Texas Instruments LM74610-SQEVM Manual de usuario

LM74610-SQEVM

User's Guide

Literature Number: SNVU489

October 2015

Contents

1 Introduction......................................................................................................................... 4

2 Setup.................................................................................................................................. 4

2.1 Input/Output Connector Description ................................................................................... 4

2.2 Board Setup............................................................................................................... 5

3 Operation............................................................................................................................ 6

3.1 Reverse Polarity Protection............................................................................................. 6

3.2 Output Voltage............................................................................................................ 8

4 Board Layout..................................................................................................................... 10

5 Schematic ......................................................................................................................... 12

6 Bill of Materials .................................................................................................................. 13

2Table of Contents SNVU489–October 2015

Submit Documentation Feedback

www.ti.com

List of Figures

1 LM74610-Q1 Typical Application Circuit ................................................................................. 4

2 LM74610-SQ EVM........................................................................................................... 5

3 Response to Reverse Polarity 12V to -20V .............................................................................. 6

4 Response to Start Up Reverse Polarity................................................................................... 7

5 Periodic body diode voltage drop at the output ......................................................................... 8

6 The LM74610-SQEVM Output voltage waveform....................................................................... 9

7 Top Assembly Layer....................................................................................................... 10

8 Bottom Layer................................................................................................................ 11

9 LM74610-SQEVM Schematic ............................................................................................ 12

List of Tables

1 Device and Package Configurations ...................................................................................... 4

2 LM74610-SQ EVM Bill of Materials for Configuration................................................................. 13

SNVU489–October 2015 List of Figures

Voltage

Regulator

Anode

Vbatt LM74610-Q1

Cathode

Cout

Vcap

TVS+

Vout

TVS-

Introduction

www.ti.com

1 Introduction

The Texas Instruments LM74610-SQ Evaluation Module helps designers evaluate the operation and

performance of the LM74610-Q1 Reverse Polarity Protection Smart Diode Controller. This evaluation

module demonstrates how an N-Channel power MOSFET can emulate a very low forward voltage diode

with zero Iq and low leakage current flowing through the IC. In this design scheme the LM74610-Q1 is

combined with a MOSFET and used in series with battery as a replacement for schottky diode and PFET

in reverse polarity protection circuitry as shown in Figure 1 . For more information on the LM74610

functional and electrical characteristics, see the LM74610-Q1 Reverse Polarity Protection Smart Diode

Controller Data Sheet (LM74610).

Table 1. Device and Package Configurations

CONVERTER IC PACKAGE

U1 LM74610-Q1 VSSOP-8

2 Setup

This section describes the jumpers and connectors on the EVM as well and how to properly connect, set

up and use the LM74610-SQEVM. Ensure the power supply is turned off while making connections on the

board.

2.1 Input/Output Connector Description

•VBAT_1: Power input connector to the positive rail of the input power supply.

•GND: Battery ground connector.

•VOUT: is the power output connector to the positive side of the load.

•TEST POINTS: are also available at VBAT_1,GND,VOUT,DRV_1 (MOSFET Gate Voltage), and

VCAP_1 (Charge pump capacitor).

Figure 1. LM74610-Q1 Typical Application Circuit

4List of Tables SNVU489–October 2015

Submit Documentation Feedback

www.ti.com

Setup

2.2 Board Setup

Before applying power to the LM74610EVM, all external connections should be verified. External power

supplies should be turned off and connected with proper polarity to the VBAT_1 and GND connectors. An

electronic or resistive load must be connected at the output.. The LM74610-Q1 will not initiate the

charge pump operation if a closed loop system is in standby mode or the drain current is smaller than

1mA (typical). The tests outlined in this document 3A constant current as the load and 12V at the input

(VBAT_1). Make sure that the external power supply source for the input voltage is capable of providing

enough current to the output load so that the output voltage can be obtained.

Once all connections to the LM74610-SQEVM are verified, power can be applied to VBAT_1. The EVM

will then begin to operate.

Figure 2. LM74610-SQ EVM

SNVU489–October 2015 List of Tables

Time (100 µs/DIV)

VOUT (10 V/DIV, 12 V to 0 V)

VIN (10 V/DIV, 12 V to -20 V)

Gate Drive (10 V/DIV)

Operation

www.ti.com

3 Operation

3.1 Reverse Polarity Protection

A dynamic voltage pulse from +12V to -20V is applied at the VBAT_1 input of the LM74610-SQEVM.

Figure 3 shows when the input voltage (yellow) drops down to -20V, the output voltage (blue) does not go

negative, and therefore, the load is protected from dynamic reverse pulses at the input. The LM74610-Q1

reacts the negative voltage surge within 2μsec and shuts down the MOSFET by pulling the gate voltage to

zero (green). The output slowly decays due to the large output capacitors and increased time constant.

Figure 3. Response to Reverse Polarity 12V to -20V

6List of Tables SNVU489–October 2015

Submit Documentation Feedback

www.ti.com

Operation

A -12V source is connected to the VBAT_1 input of the LM74610-SQEVM. Figure 4 shows that the Output

voltage will stay at a constant 0V in this situation. This test simulates the event of connecting a 12V

battery in the reverse direction, and therefore, protects the load from negative voltages.

Figure 4. Response to Start Up Reverse Polarity

Note: Please note that the leakage current is 60uA (typ). This means that if you apply a voltage on the

output you will see some voltage on input and this voltage will collapse if you draw more current than the

leakage current. The same applies for a reverse voltage applied on the input.

SNVU489–October 2015 List of Tables

Operation

www.ti.com

3.2 Output Voltage

When power is initially applied, the load current (ID) will flow through the body diode of the MOSFET. This

current will produce a forward voltage drop (Vf) across the MOSFET body diode. This voltage is used to

charge up the charge pump capacitor Vcap. This periodic voltage drop will be equal to the MOSFET body

diode forward voltage drop and occurs for about 25.6msec as shown in Figure 5.

Figure 5. Periodic body diode voltage drop at the output

During the rest of the period of conduction, the LM74610-Q1 will drive the gate of the MOSFET. When the

MOSFET is ON, it provides a low resistive path for the drain current to flow and minimizes the power

dissipation associated with forward conduction. The power losses during the MOSFET ON state depend

primarily on the RDSON of the selected MOSFET and load current. The LM74610-Q1 operation keeps the

MOSFET ON at approximately 98% as shown in Figure 6, leading to very little overall power dissipation

when compared to a typical diode.

8List of Tables SNVU489–October 2015

Submit Documentation Feedback

www.ti.com

Operation

Figure 6. The LM74610-SQEVM Output voltage waveform

SNVU489–October 2015 List of Tables

Board Layout

www.ti.com

4 Board Layout

Figure 7. Top Assembly Layer

10 List of Tables SNVU489–October 2015

Submit Documentation Feedback

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TPS658643 Manual de usuario

Texas Instruments

Texas Instruments ADS8686SEVM-PDK Manual de usuario

Texas Instruments

Texas Instruments ADS8332EVMV2-PDK Manual de usuario

Texas Instruments

Texas Instruments BQ79600-Q1 Manual de usuario

Texas Instruments

Texas Instruments INA219EVM Manual de usuario

Texas Instruments

Texas Instruments TPS92518EVM Manual de usuario

Texas Instruments

Texas Instruments TPS65680 Manual de usuario

Texas Instruments

Texas Instruments TPS36Q1EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8412EVM Manual de usuario

Texas Instruments

Texas Instruments TPS2549Q1EVM-729 Manual de usuario

Texas Instruments

Texas Instruments TPS562207EVM 2-A Manual de usuario

Texas Instruments

Texas Instruments LP8756 Q1EVM Series Manual de usuario

Texas Instruments

Texas Instruments THS4503EVM Manual de usuario

Texas Instruments

Texas Instruments INA226EVM Manual de usuario

Texas Instruments

Texas Instruments bq51013xEVM Manual de usuario

Texas Instruments

Texas Instruments DS90UB96X-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments DP83869 Manual de usuario

Texas Instruments

Texas Instruments MSP-US-TRF6901 Manual de usuario

Texas Instruments

Texas Instruments LMR33630EVM Manual de usuario

Texas Instruments

Texas Instruments SimpleLink CC2650 Manual de usuario

Texas Instruments

Texas Instruments LMK04808B Manual de usuario

Texas Instruments

Texas Instruments PS62510EVM-168 Manual de usuario

Texas Instruments

Texas Instruments TPSM8286 AA0 Series Manual de usuario

Texas Instruments

Texas Instruments DACx760EMC-EVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario