TESTO 300 Manual

Otros manuales para 300

3

Tabla de contenidos

Otros manuales de Instrumento de medición de TESTO

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

testo 300 - Combustion Analyzer

Short instructions

Register your Testo product at www.testo.com/register and receive a one-year

free warranty extension.

The product registration is valid for 30 days after purchase.

For product registration terms and conditions and participating countries, please

go to www.testo.com/register

Contents

Contents

1About this document ...................................................................................5

2Safety and disposal .....................................................................................5

3Product-specific safety instructions ..........................................................5

4Use ................................................................................................................6

5Product description .....................................................................................7

5.1 Front view...............................................................................................7

5.2 Rear view ...............................................................................................8

5.3 Connections ...........................................................................................8

6Commissioning ............................................................................................9

6.1 Power supply / Battery ...........................................................................9

6.1.1 Charge battery.........................................................................9

6.2 Switch instrument on and off ................................................................10

6.3 Display - user interface.........................................................................11

7Using the product ......................................................................................12

7.1 Overview of main menu ( ).............................................................12

7.2 Overview of measurement types ( ).............................................14

7.3 Overview of options ( ) .................................................................15

7.4 Overview of tests ( ) ......................................................................16

7.5 Get the measurement data in 3 steps ..................................................17

8Technical data ............................................................................................18

8.1 Product-specific approvals ...................................................................19

9Contact and support ..................................................................................19

1 About this document

5

1About this document

•The instruction manual is an integral part of the instrument.

•Keep this documentation to hand so that you can refer to it when necessary.

•Please read this instruction manual through carefully and familiarize yourself

with the product before putting it to use.

•Hand this instruction manual on to any subsequent users of the product.

•Pay attention to the safety instructions and warning advice to prevent injury

and damage to the product.

2Safety and disposal

Take the testo information document into account (accompanies the product).

3Product-specific safety instructions

CAUTION

The condensate may be acidic.

Risk of burns to the hands!

-

Wear acid-resistant safety gloves, glasses and overalls to empty the

condensate.

•Make sure that the condensate has been fully emptied out of the condensate

trap before the measuring instrument is stored for a long time.

•Before disposing of the product, the condensate trap must be emptied and

the condensate in the crude gas tube disposed of in a suitable container.

•When testing a gas pipe, pay attention to the following:

WARNING

Dangerous mixture of gases

Danger of explosion!

-

Make sure there are no leaks between the sampling point and the measuring

instrument.

-

Do not smoke or use naked flames during the measurement.

4Use

6

4Use

The testo 300 is a measuring instrument for flue gas analysis on applications,

such as

•residential, commercial and industrial applications (oil, gas, wood, coal)

•low-temperature and condensing boilers

•boilers, furnaces and gas heaters.

Using the instrument, these systems can be adjusted and checked for

applicable limit values.

The instrument has been verified as a short-term measuring instrument and

should not be used as a safety (alarm) device.

The following tasks can also be performed using the instrument:

•Checking the O2, CO and CO2, NO, NOxvalues in combustion plants to

ensure optimum operation.

•Draft measurement.

•Measuring the gas flow pressure in gas heaters.

•Measuring and optimizing the flow and return temperatures of heating

systems.

•Measuring the CO concentration in the ambient air.

A NOxfilter for the CO sensor can be ordered as a spare part to replace a used

filter.

5 Product description

7

5Product description

5.1 Front view

1

USB interface/

mains connection

4

User interface

2

Gas outlet

5

Condensate container

3

On/Off button

6

Connections

5Product description

8

5.2 Rear view

1

Attachment point for carrying

strap

2

Magnets

5.3 Connections

1

Probe connections for additional

probes

3

Flue gas socket

2

Integrated ambient air probe 4

Differential pressure

measurement connection

There must be no more than one extension lead (0554 1202)

connected between flue gas socket and flue gas probe.

6 Commissioning

9

6Commissioning

6.1 Power supply / Battery

The measuring instrument is supplied with a rechargeable battery.

Fully charge the battery before use.

If plugged in

, the measuring instrument is automatically powered via the

power supply.

Only charge the battery at an ambient temperature of 32 to 95°F.

6.1.1 Charge battery

1

Connect the instrument plug of the power supply to the power supply

socket on the measuring instrument.

2

Connect the power plug of the power supply to an outlet.



The charging process starts. LED in the condensate trap flashes red.



The charging process stops automatically when battery is fully

charged. LED in the condensate trap has a continuous red light.

If the battery has discharged completely, the charging time at room

temperature is approx. 5-6 hrs.

6Commissioning

10

6.2 Switch instrument on and off

Current

status

Action Function

Instrument

off

Press the button for

a long time (> 3 s)

Instrument is turned on.

When the measuring instrument is started for the first time, the setup

wizard guides you through the following setting parameters step by

step:

- Country version (basis of calculations)

- Language

- Wi-Fi

- Date and Time

- Own company address

- E-mail account*

- Product registration

A tutorial can be started after the setup wizard.

The tutorial demonstrates the general operation and the most

important functions of the measuring instrument using examples.

*Note: If you don’t have your Email server information available you

can skip this step.

Instrument

on

Press the button

briefly (< 1 s)

Instrument is turned to standby mode.

The instrument is re-activated when the

button is pressed again.

Instrument

off

Press the button for

a long time (> 1 s)

Selection: [OK] Instrument is turned off

or cancel the instrument being turned off

with [Cancel].

Unsaved readings are lost when the measuring instrument is turned off.