum heater temperature (switch-off

temperature) has been reached. After that burner stops safely burning procedure and goes

to waiting (stand by) status.

Main supply interruptions (blackouts) are taken care of by the control system. After a main

supply interruption burner stops safely burning and goes to stopped status. When a blackout

occurs, the burner ends safely burning process. If there is a safety risk, the burner switches

off.

2.3 Main components of the convector heater (Fig. 5)

A Flue connection

B Lifting hook

C Operating panel

D Socket

E Identification plate

F Connection for room thermostat

G Socket for power connection

H Fan motor

I Air inlet

J Fan

K Burner room

L Heat exchanger

M Shaft for lifting purposes

N Ash auger motor

O Ash auger

R Burner

S Auger switch (fig.xx A )

T Hot-air outlet

U Armature nut

V Thermostat sensor

2.4 Burner (Fig. 3)

Make sure to read the burner Manual carefully before using the convector heater

With this heater is it is easy to take out the burner for cleaning and servicing. To take out the

heater disconnect B and unscrew C.

Tabla de contenidos

Otros manuales de Calentador de THERMOBILE

THERMOBILE

THERMOBILE AGA 111 Manual de usuario

THERMOBILE

THERMOBILE AT 306 Manual de usuario

THERMOBILE

THERMOBILE IMAC 4000 GAS US Manual de usuario

THERMOBILE

THERMOBILE IMAC 4000 Manual de usuario

THERMOBILE

THERMOBILE IMA Manual de usuario

THERMOBILE

THERMOBILE IMA US Series Manual de usuario

THERMOBILE

THERMOBILE IMAC 4000 OIL US Manual de usuario

THERMOBILE

THERMOBILE IFT-21 Manual de usuario

THERMOBILE

THERMOBILE ITA 30-US Manual de usuario

THERMOBILE

THERMOBILE TAS 800 Manual de instalación

THERMOBILE

THERMOBILE Bio Energy Series Manual de usuario

THERMOBILE

THERMOBILE BX 3 Manual de usuario

THERMOBILE

THERMOBILE ISA 65 Manual de usuario

THERMOBILE

THERMOBILE Bio Energy Series Manual de usuario

THERMOBILE

THERMOBILE Bio Energy 2 Manual de usuario

THERMOBILE

THERMOBILE IMAC Manual de usuario

THERMOBILE

THERMOBILE AT 400 Manual de usuario

THERMOBILE

THERMOBILE AGA 45 Manual de usuario

THERMOBILE

THERMOBILE AGA 100 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario