THE SHOWER LAB VIEW 23 Manual de usuario

05/2021 V 1.0

VIEW 23 Illustration - View 23

H1 Handle

SB8 Stay Bar

Right Hand

05/2021 V 1.0

IMPORTANT

•This shower screen / enclosure must be installed by suitably qualified individuals. We

recommend a minimum of two people for safe assembly of certain sections of this screen.

•Ensure all appropriate safety equipment, especially protective footwear, safety glasses

and gloves are used.

•When drilling holes in ceramic tiles, use masking tape to prevent the drill from slipping:

DO NOT use hammer action as this will crack the tiles. Use a high quality drill bit to ensure

a clean, precise hole.

Tighten hinges and brackets to the recommended 15.6N.

•

Please leave these instructions with the customer following installation.

PRIOR TO INSTALLATION

•Before disposing of the packaging and prior to commencing assembly, please check all

the components to ensure that they have been supplied correctly and are undamaged.

Subsequent claims for missing or damaged pieces will not be accepted once the

packaging has been disposed of and installation commenced.

•In the event of any queries please contact your supplier quoting the relevant model

information.

•The Tray / Tiled floor on which this screen is to be installed must be level on all sides.

•It may be necessary to use alternate fixings to those supplied, depending on the properties

of the walls to be fixed to.

•Use the protective corners supplied at all times until the glass is moved to its final position.

•Ensure that the glass is installed correctly, taking care to avoid installing the glass upside

down. On certain panels an easy clean coating is applied to one side only, this is clearly

marked with a sticker on the non-coated side. The coated surface is to be fitted inwards

towards the inside (wet side) of the screen.

•Ensure that all surfaces to be sealed are clean and dry prior to applying the silicone

sealant. Use a high grade fungal resistant sealant.

•Allow a minimum of 24 hours after application of the silicone sealant prior to using the

screen.

TOOLS & MATERIALS REQUIRED

Junior Hacksaw

Straight Edge (Steel

Rule)

Fine Tooth File

Set or Roofing

Square

Masking Tape

Modelling Knife

Spirit Level

Pencil

Silicone Gun

Power Drill

Ø6mm Masonry Drill Bit

2x Suction Glass Lifters

High Quality Silicone Sealant

Tape Measure

Pozi-drive

Screwdrivers, PZ1&2

Safety Glasses and

Gloves

CARE AND MAINTENANCE

(please ensure that these instructions are left with the installed unit)

•We recommend routine cleaning of your screen / enclosure with hot water using a soft

cloth, then drying with a dry soft cloth or chamois leather.

Ritec Aftercare for Shower Glass is recomended for best results.

•All glass has been treated with EASY CLEAN glass finish and care must be taken to avoid

any abrasive cleaning products that may damage the special surface protection.

•DO NOT use acidic based de-scaler products or products containing bleaches or solvents.

Digital Torque Wrench

05/2021 V 1.0

Supplied Parts

Inline xed panel

Door

Nylon Block

Glass Support

Return panel

Glass to Glass Hinge

Wall Prole End Cap

Door Handle

(Option dependant)

Inline xed panel

05/2021 V 1.0

Supplied Parts

Underframe Wedge Gasket

Underframe

Underframe Gasket

Wall Prole

Wall Prole Soft Seal

Wall Prole Rigid Seal

Underframe Top

Glass to Glass Bubble “h” Seal

Glass to Glass Seal

05/2021 V 1.0

Supplied Parts

Bottom Door Seal

Spacers

Underframe 90°Connector

Packers

Glass to Glass Adhesive Gasket

05/2021 V 1.0

Supplied Parts

Please use this page to nd which stay bar your enclosure has been supplied with.

SB8 - With Glass Clamp

and T Connectors

05/2021 V 1.0

These instructions are for the View 23. An SB8 Stay Bar is used for this illustration.

The following instructions are valid for both the 20mm and 30mm proles. The 30mm prole is

used in the following instructions.

Please use the below diagram to reference the list of parts.

Return Panel

Door Panel

Fixed Inline Panel (Handle Side)

Wall Prole

Wall Prole End Cap

Wall Prole Soft Seal

Wall Prole Rigid Seal

Underframe Wedge Gasket

JUnderframe

Fixed Inline Panel (Hinge Side)

Underframe Gasket

Bottom Door Seal

Underframe Top

Underframe 90°Connector

OGlass to Glass Hinge

PGlass to Glass Seal

QGlass to Glass Bubble Seal

RGlass to Glass Adhesive Gasket

SHandle (If Supplied)

TStay Bar (SB2 Shown)

05/2021 V 1.0

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

ADJUSTMENT SHEET

STANDARD ENCLOSURES

Please Note

Only Standard Enclosures are shown above. If you have a Bespoke Enclosure, reference the delivery

note for the panel speciﬁcaons of the Enclosure.

BESPOKE ENCLOSURES

LH RH

05/2021 V 1.0

Return UF = R - 22mm

Inline UF = F - 44mm

01/17

Posion the Underframe parallel to

tray edge. If using a raised shower tray,

leave a minimum 3mm gap from the

edge of the tray (5mm is

recommended).

Use tape to mark this dimension.

Repeat for the Return Underframe

Proﬁle.

Measure the distance from the tape

edge to the ling and take note of this

distance.

Repeat for the Return Underframe.

F = R =

Check the dimensions are within the

allowed adjustments by referencing the

aached adjustment sheet.

Subtract 44mm from the Front

Underframe dimension and 22mm

from Return Underframe dimension.

This is the proﬁle width. Mark this

measurement on the Underframe.

Cut squarely using a chop saw. Use a

ﬁne toothed ﬁle to remove any burrs,

be careful not to damage the surface

ﬁnish.

3mm minimum

Shower Tray

01 02

03 04

05/2021 V 1.0

02/17

Connect the Underframe Proﬁles

together using the Underframe 90°

Connector and supplied screws.

Remove the backing strips from the self

adhesive and ﬁx ﬁrmly to the tray.

Place the Underframe Gaskets where

the glass will sit into the Underframe

and bu up against the wall.

Place the Wall Proﬁles over the

Underframe and up against the wall.

Ensure the Wall Proﬁles are vercal by

using a spirit level. Mark the posions

of the pre-drilled holes.

05 06

07 08

Tabla de contenidos

Otros manuales de Accesorio de baño de THE SHOWER LAB

THE SHOWER LAB

THE SHOWER LAB VIEW 20 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 31DW Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 03 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 19.3H Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 22 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 31DP Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 11 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 25 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 31DW Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 30 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 19.3H Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 03 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 19F Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 02 VR02S59 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VR01S20 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 02 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB PORTRAIT SLIDER Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 30 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 06 Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 19H Manual de usuario

THE SHOWER LAB

THE SHOWER LAB VIEW 19.3F Manual de usuario

Manuales populares de Accesorio de baño de otras marcas

DURAVIT

DURAVIT C.1 C15240 0090 Manual

Heatstore

Heatstore HSTRL500WTN Manual de usuario

Sunshower

Sunshower PURE SOLO Manual de usuario

Delabie

Delabie Delabie Sporting 714700 Manual de usuario

Kohler

Kohler K-13056 Instrucciones de montaje

ESS

ESS Container TCL-11 Manual de usuario

Mustee

Mustee 22C Manual de usuario

VITRA

VITRA V-Flow Manual de usuario

baliv

baliv DUK-80.30 T Manual de usuario

Malmet

Malmet B105BT Manual de usuario

bathstore

bathstore Transition H1690MM Guía

BELLOSTA

BELLOSTA Edward 0800/M Manual de usuario

baliv

baliv DU-5160 Manual de usuario

Franke

Franke PRTR0006 Manual de usuario

Gessi

Gessi RILIEVO 59011 Manual de usuario

noken

noken VITAE 100188525-N299998810 Manual de usuario

Allen + Roth

Allen + Roth 1142VA-30-201 Manual de usuario

Britex

Britex HBDA Manual de usuario