Texas Instruments Bq51013AEVM-765 Manual de usuario

User's Guide

SLUU911–June 2012

bq51013AEVM-765 Evaluation Module

The bq51013AEVM-765 wireless power receiver evaluation kit from Texas Instruments is a high-

performance, easy-to-use development kit for the design of wireless power solutions. Consisting of a 5-V

power supply receiver and associated magnetics, the kit enables designers to speed the development of

their end-applications.

Contents

1 Applications .................................................................................................................. 2

2 bq51013AEVM-765 Electrical Performance Specifications ........................................................... 2

3 Modifications ................................................................................................................. 2

4 Connector and Test Point Descriptions .................................................................................. 2

4.1 Input/Output Connections ......................................................................................... 2

4.2 Jumpers/Switches .................................................................................................. 3

4.3 Test Point Descriptions ............................................................................................ 3

5 Schematic and Bill of Materials ........................................................................................... 5

6 Test Setup ................................................................................................................... 6

6.1 Equipment ........................................................................................................... 6

6.2 Equipment Setup ................................................................................................... 7

6.3 Load Step ........................................................................................................... 8

6.4 Load Dump ......................................................................................................... 9

6.5 V-Adapter Input ..................................................................................................... 9

6.6 Start-Up ............................................................................................................ 10

6.7 Disable Shutdown ................................................................................................ 10

6.8 System Efficiency ................................................................................................. 11

6.9 Dynamic Rectifier Control / Dynamic Efficiency Scaling .................................................... 11

7 Layout Guidelines ......................................................................................................... 12

8 bq51013AEVM-765 Assembly Drawings and Layout ................................................................. 13

9 Reference ................................................................................................................... 16

List of Figures

1 HPA765AEVM Schematic ................................................................................................. 5

2 Equipment Setup............................................................................................................ 7

3 Load Step, 0 mA to 500 mA............................................................................................... 8

4 Load Dump, 500 mA to 0 mA ............................................................................................. 9

5 V-Adapter Input.............................................................................................................. 9

6 Start-Up..................................................................................................................... 10

7 Equipment Shutdown Wireless Disable ................................................................................ 10

8 bq51013AEVM-765 Efficiency vs Output Power ...................................................................... 11

9 bq51013AEVM-765 V-rect vs Output Power........................................................................... 11

10 QFN Layout ................................................................................................................ 12

11 Top Assembly.............................................................................................................. 13

12 Top Copper Layer......................................................................................................... 14

13 Bottom Copper Layer .................................................................................................... 15

14 Bottom Assembly.......................................................................................................... 16

bqTESLA is a trademark of Texas Instruments.

SLUU911–June 2012 bq51013AEVM-765 Evaluation Module

Applications

www.ti.com

List of Tables

1 bq51013AEVM-765 Electrical Performance Specifications ........................................................... 2

2 Bill of Materials.............................................................................................................. 6

1 Applications

The bq51013AEVM-765 evaluation module (EVM) demonstrates the receiver portion of the bqTESLA™

wireless power system. This receiver EVM is a complete receiver-side solution that produces 5 V out at up

to 1 A when coupled with the bqTESLA™ transmitter. The bq51013AEVM-765 device shown on this EVM

along with external components that support the device for a complete solution.

• The bqTESLA™ receiver can be used in any number of low-power battery portable devices as a power

source for charging. With contact-free charging capability, no connections to the device are needed.

• Output voltage of 5 V up to 1 A

• External adapter switchover and control circuit

• Low-profile, external pick-up coil

• Frame is configured to provide correct receiver to transmitter spacing.

• Room above coil for testing with battery, key for tuning

• Adjustable resistor R16 can be used to set max output current

2 bq51013AEVM-765 Electrical Performance Specifications

Table 1 provides a summary of the bq51013AEVM-765 performance specifications. All specifications are

given for an ambient temperature of 25°C.

Table 1. bq51013AEVM-765 Electrical Performance Specifications

Parameter Notes and Conditions Min Typ Max Unit

INPUT CHARACTERISTICS

VIN Input Voltage Typical V-rectified voltage at TP12 4 5.5 8 V

VADAPTER Adapter Input Voltage 4 7 20 V

Input Overvoltage Voltage at V-rectified 15 V

OVP Protection

OUTPUT CHARACTERISTICS

VOUT V J3 to J4 5 V

IOUT I J3 1 A

SYSTEMS CHARACTERISTICS

FSSwitching Frequency 110 205 kHz

Eff Efficiency Output current 500 mA 74 %

3 Modifications

See the data sheet (SLUSAY6) when changing components. To aid in such customization of the EVM, the

board was designed with devices having 0603 or larger footprints. A real implementation likely occupies

less total board space.

Note that changing components can improve or degrade EVM performance.

4 Connector and Test Point Descriptions

4.1 Input/Output Connections

The connections points are described in the following paragraphs.

2bq51013AEVM-765 Evaluation Module SLUU911–June 2012

Submit Documentation Feedback

www.ti.com

Connector and Test Point Descriptions

4.1.1 J1 – AD External Adapter Input, J2-GND

Power can be provided to simulate an external adapter applied to the receiver. When this is done, an End

Power Transfer signal is sent to the transmitter which enters a low power state. External adapter voltage

must be a minimum of 4 V but not exceed 20V.

4.1.2 J3 – Output Voltage, J4-GND

Output voltage is 5 V in wireless power mode up to 1 A or adapter voltage if adapter is used.

4.1.3 J5 – TS and Return Connector

External connection for Temperature Sense Resistor, see data sheet for additional info.

4.1.4 J6 – Programming Connector

This connector is only useful at factory level.

4.2 Jumpers/Switches

The control jumpers are described in the following paragraphs.

4.2.1 JP1 – EN1 Enable 1

One of two Enable signals that controls the Adapter and Wireless power transfer. Low on EN1 enables the

wireless power transfer; High disables the wireless power transfer. The Default Shorting jumper setting is

Low.

4.2.2 JP2 – EN2 Enable 2

One of two Enable signals that controls the Adapter and Wireless power transfer. Low on EN2 enables the

adapter power transfer also High disables Comm-IILIM . Default Shorting jumper setting is Low.

4.2.3 JP3 – TS Enable or Disable

This jumper enables the TS adjustment feature using R3. The Disable position sets voltage at the TS pin

to a safe value. The Default Shorting jumper setting is disabled

4.2.4 JP4 – Pull-Up to Out or Vz

EN1 and EN2 pull-up along with LED D1 can be powered from OUT or RECT. Vz is derived from RECT

through a resistor and zener diode.

4.2.5 JP5 – CS100 TS Enable or Disable

Only used for bq51014 device. This jumper along with R14 and R13 will enable the Charge Status 100%

feature. See data sheet for additional info. Open will disable.

4.2.6 JP6 – ILIM Fix or ADJ

Max output current is set by I-lim pin. In the FIX position current is set to 1.2A max. In the ADJ position

current is set by R16.

4.3 Test Point Descriptions

The test points are described in the following paragraphs.

4.3.1 TP1 – AD_EN

This push-pull driver for the external PFET connects the Adapter and the Output from the bq51013.

SLUU911–June 2012 bq51013AEVM-765 Evaluation Module

Connector and Test Point Descriptions

www.ti.com

4.3.2 TP2 – AC Input 2

This is the test point for measuring ac voltage applied to the EVM from the receiver coil.

4.3.3 TP3 – Com2 Communication 2 Drive

Communication driver signal, open-drain output connected to communication capacitor.

4.3.4 TP4 – AC Input 1

This is the test point for measuring ac voltage applied to the EVM from the receiver coil.

4.3.5 TP5 – CLMP 1

Overvoltage clamp driver signal, open-drain output is connected to OVP capacitor.

4.3.6 TP6 – CLMP 2

Overvoltage clamp drive signal, open-drain output is connected to OVP capacitor.

4.3.7 TP7 – OUT Output Voltage

This test point is the output voltage from the bq51013 or the Adapter input.

4.3.8 TP8 – Boot-1 Boot Capacitor

This bootstrap capacitor 1 drive connects to the integrated circuit (IC).

4.3.9 TP9 – Boot-2 Boot Capacitor

This bootstrap capacitor 2 drive connects to the IC.

4.3.10 TP10 – CHG Charge

This output signal indicates that the output current is being delivered to OUT, the open-drain output.

4.3.11 TP11 – AC1 IC input

This is the ac input to the IC from series capacitors.

4.3.12 TP12 – Rectified Voltage

The input ac voltage is rectified into unregulated dc voltage; additional capacitance is used to filter the

voltage before the regulator.

4.3.13 TP13, TP14, TP15 – GND

These are the ground test points.

4.3.14 TP16 – TS Temp Sensor

This is the connection point for external thermistor; see the data sheet for additional information.

4.3.15 TP17 – FOD

Input for rectified power measurment, pin 14 of the IC.

4.3.16 TP18– ILIM

Programming pin for over current limit, pin 12 of the IC.

4bq51013AEVM-765 Evaluation Module SLUU911–June 2012

Submit Documentation Feedback

www.ti.com

Schematic and Bill of Materials

5 Schematic and Bill of Materials

NOTE: For Reference Only, See Table 2 for Specific Values

Figure 1. HPA765AEVM Schematic

SLUU911–June 2012 bq51013AEVM-765 Evaluation Module

Test Setup

www.ti.com

Table 2. Bill of Materials

COUNT RefDes Value DESCRIPTION SIZE Part Number MFR

1 U1 bq51013ARHL IC, bq51013A Wireless Power Receiver QFN-20 bq51013ARHL TI

1 Q1 CSD75205W1015 MOSFET, Dual PChan, -20V, 1.2A, CSP CSD75205W1015 TI

190 milliOhm 1x1.5mm

2 C1, C2 68nF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

1 C3 47nF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

1 C4 1800pF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

1 C5 100pF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

4 C6, C16, C18, 0.1uF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

C19

2 C7, C17 1.0uF Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std

2 C8, C13 22nF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

2 C9, C12 0.47uF Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std

2 C10, C11 0.01uF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std

2 C14, C15 10uF Capacitor, Ceramic, 25V, X5R, 10% 1206 Std Std

1 C20 1.0uF Capacitor, Ceramic, 50V, X5R, 10% 0805 Std Std

1 D1 LTST-C190GKT Diode, LED, Green, 2.1-V, 20-mA, 6-mcd 0603 LTST-C190GKT Lite On

1 D2 5.1V Diode, Zener, 5.1V, 300mW SOD-523 BZT52C5V1T Diodes, Inc.

0 R1, R5, R14 Open Resistor, Chip, 1/16W, 1% 0603 STD STD

1 R2 140 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 R3 200k Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-204LF Bourns

Top-Adjust

1 R4 110 Resistor, Chip, 1/16W, 1% 0603 Std Std

0 R6, R12 Open Resistor, Metal Film, 1/4 watt, ± 1% 1206 CRCW120624R0FKEA Vishay

1 R7 1.50K Resistor, Chip, 1/16W, 1% 0603 Std Std

2 R8, R9 200 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 R10 499 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 R11 10.0k Resistor, Chip, 1/16W, 1% 0603 Std Std

1 R15 110K Resistor, Chip, 1/16W, 1% 0603 Std Std

0 R13 Open Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-203LF Bourns

Top-Adjust

1 R16 5k Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-502LF Bourns

Top-Adjust

1 Coil, RX with Attractor IWAS-4832FF-50 or Vishay or

WR-483250-15M2-G or TDK or

760308201 Wurth

6 Test Setup

6.1 Equipment

6.1.1 bqTESLA™ Transmitter

Power for the bq51013AEVM-765 receiver EVM is supplied through a bqTESLA™ transmitter

(bq500210EVM-689) or WPC-certified transmitter. The input ac voltage is applied to the receiver through

the coil located in the receiver bottom.

6.1.2 Voltage Source

Input power supply to the bqTESLA™ transmitter(bq500210EVM-689) is typically 19 Vdc ±200 mV at 500

mA maximum, but consult transmitter specification. To simulate an external adapter, an additional 5 V at

the 1-A power supply is used.

6bq51013AEVM-765 Evaluation Module SLUU911–June 2012

Submit Documentation Feedback

-V

Wireless

Transmitter

LPLS

AC1

OUT-J3

VRECT-TP12

AC2

GND-J4

OUT-TP7

Wireless Receiver

bq51013AEVM-765

GND-J2V-adapter-J1

www.ti.com

Test Setup

6.1.3 Meters

Output voltage can be monitored at TP7 with a voltmeter. Input current into the load must be monitored

with an appropriate ammeter. Transmitter input current and voltage can be monitored also but the meter

must use averaging function for reducing error due to communications packets.

6.1.4 Loads

A single load is required for 5 V with a maximum current of 1 A. The load can be resistive or electronic.

6.1.5 Oscilloscope

A multichannel oscilloscope with appropriate probes is used to observe the RECT voltage at TP12 and

other signals.

6.1.6 Recommended Wire Gauge

For proper operation, 22 AWG wire is recommended when connecting the bq51013AEVM-765EVM to

loads.

6.2 Equipment Setup

• With the power supply off, connect supply to the bqTESLA™ transmitter.

• Place the bqTESLA™ receiver on the transmitter.

• Connect load to J3 with return to J4, monitor current through load with ammeter, and monitor current to

load at TP7.

• Typical output voltage is 5 V, and the output current range is 0 mA to 1 A.

6.2.1 Equipment Setup Diagram

The diagram of Figure 2 shows the equipment test setup.

Figure 2. Equipment Setup

SLUU911–June 2012 bq51013AEVM-765 Evaluation Module

V-RECT

TP7 5V-OUT

I-OUT

Test Setup

www.ti.com

6.2.2 EVM Setup Procedures

This section guides the user through a few general test procedures to exercise the functionality of the

presented hardware. A few key notes:

• To probe the output voltage of the receiver, connect the probe to TP7.

• To probe the rectifier voltage, connect the probe to TP12.

• The V-adapter supply which simulates an external adapter is connected to J1.

• All voltmeters must be Kelvin connected (at the pin) to the point of interest.

• The output load is recommended to be a variable power resistor or electronic load.

6.3 Load Step

The procedure for load step is as follows:

• Set up the test bench as described in Section 6.2.

• Power TX with 19 V.

• Provide a load step from no load (high impedance) to 10 Ωor 500 mA (if using a current source load).

• Monitor load current, rectifier voltage, and output voltage as shown in the following illustrations.

Figure 3. Load Step, 0 mA to 500 mA

8bq51013AEVM-765 Evaluation Module SLUU911–June 2012

Submit Documentation Feedback

V-RECT

TP7 5V-OUT

V-ADAPTER

V-RECT

TP7 5V-OUT

I-OUT

www.ti.com

Test Setup

6.4 Load Dump

The procedure for load dump is as follows:

• Set up the test bench as described in Section 6.2.

• Power TX with 19 V.

• Provide a load dump from 10 Ωor 500 mA (if using a current source load) to no load (high

impedance).

• Monitor load current, rectifier voltage, and output voltage as shown in the following illustration.

Figure 4. Load Dump, 500 mA to 0 mA

6.5 V-Adapter Input

The procedure for external adapter (wired adapter) testing is as follows:

• Set up the test bench as described in Section 6.2.

• Power TX with 19 V

• Apply a 6-V V-adapter input voltage.

• Monitor load current, rectifier voltage, output voltage, and V-adapter voltage as shown in the following

illustration.

Figure 5. V-Adapter Input

SLUU911–June 2012 bq51013AEVM-765 Evaluation Module

V-RECT

TP7 5V-OUT

EN1

I-OUT

V-RECT

TP7 5V-OUT

TP2 AC-IN

Test Setup

www.ti.com

6.6 Start-Up

The procedure demonstrates start-up:

• Set up the test bench as described in Section 6.2.

• Power TX with 19 V.

• Trigger scope sweep on TP2 AC IN.

Figure 6. Start-Up

6.7 Disable Shutdown

The jumper JP1 (EN1) sends an End Power Transfer to Transmitter, Shutdown:

• With unit operating normally, move jumper JP1 from Low to High position.

• LED D1 turn OFF; output voltage drops to 0 V.

• Return jumper to Low position, RX restarts.

Figure 7. Equipment Shutdown Wireless Disable

10 bq51013AEVM-765 Evaluation Module SLUU911–June 2012

Submit Documentation Feedback

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments INA219EVM Manual de usuario

Texas Instruments

Texas Instruments TIDA-050026-23882 Guía

Texas Instruments

Texas Instruments bq24190 Manual de usuario

Texas Instruments

Texas Instruments ADS54J40EVM Manual de usuario

Texas Instruments

Texas Instruments BQ25616 Manual de usuario

Texas Instruments

Texas Instruments LMR33640EVM Manual de usuario

Texas Instruments

Texas Instruments TPA6120A2 Manual de usuario

Texas Instruments

Texas Instruments ISO5500EVM Manual de usuario

Texas Instruments

Texas Instruments DSP-Codec Manual de usuario

Texas Instruments

Texas Instruments TPS63802EVM Manual de usuario

Texas Instruments

Texas Instruments ADS1x20EVM Manual de usuario

Texas Instruments

Texas Instruments TAS2770 Manual de usuario

Texas Instruments

Texas Instruments INA281EVM Manual de usuario

Texas Instruments

Texas Instruments ADS8688EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments DRV2605 Manual de usuario

Texas Instruments

Texas Instruments THS3062EVM Manual de usuario

Texas Instruments

Texas Instruments BQ77207 Manual de usuario

Texas Instruments

Texas Instruments XWRL1432BOOST Manual de usuario

Texas Instruments

Texas Instruments TA 5 42EVM-K Series Manual de usuario

Texas Instruments

Texas Instruments DRV8334 Manual de usuario

Texas Instruments

Texas Instruments AFE20408EVM Manual de usuario

Texas Instruments

Texas Instruments DCA1000EVM Manual de usuario

Texas Instruments

Texas Instruments TPS65735EVM-703 Manual de usuario

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario

Texas Instruments bq51013AEVM-765 Manual de usuario

Manuales populares de Placa madre de otras marcas