TESA HEXAGON DIALTRONIC EASY Manual de usuario
INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
INSTRUCCIONES DE USO
INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
INSTRUCCIONES DE USO
E
S
D
F
I
DIALTRONIC EASY
2
Installing and replacing the battery
(or Power cable).
Mise en place et remplacement de la
batterie (ou câble Power).
Einbau und Austausch der Batterie
(oder Power Kabel).
Installazione e sostituzione della batteria
(o del cavo Power).
Colocación y sustitución de la batería
(o cable Power).
No. 0 No. 0 (0,4x2,5mm)
Battery / batterie / batterie / batteria / batería: lithium 3V, type CR2032
8 h6
59.8
4
7
25.4
11.8
12
12
M2-depth 3
(6x)
3
Diagram for rear xings
Schéma de xation arrière
Schema für die Befestigung hinten
Schema di ssaggio posteriore
Esquema de jación posterior
1
5
2
4
7
8
3
6
9
12 1212 12
10
14
13
15
11
4
E
5
E
Description
1. MODE button
2. SET button
3. “Favorite” button
4. Clamping Ø 8 or 3/8”
5. Lifting cap
6. Measuring insert Ø 3 / M2.5 or 4-48-UNF
7. Slot for inductive cable
8. Slot for battery or Power Cable
9. Measurement units (mm/INCH)
10. + / - Indicator
11. Low battery
12. Preset mode
13. 6-digit display
14. Hold measured value
15. Send data
6
E1 . Operating features of the instrument
- The «Mode» key gives access to the functions (units, preset and direction of measurement).
- The «Favorite» key gives direct access to the function used most often (see chap. 4).
- Sets a Preset value, veries a selection, and controls switching o the instrument.
It is possible to activate or de-activate certain functions of the instrument via RS232.
- Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits.
2. Start Press a button... then measure.
SET
7
E
3. Basic functions
Each short press on gives direct access to the basic functions :
.......Inputting a Preset value
next digit 0...9 save PRESET
.......Units selection (mm or Inch)
.......Choice of measurement direction (positive or negative sense)
.......Automatic switch-o mode
= de-activated, = active (after 10 min.)
>2s
8
E4. Favorite key
The «Favorite» key gives direct access to a predened function, and can be congured according to the needs of the
user. In order to assign a function to the «Favorite» key, give a prolonged press on , and then select the required
function:
Validation of selection: By a prolonged press on , or a short press on or
Note: a function can also be assigned via RS232 using the command <FCT + Function No.> (FCT 0...3)
example: Hold display = <FCT1>
Data transmission
(default) Hold display Zero reset
5. Switching o
The dial gauge goes automatically into stand-by if not used for 10 minutes.
Stand-by mode can be forced by a prolonged press (> 2 sec) on :
In stand-by mode, the value of the origin is retained by the sensor, and the instrument automatically restarts with any
movement of the measurement probe, RS command or press a button.
No function
>4s
9
E
The instrument can be switched o completely for a long period of non-use, but this will necessitate a zero reset on restart
(the origin will be lost) :
- Prolonged press (>4 sec) on :
6. Re-initializing the instrument
The initial instrument settings can be restored at any time by a prolonged press (>4 sec) simultaneously on and
until the message is displayed.
Nevertheless the instrument retains its conguration settings (units and resolution).
No function
10
E7. Connecting the instrument
The instrument can be connected to a peripheral via a inductive, Power (Power-USB). See page 2 for connecting the
Power cable.
Measured values can be transmitted and the instrument driven using predened commands (see chap. 8 for a list of the
main commands).
8. List of the main commands
Selection and conguration Interrogation
CHA+ / CHA Change measurement direction CHA? Measurement sense?
FCT0 ...9...A...F Assign «favorite» function FCT? «Favorite» function active?
MM / IN Change measurement unit UNI? Measurement unit active?
PRE [+/-]xxx.xxx Modify preset value PRE? Preset value?
STO1 / STO0 Activate / de-activate HOLD STO? Status of HOLD function?
LCAL dd.mm.yy Modify last calibration date LCAL? Date of last calibration?
NCAL dd.mm.yy Modify next calibration date NCAL? Date of next calibration?
UNI1 / UNI0 Activate / de-activate change of units ?Current value (mode Tol, value followed by <=>)
OUT0 / OUT1 Activate / de-activate contin. data transmission SET? Main instrument parameters?
PRE ON / PRE OFF Activate / de-activate Preset function ID? Instrument identication code?
PRE Recall Preset SN? Instrument serial code?
SET Zero reset Maintenance functions
RES2 / RES3 Change of résolution BAT? Battery status (BAT1 = OK, BAT0 = low battery)
SBY xx Number of minutes before stand-by OFF Switch-o (wake up using a button or RS)
RST Re-initialisation of the instrument
SBY Put instrument in stand-by
VER? Version No. and date of rmware
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Instrumento de medición de TESA
TESA
TESA TESATRONIC TT20 Manual de usuario
TESA
TESA Micro-Hite 10 Guía de configuración
TESA
TESA HEXAGON RUGOSURF 90G Manual de usuario
TESA
TESA CLINOBEVEL 3 Manual de usuario
TESA
TESA TESA-hite Magna 400 Manual de usuario
TESA
TESA TESA-hite plus M 400 Manual de usuario
TESA
TESA TWIN-SURF Manual de usuario
TESA
TESA MICRO-HITE Manual de usuario
TESA
TESA MH3D Manual de usuario
TESA
TESA CLINOBEVEL 2 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario