Therma-Ray SmartRooms Manual de usuario

Whether you're a contractor, architect, builder or homeowner, 

creating the perfect indoor environment has always been a challenge.

Therma·Ray, the world's #1name in thermal comfort systems introduces

you to the ultimate solution, SmartRooms. Please take the time to read

this installation guide carefully before you begin. Remember, accurate

measurements are the key to success for a proper installation.

Standard Package Includes:

1) SmartRooms Controller

2) 6 screws (2 painted white)

3) Box ring

4) 240/120 volt power module with built in Ground Fault Circuit

Interrupter (GFCI)

5) Extended double gang electrical box (Canada only)

NOT INCLUDED

4 - Wire Nuts

COMFORT CONTROLLER

Line Voltage Installation Guide

FOR USE ON:

· Heating only 240/120 Double Pole Applications with Power

Module.

· All Therma-Ray Radiant Heating products that will be connected to

120 or 240 volt power source.

ELECTRIC RATING:

· 16A at 240/120 Vac

· 3840W at 240 Vac (Non-Inductive)

· 1920W at 120 Vac (Non-Inductive)

TEMPERATURE DIFFERENTIAL

· Adjustable Range

SENSORS: By the time you are ready to connect your controller, the sensors

(if applicable) should already have been installed. Review the installation

instructions for your particular Therma-Ray Radiant Heating System for more

information regarding the sensors.

INSTALLATION

WARNING

· This controller when used with the power module is a line

voltage (240/120) control. Do not install it unless you are

completely familiar with house wiring. If improperly

handled, there can be a risk of electric shock hazard which

may cause serious injury or death.

· The SmartRooms Comfort Controller is rated for normal full

load current on a dual residential 20A circuit breaker or fuse

block. Do not use on circuits protected by higher-rated

over-current protection devices. Some sustained fault

conditions can cause product failure.

·Do NOT connect to voltage different from device rating.

CAUTION

· Disconnect power supply before making wire connections to

prevent electrical shock or equipment damage.

· All wiring must comply with applicable codes and

ordinances.

· Maximum load for this thermostat MUST NOT EXCEED

specified rating otherwise potential fire hazard exists.

NOTE: The power module has it's own built in Ground Fault Circuit

Interrupter (GFCI). Therefore do not install a GFCI breaker on the

circuit as this will cause the Controller to trip therefore preventing

your heating system from operating.

Diagram 1

Green WIre Copper WIre

Picture 1 - Floor warming version

Picture 2 -

Floor warming version

Blue Black

White Blue

Picture 3.

Black Power

Feed

Black Module

Wire

Red Power

Feed

Red Module

Wire

Picture 4

Page 2

Steel Braid ( Floor

Warming Only)

CAUTION: MAKE SURE ALL POWER IS OFF.

The power module has 2 blue wires that will be connected to the load. (In a floor

warming installation the load is the two floor warming lead wires). The small green

wire is a ground wire and will be connected to a screw in the electrical box. The red

and black wires will be connected to the two power (line) voltage wires (usually red

and black in colour).

Check the voltage switch to ensure it is in the right position (120 volt or 240

volt) based on the voltage it is connected to. The controller is factory-set to

240V. To set the controller for 120V move the switch to the 120V position.

Connecting the controller to a higher voltage will void the warranty.

Step 1 -Strip all the wires as needed to expose enough bare wire to make good

connections.

Step 2 - Take the green wire from the power module, (if applicable the 2 steel braids

from the floor warming lead wires), and the copper wire from the power feed cable

and connect them to one or more of the screws in the electrical box. It is not

necessary to connect all of these wires to the same screw. As long as all the wires are

connected to a screw in the box, the system will be grounded. (See picture 1)

Floor Warming

Step 3 - Take one blue wire from the power module and connect it to the white lead

wire from the floor warming system using a wire nut. Make sure the two (2) wires are

securely connected. (Do not use electrical tape in replace of wire nuts). (See picure 2)

Step 4 - Same as Step 3 except connect the other blue wire to the black floor warming

lead wire. (See picture 2)

Step 5 - Take the black wire from the power module and connect it to the black 240

or 120 volt power conductor. Use a wire nut to connect the two (2) wires. (See

picture 3)

Step 6 - Same as Step 4 except connect the red power module wire to the last

remaining power conductor. (See picture 4)

All wires should now be connected. All the ground wires should be attached to a

ground screw.

Ceiling or ETS Installation

Step 3 - Take one blue wire from the power module and connect it to the red load

ceiling wire using a wire nut. Make sure the two (2) wires are securely connected. (Do

not use electrical tape in replace of wire nuts) (See picture 2)

Step 4 - Same as step 3 except connect the other blue wire to the black load ceiling

wire.

Step 5 - Take the black wire from the power module and connect it to the black line

power conductor. Use a wire nut to connect the two (2) wires . (See picture 3)

Step 6 - Same as Step 5 except connect the red power module wire to the last

remaining conductor. (See picture 4)

All wires should now be connected.

Low Voltage

Panel (RJ45)

Connection

Floor Sensor

(if applicable)

High Limit

Sensor

240/120 Volt

Module Connection

Back view of Face Plate

Step 7 - Slide the box ring into place and secure it to the electrical box

using the 4 screws supplied.

Step 8 - The power module simply snaps into the back of the controller

face place with the 5 pin black connector.

Step 9 - Insert the sensor (s) (if applicable) in the back of the SmartRooms

Controller. (See Diagram 2 as to the correct sensor connection).

Step 10 - Attach the controller to the box ring using the 2 painted screws

provided. The controller should be flush to the wall.

Step 11 - Turn on the power at your service entrance panel.

WARNING:

To avoid risk or fire hazard, all connections to aluminum conductors

must be made using approved CO/ALR solderless wire connectors.

WARRANTY

Therma-Ray Inc. One (1) Year LImited Warranty

Therma-Ray Inc. warrants the controller is free of defects in material and

workmanship after proper installation for a one (1) year period from the date

of installation. During this period, Therma-Ray Inc. will replace or repair the

controller without charge if it has been used under normal conditions. This

warranty does not cover delivery costs. The warranty does not apply if poorly

installed or damaged after installation. Therma-Ray Inc. will not compensate

for consequential damage, direct or indirect resulting from the failure of the

controller. All other representations, warranties and conditions, whether oral or

written, express or implied, statuatory or otherwise are expressly excluded. The

defective controller must be returned to the place of purchase or sent prepaid

to Therma-Ray Inc.

Therma-Ray Inc.

670 Wilsey Road, Fredericton, N.B.

Canada E3B 7K4

Tel: 506-457-4600 .

Fax: 506-457-4699

E-mail: sales@thermaray.com

www.thermaray.com

Printed in Canada

Revised March 2008



Diagram 2

(See Diagram 1 on the front page).

Page 3

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario