Texecom Premier Elite 32XPH-W Manual de usuario

Installation Manual

Premier Elite 32XPH-W

INS732

Premier Elite 32XPH-W Installation Instructions

2 INS732

1. Contents

1. Contents...............................................2

2. Premier Elite 32XPH-W ........................3

System Requirements.................................... 3

System Design Considerations ..................... 4

Multiple Expander Systems.............................. 4

Learning Devices ............................................. 4

Placing Devices ............................................... 4

3. Quick Start Guide ................................ 4

4. System Overview .................................5

Mounting the Expander.................................. 6

Wiring ............................................................. 6

Selecting an Address..................................... 6

Ricochet Expander Addressing..................... 7

Introduction ..................................................... 7

Example: Totally wireless system(s)................. 7

5. Programming .......................................7

Premier Elite™ V2.10> 12/24/48/88/168

Ricochet Learn Menu..................................... 7

Auto Zone Type & Area.................................. 8

Deleting Devices ............................................ 9

Summary of Keys used.................................. 9

Premier EliteV2.00 - V2.09 24/48/88/168 & 640

+ Ricochet V2.xx............................................ 9

Introduction ..................................................... 9

Deleting Devices............................................ 10

Device Modes of Operation............................ 10

Zone Types & Attributes................................. 11

Standalone Mode......................................... 12

Standalone Operation.................................. 12

This table shows two example systems...... 13

6. Ricochet Diagnostics ......................... 13

Premier Elite V2.XX ...................................... 13

Devices.......................................................... 13

Interpreting Keypad Displays ......................... 13

Ricochet Diagnostics Menu ........................... 15

Premier Elite V3.XX ...................................... 16

Low signal security ........................................ 16

7. Modes of Operation ........................... 16

Commission Mode....................................... 16

Expander....................................................... 16

Device Commission Mode ............................. 16

8. System Attributes .............................. 17

Polling .......................................................... 17

System Devices............................................ 17

Auto Mode..................................................... 17

Always Awake................................................ 17

Device Specific .............................................. 17

Hybrid Mode (V2.xx) ...................................... 17

Premier Elite 32XPH-W Power Loss ............ 18

9. Specifications .................................... 18

Electrical........................................................ 18

Physical..........................................................18

Standards & Directives ...................................18

Standards ......................................................18

FCC ID: MYJLAIA5000....................................18

FCC warning statement:.................................18

Warranty.........................................................19

Premier Elite 32XPH-W Installation Instructions

INS732 3

2. Premier Elite 32XPH-W

Texecom has developed a new method of wireless security signalling based on the concept of mesh

networking. Mesh-networking is the process whereby every single wireless device is capable of receiving and

retransmitting any signal from any other wireless device on the network. The size, scalability and range of the

entire system are extended as wireless signalling is no longer limited by point-to point communications. The

range of a Ricochet®enabled wireless system is greater than previous systems, with multiple devices capable

of relaying messages to and from even the most remote locations in a building. Each Ricochet enabled

device provides signalling routes to and from control panels. If the wireless communication between devices

weakens, the Ricochet network ‘self-heals’ and automatically re-routes communications via alternate Ricochet

enabled devices. The reliability of the wireless system increases as more Ricochet devices are installed.

SignalSecurity™ further enhances network reliability with each device already aware of the number of

communication paths available to it.

Firmware versions prior to those listed are NOT compatible.

Control Panel

Premier Elite 32XPH-W

Legacy

Ricochet

Ricochet V2.xx

** V2.10 > Premier Elite

12/24/48/88/168 & 640*

See Section 3

N/A

V2.10>

Multiple Expander Support

It is now possible to add multiple expanders to the system allowing for greater flexibility in system design, and

also taking wireless capability to new levels.

Control Panel Capacity

The table below details the maximum number of expanders and devices that may be used on the different

control panels.

Panel

32XPH-W

Expanders

Devices

Premier Elite 12-W & Live™

N/A

Premier Elite 24™

Premier Elite 48™

Premier Elite 48-W™

N/A

Premier Elite 88™

Premier Elite 168™

128

Premier Elite 640™

512

Premier Elite 32XPH-W take 4 address slots on the network.

System Requirements

To enable all of the advanced functionality and diagnostics capability Ricochet the following are minimum

requirements:-

Wintex™ Version 6 Build 16 or later

Ricochet Monitor™ 0.2.15.00 or later

Premier Elite™ Series V2.xx or later

Premier Elite™ 32XPH-W Expanders V2.xx or later

Expander firmware version can be found on the round green sticker located on the RH side of the PCB.

Premier Elite 32XPH-W Installation Instructions

4 INS732

System Design Considerations

To ensure correct setup and operation of the Wireless Network it is important that the following procedures

are used when learning and placing devices.

Multiple Expander Systems

When using multiple expanders great care should be taken when designing the system. Each expander

should be treated as its own wireless network; it is not possible for devices to hop from one wireless network

to the other, it is also not possible for expanders to pass wireless signals from devices not assigned to them

and nor can the expanders talk to each other.

Learning Devices

All devices should be learnt before they are placed in their final location. The expander should be in

commission mode, please see page 16.This will ensure that they are registered on the receiver or control

panel, and that Mesh Networks and routing are established correctly. Please refer to the relevant section in

this document to Learn Devices to the system.

Devices should be at least 1Mtr away but ideally 10m from the receiver when being learned.

Placing Devices

Once all of the devices have been learnt, they will need placing in their desired location, this should be done

by installing devices closest to the expander first and then working outwards so that the last devices installed

are those furthest away from the expander.

Make sure to install devices with the expander in Commission mode. See page 16.

Devices also have a commission mode which will indicate a secure and valid path of communication to the

receiver. See page 16.

You should wait at least 20 minutes after installing the last device to make sure routing has been correctly

established between all system devices.

For maximum reliability and system integrity avoid long and thin set-ups. Do not mount devices on or near metal.

Keep devices away from mains electricity supplies.

Devices are capable of hopping through up to two other devices, or a maximum of three hops.

3. Quick Start Guide

1. Connect Receiver to Control Panel Network & Leave Tamper Circuit Open. See Page 6

2. Ensure all Option Switches are off. See Page 5

3. Learn Devices to Control Panel. See Page 7 Onwards

4. set attributes. See Page 7 Onwards

5. Change Device Attributes according to application. See page 10

6. Place Devices in desired location, use LED to indicate Signal Security. See Page 4 & 16

7. Wait 20 Minutes for Mesh Network to establish

8. Walk Test System.

Premier Elite 32XPH-W Installation Instructions

INS732 5

4. System Overview

1 2 3 4 5 6 7 8

2 4

TX RX

NETWORK

ADDRESS

4 5 4 2 5 6 3 9 12581

TAMPER

DISABLE

1: Function Switch

Used to Learn devices in Standalone mode, and

to clear latched outputs.

2: Network Connection

The + and –terminals provide power whilst the T

and R terminals are transmit and receive data.

3: Outputs 1-8

Eight transistor outputs which can indicate the

status of nodes 1-16. See page 12 for details.

4: Comm. Port Connection

Serial communications port for connecting the

32XPH-W to a PC via PC Com/USB Com or Com

IP/WiFi for use with Ricochet Monitor Software.

5: Lid Tamper

When open puts the system into commission

mode and digitally attenuates the receiver signal

by 15Db.

6: Programming LED’s

Allows programming of devices directly to the

receiver, in conjunction with the learn switch

(Standalone mode only).

7: Tamper Disable

Disables the lid and rear tamper

8: RF LED

Flashes when transmitting or receiving RF data

9: Antenna

RF Antenna

10: Network LED’s

Green LED = Data received by the expander

from the panel Red LED = Data transmitted by

the expander to the panel. (The flash rate

depends on the mode and RF activity)

11: Heartbeat LED

Flashes steadily to indicate that the receiver is

functioning correctly. If the light is ON or OFF all

the time, then there could be a hardware

problem.

12: Address Switch/Option Switch (Standalone

Mode Only)

Used to assign the address of the receiver on the

network when connected to a control panel.

Options switches when used in Standalone

Mode.

Premier Elite 32XPH-W Installation Instructions

6 INS732

Mounting the Expander

Remove each screw cap by inserting a flat bladed screwdriver into the slot and turning anti-clockwise,

excessive force is NOT required. Remove both of the cover screws and put them in a safe place along with

the screw caps. Gently pull the cover away from the base applying slight pressure to the sides at the top of

the expander if required. The front cover should now be off. Mount the expander using at least two

appropriate countersunk screws (no larger than No. 8). A keyhole slot has been provided to assist mounting

and aid levelling. If required a screw should be placed into the knockout on the rear of the expander to enable

the rear/wall tamper.

Do not mount near metal or mains supplies. When using with metal control panels a minimum of 50cm gap is

required. Do not mount near aerials of any description, or other wireless equipment.

Wiring

It is strongly recommended that the system is completely powered down (mains and battery) before wiring

the expander. Connect the expander to the control panel using 4-core cable as follows:

Expander

Control Panel

Description

+12V Supply

0V Supply

Transmit Data

Receive Data

The networks are made up of four terminals incorporating power and data. To ensure correct operation, all

four terminals on the device must be connected to the corresponding terminals on the control panel or

previous device. Expanders can be connected using 4-core cable. However, it is recommended that 6 or 8-

core cable is used as the spare cores can be used to ‘Double Up’ on the power connections if needed.

Standard 7/0.2 alarm cable can be used for most installations. However, under certain conditions it may be

necessary to use screened cable.

Selecting an Address

Each expander must be assigned a different address using the DIL switches located on the PCB. The table

below shows the expander addressing:

Address

DIL 1

DIL 2

DIL 3

DIL 4

On or Off

Off

Never set two expanders on the same network to the same address. Expanders are factory set to address 1.

Premier Elite 32XPH-W Installation Instructions

INS732 7

Ricochet Expander Addressing

Introduction

The address range and switch position will depend on which combination of expanders are being used. Each

32XPH-W takes up 4 address slots on the control panel network, however the network slots are virtual until

devices are assigned to available zones. It is possible that if a 32XPH-W is being used at Address 1, but only

16 devices have been used, Address 3 & 4 are available for hardwired 8XP's.

Please see some examples of mixing different types of Expanders on various Elite panels and the addressing

requirements.

Example: Totally wireless system(s)

Panel

32XPH-W

Network 1

Network 2

Network 3

Network 4

Network 5

Network 6

Network 7

Network 8

Expanders

(Max)

Premier

Elite 88™

Exp

N/A

Expander

Address

N/A

Premier

Elite 168™

Exp

N/A

Expander

Address

N/A

Premier

Elite 640™

Exp

Expander

Address

5. Programming

Premier Elite™ V2.10> 12/24/48/88/168 Ricochet Learn Menu

V2.10> contains a dedicated Ricochet learn menu accessible via the /key when in Engineer menu.

Learn Devices from first power up

Follow the instructions given in INS176-8 or later for the first power up of the system.

When the "Confirm Devices" menu appears check and make sure all installed Keypads and Expanders are

showing; press /and /again to confirm.

Providing the system has a Ricochet®enabled expander installed, the following will appear. The flow

diagram shows the procedure to learn devices:-

Premier Elite 32XPH-W Installation Instructions

8 INS732

YES to Select:-

Learn Ricochet



Learn Device?

Zone ??? N?,E??

Power up Device!

N?,E?,D?? - 20s

Learn Device to

Zone ??? N?,E??



nnU

Access the Learn Menu using the Omit “Hot” key

From any top level engineering menu pressing the /key will take you to the Ricochet learn menu

above.

/

Ricochet Learn Menu

YES to Select:-

????????????????

/

YES to Select:-

Learn Ricochet

IMPORTANT

In all cases when entering the Learn menu the next available free Zone will be chosen to learn a device too. It

will not be possible to learn a device to a Zone that already has a device learned too it. The number of

expander’s on the system will dictate which next “free” zone is chosen to learn too.

When all device slots have been used the following screen will be shown

All Devices

Learnt!

Pressing the N/Nkey will return you to the Ricochet®learn menu; pressing the /key will enter

the Delete devices menu.

Auto Zone Type & Area

When learning devices, if no editing has taken place of the control panel on-board hardwired zones, these will

be switched to Not Used after the first Ricochet®device is learned to the system; the following defaults will

be used for Ricochet®devices learned to the system.

Zone

Type

Area

001-008

Not Used

N/A

009

Entry/Exit 1

010

Guard Access

011 & above

Guard

IMPORTANT

If any editing of any of the on board control panel zones is carried out BEFORE any Ricochet devices are

learned too the system, the control panel zones will remain at factory defaults.

Premier Elite 32XPH-W Installation Instructions

INS732 9

Deleting Devices

Delete Devices

To delete devices from the system, access the Ricochet Learn menu. Any of the methods previously detailed

may be used.

The /key is used to access the Delete option.

Follow the flow diagram to delete devices from the system.

To delete all devices, go to Engineer Utilities/Ricochet Diagnostics. Scroll to the first wireless zone for

the expander being defaulted and press /followed by /. All zones will be deleted.

YES to Select:-

Learn Ricochet



Learn Device

Zone ??? N?,E?

Delete Device?

Zone ??? N?,E?

nnU



NN

If all devices are deleted from the system the following will be shown

All Devices

Deleted!

Pressing the N/Nkey will return you to the Ricochet learn menu; pressing the /key will enter

the Learn devices menu.

Summary of Keys used

Key

Function

/

Use this key to access the Ricochet Learn menu from any top level engineering

menu.

/

Use this key when in Ricochet Learn menu to delete devices, or cycle between

learn and delete functions

N/N

Use this key to exit the Learn Menu.

Premier EliteV2.00 - V2.09 24/48/88/168 & 640 + Ricochet V2.xx

Introduction

V2.xx firmware added the option to learn Ricochet devices through the Zone Setup Menu, the "Configure

Radio" menu in Engineer's Utilities is now redundant and should only be used for Legacy systems.

Premier Elite 32XPH-W Installation Instructions

10 INS732

Learning Devices

To learn a device to a Zone select the Zone from the Zone Setup Menu, Zones that are capable of having a

Ricochet device learnt to them will be displayed as follows:-

Zone 00 P0,0

Not sed

Fig 1

Fig 1indicates the pre-assigned zone number, the expander being used and the device slot on the expander.

Once a device has been learnt the display will be as Fig 2:-

Zone 00 Learn:

PR P-0,0

Fig 2

If you are unsure if a zone already has a device learned to it, you can go to the menu as in Fig 1, press

/and then n/nif a device is already learnt the display will look like Fig 2, if not then it will

look like Fig 3

Zone 00 Learn:

ree P-0,0

Fig 3

Please see the diagram on the next page to learn devices.

Deleting Devices

To delete devices from the expander is the same as learning them; choose the zone you wish to delete, and

follow the procedure to learn the device, when the screen shows “Learning” press /.

To default the expander completely, disconnect the T and R lines, put option switch 1 & 2 to ON and hold the

white function button until the expander programming LED's all illuminate and turn off.

Device Modes of Operation

Always Awake

This mode should only be used on devices which are required to signal at all times and is the default setting

for perimeter detection devices such as Contacts and Shock sensors & PA Buttons.

Auto Mode

When in Auto Mode, devices poll at 15 minute intervals. Following activation, devices will not transmit the

same activation again for a period of 3 minutes. This mode of operation is the default mode for all single

technology motion detectors.

Hybrid Mode

Hybrid mode is used to control the reporting functions for devices. When in this mode devices are awake only

when the system is set. Devices are woken up by the control panel at the point of arming. The system will

display "Preparing to Arm". When the system is disarmed the devices will be put back to sleep. This mode of

operation is the default mode for all Dual Technology motion detectors.

On very large systems (100 devices +) a small delay may be experienced when arming the system, this is normal

as the expanders on the system wake up the relevant devices.

Premier Elite DT-W should ALWAYS be used in Hybrid mode, failure to do this will have an adverse affect on

battery life.

Device Specific Mode

Device Specific mode is used to control the reporting functions for devices. Devices that use this mode of

operation have specific operating parameters and should not be altered. This mode of operation is the default

mode for all Fire detectors (Smoke, Heat and any other variant), & Internal/External Sounders.

Tabla de contenidos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario