THE WORLD MODELS Wing Jet EP Manual de usuario

Wing Span

Wing Area

Flying Weight

Fuselage Length

39.5 in / 1000 mm

301 sq in / 19.4 sq dm

22 oz / 620 g

17.5 in / 440 mm

Requires : 3-channel “mixing” radio (elevator & ailerons),

2 micro servos, Ducted Fan Propulsion Unit

PL6800010 and Outrunner Motor KM0283110,

30A(burst 35A) brushless ESC, 3 cells 11.1V 15C

2100 mAh Li - Po battery & charger.

Specifications

*Specifications are subject to change without notice.*

INSTRUCTION MANUAL

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY(ARF)SERIES

MADE IN CHINA

Warning ! This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind

of electric powered precision model. Operating this model without prior preparation may cause

injuries. Remember, safety is the most important thing. Always keep this instruction manual at

hand for quick reference.

Wing Jet EP

The World Models

Manufacturing Co., Ltd.

www.theworldmodels.com

E210NXMPO24831008

INDEX

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

P.1

P.2

P.3-P.8

P.8

Check all parts. If you find any defective or missing parts contact your local dealer. Please

DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.

Any parts you find to be defective after the gluing process may be difficult to remove for

warranty replacement. The manufacturer will replace any defective parts, but will not extend

to the parts that are good before gluing to defective parts during assembly. Warranty will

not cover any parts modified by customer.

Symbols used throughout this instruction manual comprise of the following :-

Read through the manual before you begin, so you will have an overall idea of what to do.

Cut off shaded portion.

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(C.A.glue, super glue.)

Assemble left and right

sides the same way.

Peel off shaded portion

covering film.

Pay close attention here!

Apply epoxy glue.

Must be purchased separately !

Drill holes with the specified

diameter (here: 3mm). Pierce the shaded portion

covering film.

3mm

Do not overlook this symbol !

Warning!

Apply thread locker

P.1

Wing Jet EP

E210NXMPO24831008

Parts List

P.2

COVERING:--

LIGHTEX SGX210000

LIGHTEX SGX100

1. MAIN WING -- 1 pair

2. SCREW PB2x10mm -- 4 pcs

SCREW PA1.7x8mm -- 8 pcs

STRAPER PL4112106 -- 2 pcs

CLEVIS PL4112105 -- 2 pcs

FUEL TUBE d2xD4x4mm -- 4 pcs

HORN PL4113102 -- 2 sets

PUSHROD Ø1.4x97mm w/ Threads (For Aileron) -- 2 pcs

MICRO AILERON SERVO MOUNT PL5310020 -- 1 pair

3. WING JOINER Ø5x135mm -- 1 pc.

4. VERTICALFIN -- 1 set

SCREW PM2x20mm -- 2 pcs

WASHER d2xD5mm -- 4 pcs

M2 NYLON INSERT LOCK NUT-- 2 pcs

5. BATTERYTIE 200mm -- 1 pc.

SPONGE 10x50x150mm -- 2 pcs

DOUBLE-SIDED TAPE 30x35mm -- 1 pc.

CABLETIE (For Brushless ESC) 1x2.5x200mm -- 1 pc.

6. SCREW PWM3x13mm -- 4 pcs

M3 NUT -- 4 pcs

7. SCREW PM2.5x20mm -- 2 pcs

WASHER d2.5xD8mm -- 2 pcs

DOUBLE-SIDED TAPE 30x35mm -- 1 pc.

PLYWOOD 2x20x40mm (Wing Protection) -- 1 pc.

8. CANOPY -- 1 pc.

9. FIELD STAND/ LAUNCHING PAD -- 1 set

DECALS -- 1 set

E210NXMPO24831008

Aileron Servo Lead

Main Wing

Apply instant type CA glue

to both sides of each hinge.

Aileron Servo

PB2x10mmScrew

Ø1mm pilot holes for World

Models tri-horn are pre-drilled.

Please look for pin-hole marks

at under side of control surfaces.

PA1.7x8mm Screw

Please choose either 02L & 02R or 03L & 03R or 04L & 04R

that suits your servo.

02L

03L

04L

02R

03R

04R

Fuel Tube

d2xD4x4mm

Clevis

Horn

PB2x10mm Pushrod

Ø1.4x97mm

Straper

Fuel Tube

d2xD4x4mm

PA1.7x8mm

P.3

TWM PL8210010

CLEVIS WRENCH

Bottom View

E210NXMPO24831008

Front

Battery Battery Tie

30ABrushlessESC Double-Sidedtape

P.4

Battery & ESC

Vertical Fin

Install and arrange the equipment as shown in

the picture.

Main Wing

Please apply glue to wing joiner and all surfaces in contact.

Ø5x135mm

d2xD5mmWasher

d2xD5mm

Washer

PM2x20mmScrew

PM2x20mm

M2NylonInsertLockNut

M2NylonInsert

LockNut

Completed

Bottom View

30ABrushless

ESC

Cable Tie

E210NXMPO24831008

Ducted Fan Propulsion Unit with 28/31 Motor

1 2 3

4 5 6

Make sure TWM logo on ducted

fan stays on top of fuselage.

PWM3x13mmScrew

PWM3x13mm

PM2x5mmScrew

PM2x5mm

M3x6mm

CenterLine

M3x6mmSocketHeadScrew

M3NUT

Completed

Rear View

TWM

P.5

Make sure rotating motor casing

is not in contact with wirings or

anything.

OutrunnerMotor28/31

KM0283110

DuctedFanPropulsionUnitPL6800010

Optional Parts

Solder Solder

TWM

KP0011310

ESC Ducted Fan

E210NXMPO24831008

Receiver

PM2.5x20mmScrew

AntennaLead

Double-SidedTape

d2.5xD8mm

Washer

Canopy

PM2.5x20mm

Plywood

2x20x40mm

d2.5xD8mm

Washer

Completed

P.6

E210NXMPO24831008

Field Stand/ Launching Pad

Completed

The field stand can be used as a launching-pad if you are flying on paved

runways. Place the Wing Jet on the stand, point it into the wind, check your

controls and advance the throttle. When the Wing Jet gets enough air speed,

pull the elevator gently and the Wing Jet will fly off the field stand and get

airborne gracefully.

If you are flying on grass fields and could not use the field stand as a

launching pad, you will need to hand launch the Wing Jet.

When the Wing Jet has gained enough air speed, gently pull the elevator

and let the Wing Jet climb to a higher safe altitude. Reduce the throttle to

slow the Wing Jet while maintaining altitude. The Wing Jet should fly well

about half throttle. You may add power when turning, climbing or doing

loops. Learn how the Wing Jet behaves and adjust the trims for level flight.

To avoid overheating of ducted fan motor and battery, we recommend you

use full power intermittently. This will also give you longer flying time and

extend the battery life.

For the first hand launch flight, we recommend having an assistant to hand

launch the Wing Jet for you. Ask your assistant to hold the Wing Jet by the

fuselage, pointed into the wind, while you check the correct control surface

response. Fully advance the throttle to start the motor and once the ducted

fan is at full power, the hand launcher should gently push the plane into the

air at a level attitude. Don’t use excessive force as it is not necessary, and

don’t throw the model up the sky as it will cause the model to stall before

gaining air speed. Make sure the Wing Jet is being launched into the wind

and be alert to make corrections to keep the model flying straight and level

into the wind.

P.7

E210NXMPO24831008

Control Throws

C.G.

6mm

Aileron/ Elevator

The ideal C.G. position is 70mm (2.75in)

behind the leading edge measured at where

the wing meets the fuselage. In order to

obtain the C.G. specified, add weight to the

fuselage or move the battery position.

Check the C.G. before flying.

70mm

2.75in

C.G.

Warning!

Important Safety Precautions

Wing Jet EP

Adjust the control throws as shown in the diagram.

These throws are good for general flying. You can

adjust according to your personal preference.

Please note that the mixing function of your radio will add up the control throws of

aileron and elevator input. A control throw of 6mm for the aileron or elevator alone

will give you up to 12mm throw if you input aileron and elevator throw at the same time.

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.

# is specially designed to be powered by KM0283110 Outrunner Motor.

# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running

propeller. Extreme caution should be exercised when working with electric powered models. Make sure the

propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure

you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you

plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental

movement of the throttle stick will spin the propeller and could cause injuries.

# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.

Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.

Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the

glue and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

P.8

E210NXMPO24831008

Product Registration Form (US Customers)

We would like to share with you any relevant information regarding your model, including

product news and free upgrade parts when applicable. Please fill in the following and send to

AirBorne Models, 4749-K, Bennett Drive, Livermore, CA94551 USA.

1. Name:______________________________________________

2.Address:____________________________________________

3. Phone #:____________________ E-mail:__________________

4. Model:______________________________________________

Wing QC#__________ Fuselage QC# _______________________

(QC numbers are stamped on wing and fuselage)

5. Date of Purchase:_____________________________________

6. Store Name: _________________________________________

Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.

Thank you very much for purchasing our product.

E210NXMPO24831008

Tabla de contenidos

Otros manuales de Juguete de THE WORLD MODELS

THE WORLD MODELS

THE WORLD MODELS CAP 232-46S Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Velox REV II-60 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS RAMBLER-45 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Pilatus PC-6 Porter 40 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Delta Jet EP Manual de usuario

THE WORLD MODELS

THE WORLD MODELS ZERO FIGHTER 40 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS A340 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Katana EP Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Spot-On 50 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS 1/3 PAULISTINHA P-56 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS ARF Zen 30 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS F4U CORSAIR EP Manual de usuario

THE WORLD MODELS

THE WORLD MODELS PIPER J-3 CUB 26s Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Nemesis 52 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Zero Fighter 60S Manual de usuario

THE WORLD MODELS

THE WORLD MODELS 1/4 SUPER CUB Manual de usuario

THE WORLD MODELS

THE WORLD MODELS P-51 MUSTANG 46 Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Jeff Troy's TAMEcat Trainer 40 ARF Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Velox REV II Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Clipped Wing Cub EP Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Outregeous Manual de usuario

THE WORLD MODELS

THE WORLD MODELS 50CC Paulistinha Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Extra 300 EP Manual de usuario

THE WORLD MODELS

THE WORLD MODELS Jeff Troy's TAMEcat DF Trainer Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario