Texas Instruments LDC1000 Manual de usuario

LDC1000 Evaluation Module

User's Guide

Literature Number: SNAU150

September 2013

Chapter 1

SNAU150–September 2013

LDC1000 Evaluation Module

1.1 Overview

The LDC1000 Evaluation Module is designed to provide an example LC tank and coil structure

application, to interface to a host computer. The module can be used independently of the GUI by the on-

board embedded LED, which demonstrates threshold detection.

Figure 1-1. Evaluation Module

The EVM includes an example PCB sensor which is 14mm in diameter and contains 2 layers. A 100pF

1% COG cap is connected, in parallel, to the PCB coil, in order to form an LC tank.

The EVM is perforated at two locations: One between Coil and LDC1000, which provides the option to

snap the PCB coil and connect a custom coil required in the application. The second perforation is

between LDC1000 and MSP430, and provides the option to connect the LDC1000+Sensor into a different

system or use multiple of such sensors in one system for prototyping.

Figure 1-2. LDC1000+Sensor

When the evaluation module first powers up from the USB port, it will flash a series of green and red LED

lights to indicate self-test. When self-test is finished, the green LED indicates the status of the LDC1000

INT pin. When INT is asserted, the green LED is lit. By default, INT is configured for threshold detection.

2LDC1000 Evaluation Module SNAU150–September 2013

Submit Documentation Feedback

Chapter 2

SNAU150–September 2013

Quick Start Guide LDC1000 Evaluation Module

2.1 LDC1000 Evaluation Module Overview

The LDC1000 Evaluation Module (EVM) enables the user to test out analog and digital capabilities of the

LDC1000 Inductance-to-Digital Converter. The EVM is a USB device used with a host computer and

accessed using the Inductive Sensing Graphical User Interface (GUI) software, which is documented in

Chapter 3.

To quickly get started on the LDC1000 GUI, follow the steps below to load and configure a device.

2.1.1 Evaluation Module

Set Up Requirements

1. The LDC1000 GUI and drivers must be installed on the host.

2. The USB port of the EVM must be connected to the host.

Loading and Running

1. Plug the EVM into the host computer. The host computer should automatically detect the device as

LDC1000EVM.

2. Launch the GUI. It should automatically detect the target, read all the configuration registers, and begin

streaming data.

Figure 2-1. Streaming Section

SNAU150–September 2013 Quick Start Guide LDC1000 Evaluation Module

LDC1000 Evaluation Module Overview

www.ti.com

Reloading the Device

If the EVM is disconnected from the host at any time, simply reconnect the device and the GUI will

automatically discover and re-establish the streaming abilities with the device.

Configuring the Device Manually

1. The GUI puts the device in streaming mode by default. Click on "Stop" in the Streaming Section to

stop streaming.

Figure 2-2. Stop Streaming

2. Click on the "Configuration Section" icon in the main window toolbar.

Figure 2-3. Configuration Section Icon

3. Select the parameter to change. When entering the comparator thresholds, press ENTER to confirm

the change. Changes are applied immediately.

4Quick Start Guide LDC1000 Evaluation Module SNAU150–September 2013

Submit Documentation Feedback

www.ti.com

LDC1000 Evaluation Module Overview

Figure 2-4. Configuration Section

Saving Device Configuration

1. Click on the "Save" icon in the toolbar.

Figure 2-5. Save Icon

2. Type a name for the file.

Configuring the Device with Configuration File Defaults

1. The GUI puts the device in streaming mode by default. Click on "Stop" in the Streaming Section to

stop streaming.

2. Click on the "Open" icon in the toolbar.

Figure 2-6. Open Icon

3. Select the configuration file.

SNAU150–September 2013 Quick Start Guide LDC1000 Evaluation Module

LDC1000 Evaluation Module Overview

www.ti.com

4. After the configuration file is loaded, current values are written once to all supported registers. To

restore defaults defined in the configuration file, click on Restore Defaults to write all current registers

with the new configuration file defaults.

Figure 2-7. Restore Defaults

6Quick Start Guide LDC1000 Evaluation Module SNAU150–September 2013

Submit Documentation Feedback

Chapter 3

SNAU150–September 2013

Inductive Sensing GUI User Guide

3.1 Inductive Sensing GUI Overview

The inductive sensing GUI provides graphical configuration and streaming support for the LDC1000. The

GUI package includes drivers for use with the LDC1000 Evaluation Modules (EVM). The EVM

provides a device abstraction layer for the GUI to communicate with the LDC1000 through SPI, and

includes other extended functionality.

3.2 Host platform Requirements

The Inductive Sensing GUI supports:

• 32-bit and 64-bit Windows 7

• 32-bit and 64-bit Windows XP

The host machine is required for device configuration and data streaming.

3.3 EVM Information

For the TI LDC1000 EVM:

• The EVM allows the GUI to:

– Configuring register data through SPI (CSB, SCLK, SDO, SDI)

– Stream register data through SPI

– Detect interrupts through SPI

3.4 Hardware Setup

Below are the steps which are necessary to prepare the EVM for the GUI:

• The GUI must be installed on the host.

• The EVM driver must be installed on the host.

• The EVM must be connected to a full speed USB port (1.0 or above).

3.5 Icon Toolbar

The icon toolbar contains various icons which navigate between sections and perform various functions.

Figure 3-1. Icon Toolbar

SNAU150–September 2013 Inductive Sensing GUI User Guide

Connecting and Disconnecting

www.ti.com

Name Description Icon

Connection Information Indicates whether an EVM is connected to • EVM is connected

the PC, and if so, provides details of the

connected device.

• EVM is disconnected

Open Opens saved register settings and

defaults

Save Saves all current register settings and

defaults

Configuration Show Configuration Section

Streaming Show Streaming Section

3.6 Connecting and Disconnecting

Device discovery, connection, and disconnection is performed automatically.

3.7 Multiple EVMs

If the user desires to connect to multiple EVMs, multiple instances of the GUI can be launched. Multiple

instances cannot connect to the same EVM; only one instance of the GUI can be connected to one EVM.

3.8 General Configuration

In the configuration section, all registers of the device can be accessed. To access this section, streaming

must be stopped.

8Inductive Sensing GUI User Guide SNAU150–September 2013

Submit Documentation Feedback

www.ti.com

Figure 3-2. Configuration Section

In the configuration window, select the parameter to change. When entering the comparator thresholds,

press ENTER to confirm the change. Changes are applied immediately.

Press “Read All” to refresh all configuration, status, and data.

Press “Restore Defaults” to write values from the default column (if they exist) to the current register value.

3.9 Register Settings

In the register settings section, all registers of the device can be accessed. To read/write registers,

streaming must be stopped.

SNAU150–September 2013 Inductive Sensing GUI User Guide

Data Streaming

www.ti.com

Figure 3-3. Register Settings

Double-click on a register in the table to read/write. If a register is read only, the selected register is read

immediately and the table value updated. If the register is read/write, a dialog pops up and the user can

choose a new register value. If the value is not changed, it will default to a read.

Figure 3-4. Read/Write Register Dialog

Press “Read All” to refresh all configuration, status, and data.

Press “Restore Defaults” to write values from the default column (if they exist) to the current register value.

3.10 Data Streaming

Data is streamed from the EVM to the GUI when streaming is started. The sampling rate of the EVM and

the number of samples to plot can be configured.

10 Inductive Sensing GUI User Guide SNAU150–September 2013

Submit Documentation Feedback

Otros manuales para LDC1000

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TPS92830-Q1 Manual de usuario

Texas Instruments

Texas Instruments DAC8775EVM Manual de usuario

Texas Instruments

Texas Instruments ADS1278V2EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments TPS92515HVEVM-749 Manual de usuario

Texas Instruments

Texas Instruments LMP90100 Manual de usuario

Texas Instruments

Texas Instruments TMP006EVM Manual de usuario

Texas Instruments

Texas Instruments BoosterPack BOOST-ADS7042 Manual de usuario

Texas Instruments

Texas Instruments BOOSTXL-DRV8305EVM Manual de usuario

Texas Instruments

Texas Instruments ADS54J69EVM Manual de usuario

Texas Instruments

Texas Instruments TMAG5124EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8703-Q1 Manual de usuario

Texas Instruments

Texas Instruments XTR300EVM Manual de usuario

Texas Instruments

Texas Instruments TPA3200D1 Manual de usuario

Texas Instruments

Texas Instruments OPA455EVM Manual de usuario

Texas Instruments

Texas Instruments TMS320C3 Series Manual de usuario

Texas Instruments

Texas Instruments LMG3410EVM-031 Manual de usuario

Texas Instruments

Texas Instruments DS90UB933-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments ADS1x20EVM Manual de usuario

Texas Instruments

Texas Instruments OPA928 Manual de usuario

Texas Instruments

Texas Instruments TPD3S714-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments DLP4710EVM-LC Manual de usuario

Texas Instruments

Texas Instruments DRV604PWPEVM Manual de usuario

Texas Instruments

Texas Instruments TPS25921XEVM-637 Manual de usuario

Texas Instruments

Texas Instruments LMK04906 Series Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario