Texas Instruments DLP LightCrafter Display 3010 Manual de usuario

User's Guide

DLPU029A–October 2014–Revised January 2015

DLP®LightCrafter™ Display 3010 EVM User’s Guide

Topic ........................................................................................................................... Page

1 DLP®LightCrafter™ Display 3010 EVM Overview..................................................... 2

2 Applicable Documents.......................................................................................... 2

3 What is in the LightCrafter Display 3010 EVM.......................................................... 3

4 Light Engine........................................................................................................ 4

5 Quick-Start Procedure.......................................................................................... 4

6 Circuit Description ............................................................................................... 5

7 EVM Setup .......................................................................................................... 8

DLPU029A–October 2014–Revised January 2015 DLP®LightCrafter™ Display 3010 EVM User’s Guide

DLP®LightCrafter™ Display 3010 EVM Overview

www.ti.com

1 DLP®LightCrafter™ Display 3010 EVM Overview

This user’s guide presents an overview of the DLP LightCrafter Display 3010 evaluation module (EVM)

and a general description of the main features and functions. It will explain the first steps to get started,

shows a detailed description of the push buttons function, the on board LEDs and the main connectors. It

will give the user a successful start with his first DLP LightCrafter Display 3010 evaluation module.

Figure 1. DLP LightCrafter Display complete EVM

In addition to this document, the following documents shown in Section 2 should be used.

2 Applicable Documents

The following documents are applicable to the DLP LightCrafter™ Display 3010 EVM and are available at

TI.com www.ti.com.

• DLP3010 (.3 720p) DMD data sheet, TI literature number DLPS051

• DLPC3438 controller data sheet, TI literature number DLPS035A

• Software Programmer's Guide, TI literature number DLPU020A

• DLP LightCrafter Display EVM GUI Tool User's Guide, TI literature number DLPU021

If you need assistance refer to the DLP and MEMS TI E2E community support forums. forums.

LightCrafter is a trademark of Texas Instruments.

DLP is a registered trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

2DLP®LightCrafter™ Display 3010 EVM User’s Guide DLPU029A–October 2014–Revised January 2015

Submit Documentation Feedback

www.ti.com

What is in the LightCrafter Display 3010 EVM

3 What is in the LightCrafter Display 3010 EVM

The DLP LightCrafter Display module consists of three subsystems:

• Light engine – includes the optics, red, green, and blue LEDs, and a 1280 × 720 (720p) DMD capable

of 300 lumens out-of-the-box.

• Driver board – includes the DLP chipset comprising of DLPC3438 Controller and DLPA2005

PMIC/LED driver.

• System board – includes MSP430, ITE HDMI receiver, USB-Serial Bridge controller and several

connectors for external inputs (HDMI, USB, etc.)

Figure 2. DLP LightCrafter Display EVM Block Diagram

DLPU029A–October 2014–Revised January 2015 DLP®LightCrafter™ Display 3010 EVM User’s Guide

80.35

56.97

21.00

20.50

Light Engine

www.ti.com

4 Light Engine

The optical engine in the EVM is developed by eProtech and is production ready.

The light engine consists of the following components:

• 0.3-inch 720p DMD (DLP3010)

• OSRAM red, green and blue LED

Table 1. Optical Engine specifications

Parameter Min Typ Max Unit

Brightness 125 Lum

LED Current 2.4 A

Brightness Uniformity 75%

Throw Ratio 1.65

Offset 100%

Focus Range 5 50 inch

Image diagonal size 5 50 inch

Figure 3.

5 Quick-Start Procedure

This quick-start assumes default conditions as shipped.

1. Power up the DLP LightCrafter™ Display 3010 EVM by applying an external DC power supply (5 V

DC, 3.0 A) to the J12 connector. Note: Use an AC-DC switching power supply which accepts 50-60Hz

100-240 VAC inputs, and outputs a nominal 5 VDC at maximum 3 A output current. The PWRON

(D16) and SYSPWR (D15) LED will turn on to indicate that 5 V power is applied

2. Move the SW_ONOFF switch to the ON position to turn the DLP LightCrafter Display 3010 EVM on.

When the LightCrafter Display 3010 EVM is turned on, the PROJ_ON LED will turn on.

3. After the DLP LightCrafter Display 3010 EVM is turned on; the projector will default to displaying a DLP

LightCrafter Display splash image.

4. The focus of the image can be adjusted on the optical engine.

4DLP®LightCrafter™ Display 3010 EVM User’s Guide DLPU029A–October 2014–Revised January 2015

Submit Documentation Feedback

Focus

Adjustment

www.ti.com

Circuit Description

Figure 4. Optical engine with focus adjustment

5. Connect USB to the LightCrafter™ Display 3010 EVM and open the GUI on your Computer. If needed

connect a HDMI source to the EVM and communicate to the EVM over the GUI software.

6. When turning off the projector, turn off the SW_ONOFF switch prior to removing power cable. Note: To

avoid potential damage to the DMD it is recommended to turn off the projector with the SW_ONOFF

before disconnecting the power.

7. There are ten indicator LEDs on the DLP LightCrafter Display 3010 EVM (Table 2):

Table 2. LEDs on the DLP LightCrafter Display 3010 EVM

D15 SYSPWR 5 V Power applied

D16 PWRON Regulated 3V3 power on

D7 PROJ_ON On when Projector is turned on via SW_ONOFF

D6 RESETZ OFF when Projector is turned on vie SW_ONOFF

ON during DLPC3438 boot OFF when projector is

D5 HOST_IRQ running. Indication of DLPC3438 boot-up

completed and ready to receive commands

ON when HDMI cable plugged in, and external

D9 MSP2 video detected. OFF when external video is not

detected.

ON when Cypress CY3420 is I2C master OFF

D8 ACK when MSP430 is I2C master

ON when Cypress CY3420 requests the MSP430

D10 REQ to give Cypress master control of the I2C bus

Blinking when PC is communicating to flash over

D12 GPIO1 SPI

Blinking when PC is communicating to DLPC3438

D14 GPIO0 over I2C

6 Circuit Description

6.1 Connectors, Switch and Push buttons on Main Board

Table 3. List of installed Connectors on the main board

Installed Connectors/Headers Description

J12 Connector for 5 V external power supply interface

J7 Connector for USB cable

J2 Connector for Audio

J4 Connector for HDMI input

J1 MSP430 JTAG Programming interface connector

J13 Connector for the I2C interface (DevaSys box)

J6 60 pin connector for DLP LightCrafter Display board

J10 Header for 5 V DC power

DLPU029A–October 2014–Revised January 2015 DLP®LightCrafter™ Display 3010 EVM User’s Guide

Circuit Description

www.ti.com

Table 3. List of installed Connectors on the main board (continued)

Installed Connectors/Headers Description

J11 Header for 5 V DC power

J3 Unsupported

J5 Unsupported

Table 4. List of installed Push buttons and Switch on main board

Installed Switches/Push buttons Description

SW1 Projector On/OFF Switch

Source Selection

• First press: TPG

PB-UP1 • Second press: HDMI input

• Third press: Splash screen

PB-SEL1 Cycle through displaying 7 curtain colors

PB-DOWN1 Flip image N/S or E/W

Cycle 9 different TPG patterns after TPG source selected

PB_LEFT1 Cycle 4 different Splash screens after Splash source selected

Change of Volume when HDMI input is selected

Change LED current total 7 steps

PB_RIGHT1 Change of Volume when HDMI input is selected

6DLP®LightCrafter™ Display 3010 EVM User’s Guide DLPU029A–October 2014–Revised January 2015

Submit Documentation Feedback

www.ti.com

Circuit Description

6.2 Connectors on DLP LightCrafter Display board

Table 5. List of installed Connectors on the DLP LightCrafter™ Display board

Installed Switches/Push buttons Description

J1 Connector for the DMD flex cable

J2 Connector for LED cable

J3 Connector for external temperature sensor (Requires removing R21)

J4 Connector for light sensor

J5 Future use

J6 60 pin connector for DLP LightCrafter Display board

DLPU029A–October 2014–Revised January 2015 DLP®LightCrafter™ Display 3010 EVM User’s Guide

Audio

Interface

Projector

ON/OFF

Switch

HDMI

Connector

5V Power

Connector

DLP

LightCrafter™

Display Board

Connector

USB

Connector

EVM Setup

www.ti.com

7 EVM Setup

The DLP LightCrafter Display 3010 EVM is composed of three parts:

• Main board

• DLP LightCrafter Display board

• Engine with LED connection and Flex cable

The main board contains the connector for the power supply, a USB connector to communicate to the

DLP LightCrafter™ Display software, HDMI, audio and the connector for the DLP LightCrafter™Display

board. The main board also contains a switch to turn on the projector in case the DLP LightCrafter™

Display board and the engine are connected. Figure 5 shows the main connectors on the main board.

Figure 5. DLP LightCrafter Display main board

The DLP LightCrafter™ Display board has three main connectors: the LED connector, the Flex cable

connector, and the main board connector. To connect the main board to the DLP LightCrafter™ Display

board, refer to Figure 6. Note that the main board connector on the DLP LightCrafter™ Display board is

on the bottom while the LED and Flex cable connectors are on the top.

8DLP®LightCrafter™ Display 3010 EVM User’s Guide DLPU029A–October 2014–Revised January 2015

Submit Documentation Feedback

LED

Connector

Flex Cable

Connector

www.ti.com

EVM Setup

Figure 6. Connection Main Board and DLP LightCrafter Display board

The board itself and how it gets connected to the main board is shown in Figure 7

Figure 7. DLP LightCrafter Display

TA LED adapter board is connecting the three LEDs with the LED connector on the DLP LightCrafter™

Display board. The different connectors for each LED are named on the board as well as on the light

engine. Refer to Figure 8 to see the proper setup.

Ensure a good connection of the flex cable to the DLP LightCrafter™ Display board before turning it on.

DLPU029A–October 2014–Revised January 2015 DLP®LightCrafter™ Display 3010 EVM User’s Guide

EVM Setup

www.ti.com

Figure 8. LED Connection

Figure 9 shows the final setup of all parts.

Figure 9. DLP LightCrafter Display complete EVM

Make sure that everything is setup correctly before continuing! Verify that the flex cable is connected

correctly to the LightCrafter Display board.

10 DLP®LightCrafter™ Display 3010 EVM User’s Guide DLPU029A–October 2014–Revised January 2015

Submit Documentation Feedback

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments THS3062EVM Manual de usuario

Texas Instruments

Texas Instruments ADS7861EVM Manual de usuario

Texas Instruments

Texas Instruments TLIN1021 EVM Manual de usuario

Texas Instruments

Texas Instruments RS485-HF-DPLX-EVM Manual de usuario

Texas Instruments

Texas Instruments bq24750A Manual de usuario

Texas Instruments

Texas Instruments AM572x series Manual de usuario

Texas Instruments

Texas Instruments SCAU020 Manual de usuario

Texas Instruments

Texas Instruments LM10502 Manual de usuario

Texas Instruments

Texas Instruments LMX2430 Manual de usuario

Texas Instruments

Texas Instruments DS320PR810-RSC-EVM Manual de usuario

Texas Instruments

Texas Instruments TAS5508-5142K7EVM Manual de usuario

Texas Instruments

Texas Instruments LM7480-Q1 Manual de usuario

Texas Instruments

Texas Instruments TPA6020A2 Manual de usuario

Texas Instruments

Texas Instruments TPS7A10EVM-004 Manual de usuario

Texas Instruments

Texas Instruments TPS566235EVM-036 Manual de usuario

Texas Instruments

Texas Instruments BOOST-LDC3114EVM Manual de usuario

Texas Instruments

Texas Instruments PGA112EVM Manual de usuario

Texas Instruments

Texas Instruments bq2589EVM Manual de usuario

Texas Instruments

Texas Instruments TCA6507EVM Manual de usuario

Texas Instruments

Texas Instruments ADS64XX EVM Manual de usuario

Texas Instruments

Texas Instruments TPS62125EVM-044 Manual de usuario

Texas Instruments

Texas Instruments ADS42B4x EVM Manual de usuario

Texas Instruments

Texas Instruments TPS70151 Series Manual de usuario

Texas Instruments

Texas Instruments Stellaris LM4F120 LaunchPad Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario