Tenda G1005D Manual de usuario

is the registered trademark of Shenzhen

Tenda Technology Co., Ltd. All the products and product names

mentioned herein are the trademarks or registered trademarks

of their respective holders. Copyright of the whole product as

integration, including its accessories and software, belongs to

Shenzhen Tenda Technology Co., Ltd. Without the permission of

Shenzhen Tenda Technology Co., Ltd, any individual or party is

not allowed to copy, plagiarize, imitate or translate it into other

languages.

All the photos and product specifications mentioned in this guide

are for references only. As the upgrade of software and

hardware, there will be changes. And if there are changes,

Tenda is not responsible for informing in advance. If you want to

know more about our product information, please visit our

website at www.tenda.cn.

Content

1. Introduction ------------------------------------------------1

1.1 Switch Features --------------------------------------------1

1.2 Package Contents -----------------------------------------2

1.3 Front Panel and Side Panel Specifications --------------2

1.4 LED Indicator Specifications------------------------------3

2. Installation -------------------------------------------------5

2.1 Before Connecting to the Network ----------------------5

2.2 Connecting to End Nodes--------------------------------5

2.3 Switch to Router or Switch --------------------------------6

3. Product Specification --------------------------------------7

1. Introduction

The G1005D/G1008D 5/8-Port Desktop Gigabit Ethernet Switch,

mini and exquisite, is especially suitable for small-sized

networking. It provides 5/8 10/100/1000Mbps Auto-negotiation

ports and supports Auto MDI/MDIX. These Gigabit ports can be

used not only as ordinary ports, but as Uplink ports connected to

other networking devices. You can replace the 10/100Mbps

switch with the G1005D/G1008D to resolve the bottleneck

issues of server terminal connectivity, because the speed at each

port can be up to 2000Mbps in full-duplex mode. It’s the best

choice for you to upgrade from the normal 10/100Mbps to

1000Mbps. Moreover, its easy setup and no network

management will benefit you a lot. So you can select this Gigabit

Switch as a prime switch to improve the speed between different

departments and servers.

1.1 Switch Features

Complies with IEEE802.3, IEEE802.3u and

IEEE802.3ab Ethernet standards

Supports Auto MDI/MDIX on each port

Supports NWAY Auto-Negotiation function

Provides 5/8 10/100/1000Mbps Auto-Negotiation

RJ-45 ports

Supports IEEE802.3x flow control for full-duplex and

Backpressure flow control for half-duplex

Provides up to 10/16Gbps backplane bandwidth and

non-blocking line speed forwarding

Supports store-and-forward switching method

Provides MAC address self-learning/auto-aging and

8K MAC address entries

Desktop and mini plastic shell design

1.2 Package Contents

Please check the articles carefully after you open the packing as

below:

One 5/8-Port Desktop Gigabit Ethernet Switch

One Power Adapter

One User Guide

One Warranty Card

If any of the listed items are missing or damaged, please contact

the reseller from whom you purchased for replacement.

1.3 Front Panel and Rear Panel Specifications

The front panel of 5/8-Port Desktop Gigabit Ethernet Switch

includes 5/8 Link/Act indicators and one power indicator. Please

refer to the detailed description of these indicators in LED

Indicator Specifications.

The front panel of the Switch

The Rear Panel of the Switch includes 5/8 10/100/1000Mbps

RJ-45 ports and one AC power port used for AC power input.

The rear panel of the Switch

Notice: Please use the delivery-attached power adapter. If

not, the switch may be damaged.

1.4 LED Indicator Specifications

The LED indicators of the Switch include Power and 5/8 Link/Act

indicators. You can see their operating situation through these

LED indicators.

The following chart shows the LED indicators of the Switch along

with explanation of each indicator.

LED

Color Status Description

Green ON

This indicator lights

when the Switch turns

on.

Power

— OFF

If this indicator is not

lighting, please check

the AC power connector

to ensure proper

connectivity of the

power cable and the

Switch.

Indicates the Switch is

connected on

1000Mbps.

Green

Blinking

Indicates the Switch is

transmitting/receiving

data packets at

1000Mbps.

Indicates the Switch is

connected on

10/100Mbps.

Red

Blinking

Indicates the Switch is

transmitting/receiving

data packets at

10/100Mbps.

Link/Act

—OFF Indicates the connection

fails.

2. Installation

2.1 Before Connecting to the Network

Before connecting the G1005D/G1008D to the network, please

pay attention to the following instructions:

¾Don’t put heavy articles on the Switch.

¾Power sockets and equipments should be within 1.5 meters

of the Switch.

¾Check power adapter to confirm the safe connection.

¾Make sure there’s adequate space for proper heat

dissipation and adequate ventilation around the Switch.

2.2 Connecting to End Nodes

Use standard Ethernet cable to connect the Switch to end nodes

as described below. Switch ports will automatically adjust to the

characteristics (MDI/MDIX, speed, duplex) of the device to which

is connected.

Switch connecting to an end node

Please refer to the LED Indicator Specifications. The Link/Act

LEDs for each port are turned on when the link is available.

2.3 Switch to Router or Switch

Connecting to another router or switch

Please refer to the LED Indicator Specifications. The Link/Act

LEDs for each port are turned on when the link is available.

3. Product Specification

Standards

IEEE802.3 10Base-T Ethernet

IEEE802.3u 100 Base-TX Fast

Ethernet

IEEE802.3ab Gigabit Ethernet

Protocol CSMA/CD

Topol o gy Sta r

Network Cables

10 Base-T: Cat.3 UTP or above

100 Base-TX: Cat.5 UTP /STP

1000Base-T: Cat.5, Cat.5e or

Cat.6 UTP/STP

Speed 10/100/1000Mbps

Transmission Method store-and-forward

MAC Address Table 8K entries

14880pps(10Mbps)per port

148800pps(100Mbps)

per port

Packet Filtering/

Forwarding Rate 1488000pps(1000Mbps)

per port

MAC Address Learning

Self-learning, auto-aging

Power External universal power supply

AC Input AC 9V 1200mA

Power Consumption 6W/7.2W

Operating Temperature

0OC ~40OC

Storage Temperature -40OC ~70OC

Operating Humidity 10%~90% RH no condensing

Storage Humidity 5%~90% RH no condensing

Otros manuales para G1005D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Tenda

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad