Texas Instruments TPS23525EVM-815 Manual de usuario
1
SLVUB36–October 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
User's Guide
SLVUB36–October 2017
TPS23525EVM-815 Evaluation Module
This user’s guide describes the TPS23525 evaluation module (TPS23525EVM-815). TPS23525EVM-815
contains evaluation and reference circuitry for the TPS23525, which is a low-side hot swap and dual
ORing controller targeted at telecom applications.
Contents
1 Introduction ................................................................................................................... 1
1.1 Features.............................................................................................................. 1
1.2 Applications.......................................................................................................... 2
1.3 Electrical Specifications............................................................................................ 2
2 Schematic .................................................................................................................... 3
3 General Configuration and Description .................................................................................. 4
3.1 Physical Access .................................................................................................... 4
3.2 Equipment Setup ................................................................................................... 5
3.3 Scope Considerations ............................................................................................. 5
4 Test Results ................................................................................................................. 5
5 Bill of Material .............................................................................................................. 13
List of Tables
1 TPS23525 Electrical and Performance Specifications at 25°C........................................................ 2
2 Connector Functionality .................................................................................................... 4
3 Test Points.................................................................................................................... 4
4 Jumper Descriptions......................................................................................................... 4
5 TPS23525EVM-815 Bill of Materials..................................................................................... 13
Trademarks
All trademarks are the property of their respective owners.
1 Introduction
The TPS23525 EVM provides a jump-start to anyone designing a redundant feed –48-V system. The EVM
includes input clamping to support lightning surge (up to 2 kV), various FET placeholders to support
various power levels, and an output inductor to mimic any EMI filter before the DC/DC converter.
Additionally, the EVM includes circuitry that supports auxiliary bulk capacitors. This “auxiliary bulk
capacitor” approach is useful when designing for large hold-up times (example: 10 ms) making the hot-
swap design more manageable by reducing the initial charge on the capacitor.
1.1 Features
This EVM has the following features:
• Inrush current control
• Hot-swap output short-circuit protection
• Reverse current protection
• Dual supply ORing
• Reverse hookup protection
Introduction
www.ti.com
2SLVUB36–October 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
1.2 Applications
This EVM is used in the following applications:
• Wireless infrastructure
• Telecom infrastructure
• –48-V interface
1.3 Electrical Specifications
Table 1 lists the TPS23525 electrical and performance specifications at 25°C.
Table 1. TPS23525 Electrical and Performance Specifications at 25°C
Characteristic TPS23525EVM-PWR815
Input voltage Range (Recommended) 38 V to 60 V
Input Voltage Range (Abs Max) 0 V to 150 V
Load Power 400 W
Load Output Cap 660 µF
Current Limit (Normal) 12.5 A
Current Limit (High FET VDS) 1.5 A
Typical Inrush Current 0.4 A
Hot-swap FET VDS when current transitions from high to low 20.2 V
Time Out (VDS,HS < 10 V) 2.25 ms
Time Out (10 V < VDS,HS < 20 V) 1.12 ms
Time Out (VDS,HS > 20 V) 0.23 ms
Undervoltage Threshold (Rising) 36.6 V
Undervoltage Threshold (Falling) 34.6 V
Overvoltage Threshold (Rising) 64.4 V
Overvoltage Threshold (Falling) 61.4 V
General Configuration and Description
www.ti.com
4SLVUB36–October 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
3 General Configuration and Description
3.1 Physical Access
Table 2 lists the TPS23525EVM connector and functionality, Table 3 describes the test point availability,
and Table 4 describes the default jumper configuration.
Table 2. Connector Functionality
Connector Label Description
J1, J2, J3 RTN Power bus input - Tie the high-side of power-supply inputs and outputs here
J7 Neg48V_B Power bus input - Tie the low-side of power-supply B input here
J8 Vout_FLTD Output bus - Apply the low-side load here (if applicable)
J9 CAUX Connect to auxiliary bulk capacitor (if applicable)
J10 Neg48V_A Power bus input - Tie the low-side of power-supply A input here
Table 3. Test Points
Connector Label Description
TP1 RTN High-side power-supply input and high-side output load voltage
TP2 VCC Clamped voltage supply
TP3 PGB Power Good Bar
TP4 SS Soft-start pin voltage
TP5 UVEN UV pin voltage
TP6 D D pin voltage
TP7 OV OV pin voltage
TP8 GATE Gate drive output voltage for hot-swap FET
TP9 SNS Sense pin test point
TP10 TMR Timer capacitor voltage
TP11 GATEB Gate drive output voltage for Gate B ORing FET
TP12 GATEA Gate drive output voltage for Gate A ORing FET
TP13, TP15 VEE IC ground - Place voltage probe ground at this pin
TP14 Neg48VB Low-side input for power-supply B
TP16 HS_DRAIN Drain voltage of the hot-swap FET
TP17 VOUT_FLTD Low-side output for load
TP18 Neg48VA Low-side input for power-supply A
TP19 - Open-drain output for power good signal. Attach to downstream EN pin.
Table 4. Jumper Descriptions
Connector Description
J5 Jump pins 1-2 to enable UV (default), or jump pins 2-3 to tie UV to VCC (disable)
J6 Leave open to enable OV (default), or jump pins 1-2 to tie OV to GND (disable)
www.ti.com
General Configuration and Description
5
SLVUB36–October 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
3.2 Equipment Setup
Use the following equipment list and setup steps to work with the EVM:
• 2× power supplies capable of ≥60 V and ≥15 A (preferred)
• Resistive or electronic load – only turn on the load after the hot swap is up
• Set the input power-supply voltage to the desired operating input voltage
• Turn the power supply off
• Jump pins 1-2 on J5
• Leave pins 1-2 on J6 open
• Connect the positive voltage lead from the power-supply A to J1 (RTN). Connect the ground lead from
the power-supply A to J10 (Neg48V_A).
• Connect the positive voltage lead from the power-supply B to J3 (RTN). Connect the ground lead from
the power-supply B to J7 (Neg48V_B).
• Make sure all voltmeter or oscilloscope GNDs are tied to VEE
• Turn the power supplies on
3.3 Scope Considerations
Observe the following scope considerations:
• Most scopes have a 10-MΩresistance between scope GND and probe.
• If scope GND is tied to RTN and a probe is placed on TMR, that creates approximately 5 μA of pullup
current which can overpower the pull down of the TMR pin and result in an undesired time out.
4 Test Results
This section provides typical performance waveforms for the TPS23525EVM-815 board. Actual
performance data is affected by measurement techniques and environmental variables; therefore, these
curves are presented for reference and may differ from actual results obtained. All curves are based on
VIN = 48 V, unless stated otherwise.
No Load, Scope GND = –48V_A
Figure 2. Start Up (VIN = 54 V)
No Load, Scope GND = –48V_A
Figure 3. Start Up (VIN = 54 V)
Test Results
www.ti.com
6SLVUB36–October 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
No Load, Scope GND = –48V_A
Figure 4. Start Up (VIN = 38 V)
No Load, Scope GND = –48V_A
Figure 5. Start Up (VIN = 60 V)
VINA = 54 V, VINB = 54 V, No Load, Scope GND = RTN
Figure 6. Hot Plug Channel A and B Together
VINA = 54.5 V, VINB = 54 V, No Load, Scope GND = RTN
Figure 7. Hot Plug Channel A and B Together
VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A
Figure 8. Hot Plug A After B
VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A
Figure 9. Hot Plug A After B
www.ti.com
Test Results
7
SLVUB36–October 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
VINA = 54 V; VINB = 38 V, Scope GND = RTN, Iload = 5 A
Figure 10. Hot Plug A After B
VINA = 54.5 V; VINB = 54 V, Scope GND = RTN, No Load
Figure 11. Hot Plug A After B
Scope GND = –48V_B, No Load, After Inductor
Figure 12. Output Hot Short (VINB = 54 V)
Scope GND = –48V_B, 5-A Load, After Inductor
Figure 13. Output Hot Short (VINB = 54 V)
Scope GND = –48V_B, 5A Load, Zoomed in
Figure 14. Output Hot Short (VINB = 54 V)
Scope GND = –48V_B, 5-A Load
Figure 15. Output Hot Short (VINB = 60 V)
Test Results
www.ti.com
8SLVUB36–October 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
Scope GND = –48V_B, 5-A Load, Zoomed In
Figure 16. Output Hot Short (VINB = 60 V)
Scope GND = –48V_A
Figure 17. Gradual Overcurrent (VINA = 54 V)
Scope GND = –48V_A
Figure 18. Load Step Overcurrent
Scope Gnd = –48V_A, VIN = 54 V
Figure 19. Start Into Short
Scope Gnd = –48V_A, VIN = 54 V
Figure 20. Start Into Short
Scope Gnd = –48V_A, VIN = 54 V
Figure 21. Apply Short and Remove Short
www.ti.com
Test Results
9
SLVUB36–October 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
Scope GND = –48V_A, Iload = 5 A
Figure 22. 1-ms Brown Out
Scope GND = –48V_A, Iload = 5 A
Figure 23. 1-ms Brown Out
VINB = 53 V, Iload = 5 A, Scope GND = RTN
Figure 24. Supply Switch Over (Raise VINA)
VINB = 53 V (Raise VINA), Scope GND = RTN, Iload = 5 A
Figure 25. Supply Switch Over (Zoomed in)
VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN
Figure 26. VINA Short
VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN
Figure 27. VINA Short
Test Results
www.ti.com
10 SLVUB36–October 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
TPS23525EVM-815 Evaluation Module
VINA = 54.5 V; VINB = 54 V, Iload = 5 A, Scope GND = RTN
Figure 28. Unplug VIN A
VINB = 60 V
Figure 29. Plug in VIN A Backwards
VINB Floating
Figure 30. Plug in VIN A Backwards
Scope GND = –48V_A, No Load
Figure 31. Undervoltage and Overvoltage (Rising)
Scope GND = –48V_A, No Load
Figure 32. Undervoltage and Overvoltage (Falling)
Scope GND = RTN, 5-A Load, Per IEC61000-4-5
Figure 33. –2-kV (2 Ω) Lightning Surge
Tabla de contenidos
Otros manuales de Unidad de control de Texas Instruments
Texas Instruments
Texas Instruments ADS8555EVM-PDK Manual de usuario
Texas Instruments
Texas Instruments TMS320 Series Manual de usuario
Texas Instruments
Texas Instruments LM5156EVM-BST Manual de usuario
Texas Instruments
Texas Instruments TAS2559 Manual de usuario
Texas Instruments
Texas Instruments LP8863EVM Manual de usuario
Texas Instruments
Texas Instruments SN65LVDS387EVM Manual de usuario
Texas Instruments
Texas Instruments LP8864 Manual de usuario
Texas Instruments
Texas Instruments TPS2390EVM Manual de usuario
Texas Instruments
Texas Instruments DRV8601 Manual de usuario
Texas Instruments
Texas Instruments DRV2625 Haptics BoosterPack Manual de usuario
Texas Instruments
Texas Instruments CDCE 9 Series Manual de usuario
Texas Instruments
Texas Instruments 2000 series Manual de usuario
Texas Instruments
Texas Instruments TPS254900AQ1EVM-003 Manual de usuario
Texas Instruments
Texas Instruments DAC5674 EVM Manual de usuario
Texas Instruments
Texas Instruments DLP NIRscan EVM Manual de usuario
Texas Instruments
Texas Instruments AFE881H1 Manual de usuario
Texas Instruments
Texas Instruments LM5066I EVM Manual de usuario
Texas Instruments
Texas Instruments ADS5231 EVM Manual de usuario
Texas Instruments
Texas Instruments BOOSTXL-TPS652170 Manual de usuario
Texas Instruments
Texas Instruments AM263P Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
