Thermal Dynamics CUTMASTER Manual de usuario

A-08621

380-

400

25mm

380-

400

20mm 60

AMP

380-

400

12mm 40

AMP

PLASMA CUTTING SYSTEM

25mm CUTMASTER™

Rev. AE Date: March 20, 2012 Manual # 0-5117

Operating Features:

Operating Manual

12mm

20mm

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Thermal Dynamics product. We

are proud to have you as our customer and will strive to provide

you with the best service and reliability in the industry. This

product is backed by our extensive warranty and world-wide

service network. To locate your nearest distributor or service

agency call 1-800-426-1888, or visit us on the web at www.

thermal-dynamics.com.

This Operating Manual has been designed to instruct you on the

correct use and operation of your Thermal Dynamics product.

Your satisfaction with this product and its safe operation is our

ultimate concern. Therefore please take the time to read the

entire manual, especially the Safety Precautions. They will help

you to avoid potential hazards that may exist when working with

this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and

Fabricators Worldwide.

Thermal Dynamics is a Global Brand of manual and automation

Plasma Cutting Products for Thermadyne Industries Inc.

We distinguish ourselves from our competition through market-

leading, dependable products that have stood the test of time.

We pride ourselves on technical innovation, competitive prices,

excellent delivery, superior customer service and technical

support, together with excellence in sales and marketing

expertise.

Above all, we are committed to developing technologically

advanced products to achieve a safer working environment

within the welding industry.

WARNING

Read and understand this entire Manual and your employer’s safety practices before installing, operat-

ing, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement, the

Manufacturer assumes no liability for its use.

Plasma Cutting Power Supply

CutMaster™ 12mm SL60 1Torch™ Operating Manual No.: 0-5117

CutMaster™ 20mm SL60 1Torch™ Operating Manual No.: 0-5117

CutMaster™ 25mm SL60 1Torch™ Operating Manual No.: 0-5117

Published by:

Thermal Dynamics Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

www.thermal-dynamics.com

Thermadyne Corporation

Reproduction of this work, in whole or in part, without written permission of the publisher is

prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or

damage caused by any error or omission in this Manual, whether such error results from negli-

gence, accident, or any other cause.

Original Publication Date: October 30, 2008

Revision Date: March 20, 2012

Record the following information for Warranty purposes:

Where Purchased:_________________________________________________

Purchase Date:____________________________________________________

Power Supply Serial #:______________________________________________

Torch Serial #:_____________________________________________________

TABLE OF CONTENTS

SECTION 1: GENERAL INFORMATION .................................................................................1-1

1.01 Notes, Cautions and Warnings...................................................................1-1

1.02 Important Safety Precautions .....................................................................1-1

1.03 Publications ................................................................................................1-2

1.04 Note, Attention et Advertissement ..............................................................1-3

1.05 Precautions De Securite Importantes .........................................................1-3

1.06 Documents De Reference ..........................................................................1-5

1.07 Declaration of Conformity ...........................................................................1-6

1.08 Statement of Warranty................................................................................1-7

SECTION 2 SYSTEM: INTRODUCTION ................................................................................2-1

2.01 How To Use This Manual ...........................................................................2-1

2.02 Equipment Identiﬁcation .............................................................................2-1

2.03 Receipt Of Equipment.................................................................................2-1

2.04 Power Supply Speciﬁcations ......................................................................2-2

2.05 Input Wiring Speciﬁcations .........................................................................2-3

2.06 Power Supply Features ..............................................................................2-4

SECTION 2 TORCH: INTRODUCTION ................................................................................2T-1

2T.01 Scope of Manual.......................................................................................2T-1

2T.02 General Description..................................................................................2T-1

2T.03 Speciﬁcations ...........................................................................................2T-1

2T.04 Options And Accessories..........................................................................2T-2

2T.05 Introduction to Plasma..............................................................................2T-2

SECTION 3 SYSTEM: INSTALLATION ..................................................................................3-1

3.01 Unpacking...................................................................................................3-1

3.02 Lifting Options.............................................................................................3-1

3.03 Primary Input Power Connections ..............................................................3-1

3.04 Gas Connections ........................................................................................3-2

SECTION 3 TORCH: INSTALLATION ...................................................................................3T-1

3T.01 Torch Connections....................................................................................3T-1

3T.02 Setting Up Mechanical Torch....................................................................3T-1

SECTION 4 SYSTEM: OPERATION.......................................................................................4-1

4.01 Front Panel Controls / Features..................................................................4-1

4.02 Preparations for Operation .........................................................................4-2

SECTION 4 TORCH: OPERATION........................................................................................4T-1

4T.01 Torch Parts Selection ...............................................................................4T-1

4T.02 Cut Quality................................................................................................4T-2

4T.03 General Cutting Information......................................................................4T-2

4T.04 Hand Torch Operation ..............................................................................4T-3

4T.05 Gouging ....................................................................................................4T-6

4T.06 Mechanized Torch Operation ...................................................................4T-8

4T.07 Parts Selection for Manual and Mechanized Torch Cutting......................4T-9

4T.08 Recommended Cutting Speeds for Mechanized Torch With Exposed Tip4T-10

4T.09 Recommended Cutting Speeds for Mechanized Torch With Shielded Tip4T-13

PATENT INFORMATION .....................................................................................................4T-16

TABLE OF CONTENTS

SECTION 5 SYSTEM: SERVICE.............................................................................................5-1

5.01 General Maintenance .................................................................................5-1

5.02 Maintenance Schedule ...............................................................................5-2

5.03 Common Faults ..........................................................................................5-2

5.04 Fault Indicator.............................................................................................5-3

5.05 Basic Troubleshooting Guide......................................................................5-4

5.06 Power Supply Basic Parts Replacement ....................................................5-6

SECTION 5 TORCH: SERVICE.............................................................................................5T-1

5T.01 General Maintenance ...............................................................................5T-1

5T.02 Inspection and Replacement of Consumable Torch Parts .......................5T-2

SECTION 6: PARTS LISTS......................................................................................................6-1

6.01 Introduction.................................................................................................6-1

6.02 Ordering Information...................................................................................6-1

6.03 Power Supply Replacement .......................................................................6-1

6.04 Replacement Power Supply Parts ..............................................................6-2

6.05 Options and Accessories............................................................................6-2

6.06 Replacement Parts for Hand Torch ...........................................................6-3

6.07 Replacement Parts - for Machine Torches with Unshielded Leads ............6-4

6.08 Replacement Shielded Machine Torch Leads Assemblies ........................6-6

6.09 Torch Consumable Parts (SL60) ................................................................6-7

6.10 Torch Consumable Parts (SL100) ..............................................................6-8

APPENDIX 1: SEQUENCE OF OPERATION (BLOCK DIAGRAM)....................................... A-1

APPENDIX 2: DATA TAG INFORMATION ............................................................................ A-2

APPENDIX 3: TORCH PIN - OUT DIAGRAMS...................................................................... A-3

APPENDIX 4: TORCH CONNECTION DIAGRAMS .............................................................. A-4

APPENDIX 5: SYSTEM SCHEMATIC, 380/400V UNITS ...................................................... A-6

APPENDIX 6: Publication History........................................................................................... A-8

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION ...................................Rear Cover

This page intentionally blank.

CUTMASTER 12mm, 20mm, 25mm

Manual 0-5117 1-1 GENERAL INFORMATION

SECTION 1:

GENERAL INFORMATION

1.01 Notes, Cautions and Warnings

Throughout this manual, notes, cautions, and warnings are used to

highlight important information. These highlights are categorized

as follows:

NOTE

An operation, procedure, or background information

which requires additional emphasis or is helpful in

efﬁcient operation of the system.

CAUTION

A procedure which, if not properly followed, may cause

damage to the equipment.

WARNING

A procedure which, if not properly followed, may cause

injury to the operator or others in the operating area.

WARNING

Gives information regarding possible electrical shock

injury. Warnings will be enclosed in a box such as this.

1.02 Important Safety Precautions

WARNING

OPERATION AND MAINTENANCE OF PLASMA ARC

EQUIPMENT CAN BE DANGEROUS AND HAZARDOUS

TO YOUR HEALTH.

Plasma arc cutting produces intense electric and

magnetic emissions that may interfere with the proper

function of cardiac pacemakers, hearing aids, or other

electronic health equipment. Persons who work near

plasma arc cutting applications should consult their

medical health professional and the manufacturer of

the health equipment to determine whether a hazard

exists.

To prevent possible injury, read, understand and fol-

low all warnings, safety precautions and instructions

before using the equipment. Call 1-603-298-5711 or

your local distributor if you have any questions.

GASES AND FUMES

Gases and fumes produced during the plasma cutting process can

be dangerous and hazardous to your health.

• Keepallfumesandgasesfromthebreathingarea.Keepyour

head out of the welding fume plume.

• Useanair-suppliedrespiratorifventilationisnotadequate

to remove all fumes and gases.

• Thekindsoffumesandgasesfromtheplasmaarcdependon

the kind of metal being used, coatings on the metal, and the

different processes. You must be very careful when cutting

or welding any metals which may contain one or more of the

following:

Antimony Chromium Mercury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• Alwaysread the MaterialSafetyData Sheets(MSDS)that

should be supplied with the material you are using. These

MSDSs will give you the information regarding the kind and

amount of fumes and gases that may be dangerous to your

health.

• Forinformationonhowtotestforfumesandgasesinyour

workplace, refer to item 1 in Subsection 1.03, Publications

in this manual.

• Usespecialequipment,suchaswaterordowndraftcutting

tables, to capture fumes and gases.

• Donotusetheplasmatorchinanareawherecombustible

or explosive gases or materials are located.

• Phosgene,atoxicgas,isgeneratedfromthevaporsofchlo-

rinated solvents and cleansers. Remove all sources of these

vapors.

• Thisproduct,whenusedforweldingorcutting,produces

fumes or gases which contain chemicals known to the State

of California to cause birth defects and, in some cases, cancer.

(CaliforniaHealth&SafetyCodeSec.25249.5etseq.)

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process uses

and produces high voltage electrical energy. This electric energy

can cause severe or fatal shock to the operator or others in the

workplace.

• Nevertouchanypartsthatareelectrically“live”or“hot.”

• Weardry glovesand clothing. Insulateyourselffromthe

work piece or other parts of the welding circuit.

• Repairorreplaceallwornordamagedparts.

• Extracare mustbe takenwhentheworkplaceis moistor

damp.

• InstallandmaintainequipmentaccordingtoNECcode,refer

to item 9 in Subsection 1.03, Publications.

• Disconnectpowersourcebeforeperforminganyserviceor

repairs.

• ReadandfollowalltheinstructionsintheOperatingManual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or the plasma

arc.

• Besurethereisnocombustibleorammablematerialinthe

workplace. Any material that cannot be removed must be

protected.

CUTMASTER 12mm, 20mm, 25mm

GENERAL INFORMATION 1-2 Manual 0-5117

• Ventilateallammableorexplosivevaporsfromthework-

place.

• Donotcutorweldoncontainersthatmayhaveheldcom-

bustibles.

• Provide a re watch when working in an area where re

hazards may exist.

• Hydrogengasmaybeformedandtrappedunderaluminum

work pieces when they are cut underwater or while using a

water table. DO NOT cut aluminum alloys underwater or on

a water table unless the hydrogen gas can be eliminated or

dissipated. Trapped hydrogen gas that is ignited will cause

an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc processes can

cause noise levels to exceed safe limits. You must protect your ears

from loud noise to prevent permanent loss of hearing.

• Toprotectyourhearingfromloudnoise,wearprotectiveear

plugs and/or ear muffs. Protect others in the workplace.

• Noise levels should be measured to be sure the decibels

(sound) do not exceed safe levels.

• Forinformationonhowtotestfornoise,seeitem1inSub-

section 1.03, Publications, in this manual.

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin. The

plasma arc process produces very bright ultra violet and infra red

light. These arc rays will damage your eyes and burn your skin if

you are not properly protected.

• Toprotectyoureyes,alwayswearaweldinghelmetorshield.

Also always wear safety glasses with side shields, goggles

or other protective eye wear.

• Wearweldingglovesandsuitableclothingtoprotectyour

skin from the arc rays and sparks.

• Keephelmetandsafetyglassesingoodcondition.Replace

lenses when cracked, chipped or dirty.

• Protectothersintheworkareafromthearcrays.Useprotec-

tive booths, screens or shields.

• UsetheshadeoflensassuggestedinthefollowingperANSI/

ASC Z49.1:

Minimum Protective Suggested

Arc Current Shade No. Shade No.

Less Than 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* These values apply where the actual arc is clearly

seen. Experience has shown that lighter ﬁlters may

be used when the arc is hidden by the work piece.

LEAD WARNING

This product contains chemicals, including lead, or otherwise

produces chemicals known to the State of California to cause

cancer, birth defects and other reproductive harm. Wash hands

after handling. (CaliforniaHealth&SafetyCode§25249.5etseq.)

1.03 Publications

Refer to the following standards or their latest revisions for more

information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR 1910,

obtainable from the Superintendent of Documents, U.S.

GovernmentPrintingOfce,Washington,D.C.20402

2. ANSI Standard Z49.1, SAFETY IN WELDING AND CUTTING,

obtainable from the American Welding Society, 550 N.W.

LeJeune Rd., Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING AND GAS

WELDING AND CUTTING, obtainable from the Superin-

tendentofDocuments,U.S.GovernmentPrintingOfce,

Washington, D.C. 20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCUPATION

AND EDUCATIONAL EYE AND FACE PROTECTION, obtain-

able from American National Standards Institute, 1430

Broadway, New York, NY 10018

5. ANSI Standard Z41.1, STANDARD FOR MEN’S SAFETY-

TOE FOOTWEAR, obtainable from the American National

Standards Institute, 1430 Broadway, New York, NY 10018

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE OF

CUTTING AND WELDING PROCESSES, obtainable from

American National Standards Institute, 1430 Broadway,

New York, NY 10018

7. AWS Standard A6.0, WELDING AND CUTTING CONTAIN-

ERS WHICH HAVE HELD COMBUSTIBLES, obtainable from

American Welding Society, 550 N.W. LeJeune Rd., Miami,

FL 33126

8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS FOR

WELDING, CUTTING AND ALLIED PROCESSES, obtainable

from the National Fire Protection Association, Batterymarch

Park, Quincy, MA 02269

9. NFPA Standard 70, NATIONAL ELECTRICAL CODE, obtain-

able from the National Fire Protection Association, Battery-

march Park, Quincy, MA 02269

10. NFPA Standard 51B, CUTTING AND WELDING PROCESSES,

obtainable from the National Fire Protection Association,

Batterymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COMPRESSED

GASES IN CYLINDERS, obtainable from the Compressed

Gas Association, 1235 Jefferson Davis Highway, Suite 501,

Arlington, VA 22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELDING

AND CUTTING, obtainable from the Canadian Standards

Association, Standards Sales, 178 Rexdale Boulevard,

Rexdale, Ontario, Canada M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY obtain-

able from the National Welding Supply Association, 1900

Arch Street, Philadelphia, PA 19103

14. American Welding Society Standard AWSF4.1, RECOM-

MENDED SAFE PRACTICES FOR THE PREPARATION FOR

WELDING AND CUTTING OF CONTAINERS AND PIPING

THAT HAVE HELD HAZARDOUS SUBSTANCES, obtainable

from the American Welding Society, 550 N.W. LeJeune Rd,

Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY PRO-

TECTION, obtainable from American National Standards

Institute, 1430 Broadway, New York, NY 10018

CUTMASTER 12mm, 20mm, 25mm

Manual 0-5117 1-3 INFORMATIONS GÉNÉRALES

1.04 Note, Attention et Advertissement

Danscemanuel,lesmots“note,”“attention,”et“avertissement”sont

utilisés pour mettre en relief des informations à caractère important.

Cesmisesenreliefsontclassiéescommesuit:

NOTE

Toute opération, procédure ou renseignement géné-

ral sur lequel il importe d’insister davantage ou qui

contribue à l’efﬁcacité de fonctionnement du système.

ATTENTION

Toute procédure pouvant résulter l’endommagement

du matériel en cas de non-respect de la procédure en

question.

AVERTISSEMENT

Toute procédure pouvant provoquer des blessures de

l’opérateur ou des autres personnes se trouvant dans

la zone de travail en cas de non-respect de la procédure

en question.

AVERTISSEMENT

Fournit l'information concernant des dommages pos-

sibles de choc électrique. Des avertissements seront

enfermés dans une boîte de ce type.

1.05 Precautions De Securite Importantes

AVERTISSEMENTS

L’OPÉRATION ET LA MAINTENANCE DU MATÉRIEL

DE SOUDAGE À L’ARC AU JET DE PLASMA PEUVENT

PRÉSENTER DES RISQUES ET DES DANGERS DE

SANTÉ.

Coupant à l’arc au jet de plasma produit de l’énergie

électrique haute tension et des émissions magnétique

qui peuvent interférer la fonction propre d’un “pacema-

ker” cardiaque, les appareils auditif, ou autre matériel

de santé electronique. Ceux qui travail près d’une

application à l’arc au jet de plasma devrait consulter

leur membre professionel de médication et le manufac-

turier de matériel de santé pour déterminer s’il existe

des risques de santé.

Il faut communiquer aux opérateurs et au personnel

TOUS les dangers possibles. Aﬁn d’éviter les blessures

possibles, lisez, comprenez et suivez tous les avertis-

sements, toutes les précautions de sécurité et toutes

les consignes avant d’utiliser le matériel. Composez

le + 603-298-5711 ou votre distributeur local si vous

avez des questions.

FUMÉE et GAZ

La fumée et les gaz produits par le procédé de jet de plasma peuvent

présenterdesrisquesetdesdangersdesanté.

• Eloigneztoutefuméeetgazdevotrezonederespiration.Gardez

votre tête hors de la plume de fumée provenant du chalumeau.

• Utilisezunappareilrespiratoireàalimentationenairsil’aération

fournie ne permet pas d’éliminer la fumée et les gaz.

• Lessortesdegazetde fumée provenant de l’arcdeplasma

dépendent du genre de métal utilisé, des revêtements se trouvant

sur le métal et des différents procédés. Vous devez prendre soin

lorsquevouscoupezousoudeztoutmétalpouvantcontenirun

ou plusieurs des éléments suivants:

antimoine cadmium mercure

argent chrome nickel

arsenic cobalt plomb

baryum cuivre sélénium

béryllium manganèse vanadium

• Liseztoujoursleschesdedonnéessurlasécuritédesmatiè-

res(sigleaméricain“MSDS”);celles-cidevraientêtrefournies

aveclematérielquevousutilisez.LesMSDScontiennentdes

renseignementsquantàlaquantitéetlanaturedelafuméeet

des gaz pouvant poser des dangers de santé.

• Pourdesinformationssurlamanièredetesterlafuméeetles

gaz de votre lieu de travail, consultez l’article 1 et les documents

cités à la page 5.

• Utilisezunéquipementspécialtelquedestablesdecoupeàdébit

d’eau ou à courant descendant pour capter la fumée et les gaz.

• N’utilisezpaslechalumeauaujetdeplasmadansunezoneoù

se trouvent des matières ou des gaz combustibles ou explosifs.

• Lephosgène,ungaztoxique,estgénéréparlafuméeprovenant

des solvants et des produits de nettoyage chlorés. Eliminez toute

source de telle fumée.

• Ceproduit,dansleprocéderdesoudageetdecoupe,produit

de la fumée ou des gaz pouvant contenir des éléments reconnu

dansL’étatdelaCalifornie,quipeuventcauserdesdéfautsde

naissance et le cancer. (La sécurité de santé en Californie et la

codesécuritéSec.25249.5etseq.)

CHOC ELECTRIQUE

Leschocsélectriquespeuventblesseroumêmetuer.Leprocédéau

jetdeplasmarequiertetproduitdel’énergieélectriquehautetension.

Cetteénergieélectriquepeutproduiredeschocsgraves,voiremor-

tels, pour l’opérateur et les autres personnes sur le lieu de travail.

• Netouchezjamaisunepièce“soustension”ou“vive”;portezdes

gants et des vêtements secs. Isolez-vous de la pièce de travail

ou des autres parties du circuit de soudage.

• Réparezouremplaceztoutepièceuséeouendommagée.

• Prenezdessoinsparticulierslorsquelazonedetravailesthumide

ou moite.

• MontezetmaintenezlematérielconformémentauCodeélectri-

quenationaldesEtats-Unis.(Voirlapage5, article 9.)

• Débranchezl’alimentationélectriqueavanttouttravaild’entretien

ou de réparation.

• LisezetrespecteztouteslesconsignesduManueldeconsignes.

CUTMASTER 12mm, 20mm, 25mm

INFORMATIONS GÉNÉRALES 1-4 Manual 0-5117

INCENDIE ET EXPLOSION

Les incendies et les explosions peuvent résulter des scories chaudes,

des étincelles ou de l’arc de plasma. Le procédé à l’arc de plasma

produit du métal, des étincelles, des scories chaudes pouvant mettre

lefeuauxmatièrescombustiblesouprovoquerl’explosiondefumées

inammables.

• Soyezcertainqu’aucunematièrecombustibleouinammablene

setrouvesurlelieudetravail.Protégeztoutetellematièrequ’il

est impossible de retirer de la zone de travail.

• Procurezunebonneaérationdetouteslesfuméesinammables

ou explosives.

• Necoupezpasetnesoudezpaslesconteneursayantpurenfer-

mer des matières combustibles.

• Prévoyezuneveilled’incendielorsdetouttravaildansunezone

présentant des dangers d’incendie.

• Legashydrogènepeutseformerous’accumulersouslespièces

detravailenaluminiumlorsqu’ellessontcoupéessousl’eauou

sur une table d’eau. NE PAS couper les alliages en aluminium

sousl’eauousurunetabled’eauàmoinsquelegashydrogène

peut s’échapper ou se dissiper. Le gas hydrogène accumulé

exploserasienammé.

RAYONS D’ARC DE PLASMA

Les rayons provenant de l’arc de plasma peuvent blesser vos yeux et

brûler votre peau. Le procédé à l’arc de plasma produit une lumière

infra-rouge et des rayons ultra-violets très forts. Ces rayons d’arc

nuiront à vos yeux et brûleront votre peau si vous ne vous protégez

pas correctement.

• Pourprotégervosyeux,porteztoujoursuncasqueouunécran

de soudeur. Portez toujours des lunettes de sécurité munies de

parois latérales ou des lunettes de protection ou une autre sorte

de protection oculaire.

• Portezdesgantsdesoudeuretunvêtementprotecteurapproprié

pour protéger votre peau contre les étincelles et les rayons de

l’arc.

• Maintenezvotrecasqueetvoslunettesdeprotectionenbonétat.

Remplaceztoutelentillesaleoucomportantssureourognure.

• Protégezlesautrespersonnessetrouvantsurlazonedetravail

contre les rayons de l’arc en fournissant des cabines ou des

écrans de protection.

• Utilisezlanuancedelentillequiestsuggèréedanslerecommen-

dationquisuiventANSI/ASCZ49.1:

Nuance Minimum Nuance Suggerée

Courant Arc Protective Numéro Numéro

Moins de 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* Ces valeurs s’appliquent ou l’arc actuel est observé

clairement. L’experience a démontrer que les ﬁltres

moins foncés peuvent être utilisés quand l’arc est caché

par moiceau de travail.

BRUIT

Lebruitpeutprovoquerunepertepermanentedel’ouïe.Lespro-

cédésdesoudageàl’arcdeplasmapeuventprovoquerdesniveaux

sonores supérieurs aux limites normalement acceptables. Vous

dúezvousprotégerlesoreillescontrelesbruitsfortsand’éviter

unepertepermanentedel’ouïe.

• Pourprotégervotreouïecontrelesbruitsforts,portezdestam-

pons protecteurs et/ou des protections auriculaires. Protégez

également les autres personnes se trouvant sur le lieu de travail.

• Ilfautmesurerlesniveauxsonoresand’assurerquelesdécibels

(le bruit) ne dépassent pas les niveaux sûrs.

• Pour des renseignements sur la manière de tester le bruit,

consultez l’article 1, page 5.

PLOMB AVERTISSEMENT

Ce produit contient des produits chimiques, comme le plomb,

ou engendre des produits chimiques, reconnus par l’état de

Californie comme pouvant être à l’origine de cancer, de mal-

formations fœtales ou d’autres problèmes de reproduction.

Il faut se laver les mains après toute manipulation.

(Code de Californie de la sécurité et santé, paragraphe 25249.5 et

suivants)

Otros manuales para CUTMASTER

Tabla de contenidos

Otros manuales de Sistema de soldadura de Thermal Dynamics

Thermal Dynamics

Thermal Dynamics CutMaster 75 Manual de usuario

Thermal Dynamics

Thermal Dynamics 1-4730-6 Manual de usuario

Thermal Dynamics

Thermal Dynamics A40 Manual de usuario

Thermal Dynamics

Thermal Dynamics CE CutMaster 80XL Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTMASTER 12 Manual de usuario

Thermal Dynamics

Thermal Dynamics CutMaster 58 Manual de usuario

Thermal Dynamics

Thermal Dynamics CE CutMaster 80XL Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTSKILL C-35C Manual de usuario

Thermal Dynamics

Thermal Dynamics PAK 200 Manual de usuario

Thermal Dynamics

Thermal Dynamics PAK Master 150XL Manual de usuario

Thermal Dynamics

Thermal Dynamics SL60 Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTMASTER 39 Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTMASTER A-09207 Manual de usuario

Thermal Dynamics

Thermal Dynamics Econo-Pak 50 Manual de usuario

Thermal Dynamics

Thermal Dynamics Ultra-Cut 400 Manual de usuario

Thermal Dynamics

Thermal Dynamics MERLIN 6000 Manual de usuario

Thermal Dynamics

Thermal Dynamics A40 Manual de usuario

Thermal Dynamics

Thermal Dynamics PCH-100XL Manual de usuario

Thermal Dynamics

Thermal Dynamics Pak Master 25 Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTMASTER SL100SV Manual de usuario

Thermal Dynamics

Thermal Dynamics C-70A CUTSKILL Manual de usuario

Thermal Dynamics

Thermal Dynamics CUTMASTER 60i Manual de usuario

Thermal Dynamics

Thermal Dynamics 38 Cutmaster Manual de usuario

Thermal Dynamics

Thermal Dynamics AUTO-CUT 300 XT Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario