TELEJET Matrix 570VT Guía del usuario
MATRIX® 570VT
SETUP MANUAL
Software version 1.00
COPYRIGHTS
© 2011 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described
in it may be reproduced, copied, photocopied, translated, or reduced in any form or by any means, electronic or
machine readable, recording or otherwise, without prior written consent from TeeJet Technologies.
TRADEMARKS
Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their
respective companies or organizations.
LIMITATION OF LIABILITY
TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED. NO COPYRIGHT LIABILITY OR PATENT IS ASSUMED. IN NO EVENT SHALL
TEEJET TECHNOLOGIES BE LIABLE FOR ANY LOSS OF BUSINESS, LOSS OF PROFIT, LOSS OF USE OR
DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS BEEN ADVISED OF SUCH DAMAGES
ARISING FROM TEEJET TECHNOLOGIES SOFTWARE.
To ensure optimal use of the equipment, please read this manual thoroughly. Please contact TeeJet Technologies
Customer Support or an authorized TeeJet Technologies dealer if additional support is required.
1
98-05266 R0 US
Matrix® 570VT ● ISOBUS
Table of Contents
CHAPTER 1– PRODUCT OVERVIEW 2
OPTIONAL SYSTEM COMPONENTS 3
CONFIGURATIONS 5
POWER ON/OFF 7
Start Up Sequence .........................................................................................................................................7
GENERAL OPERATION INFORMATION 8
CHAPTER 2 – SYSTEM SETUP 9
CULTURE 10
Units...........................................................................................................................................................10
Language .................................................................................................................................................11
Time Zone ................................................................................................................................................11
CONSOLE 12
Volume ......................................................................................................................................................12
LCD Brightness .......................................................................................................................................13
Virtual Terminal Number.....................................................................................................................13
Touch Screen Calibration....................................................................................................................14
About/Save..............................................................................................................................................15
Save About Information ............................................................................................................. 15
APPENDIX A - TIME ZONES 16
APPENDIX B - UNIT SPECIFICATIONS 17
2www.teejet.com
Matrix® 570VT ● ISOBUS
CHAPTER 1– PRODUCT OVERVIEW
The Matrix 570VT is designed to provide years of service under typical agricultural operating conditions. A tight
tting enclosure, combined with rubber covers for all connectors mean that typical dusty environments will not
cause operational problems. While occasional splashing of water will not damage the unit, the Matrix 570VT is not
designed for direct exposure to rain. Take care not to operate the Matrix in wet conditions.
Figure 1-1: Console Front & Back
Power Button
Power Button
USB Port with Rubber Cover
USB Port with Rubber Cover
Standard RAM Bracket
Bright Touch Screen
Rubber Connector
Covers
Integrated RAM Mount
Speaker
Recessed Connectors
Connection ports are not usedPower Connection
3
98-05266 R0 US
Matrix® 570VT ● ISOBUS
OPTIONAL SYSTEM COMPONENTS
IC18 Sprayer/NH3 ECU
Use with your existing VT or Matrix® 570VT
• Works seamlessly and displays on any ISOBUS
VT
• Easy navigation menu and data rich display
• IC18 Sprayer ECU suitable for use with NH3
and liquid fertilizer
• Automatic boom section control upgrade option
• Variable rate control available providing your VT
has GPS and task control capability
• Add additional ISOBUS ECUs as your needs
change
• Provides basic rate control
• Standardized plugs, cables and software
simplify installation and connectivity and result
in true “plug and play” technology. IC18 ECU
resides on the implement, reducing hardware in
the cab
Figure 1-2: IC18 Job Computer
IC18 Spreader
Electronic Control Unit
Use with your existing VT or the Matrix 570VT for dry
product application
• Works seamlessly and displays on any ISOBUS
VT
• Easy navigation menu and data rich display
• Add additional ISOBUS ECUs as your needs
change
• Provides basic rate control
• Standardized plugs, cables and software simplify
installation and connectivity and result in true
“plug and play” technology. IC18 ECU resides on
the implement, reducing hardware in the cab
Figure 1-3: IC18 Spreader Electronic Control Unit
4www.teejet.com
Matrix® 570VT ● ISOBUS
BoomPilot
Electronic Control Unit for IC18
BoomPilot (automatic boom section control) is
possible in combination with software built into the
IC18 Sprayer/NH3 Electronic Control Unit (ECU).
The ECU should be combined with the appropriate
cable to interface with your BoomPilot system, spray
controller and/or spraying machine for quick and easy
installation. Electronic Control Units and their related
cables are designed to control as many boom sections
as the spray controller to which they are connect, up to
a maximum of 9 boom sections.
Figure 1-4: BoomPilot Electronic Control Unit
Switchbox
Manual section control with remote master capibility.
The switchboxs are available in two congurations.
►9 sections output or 8 sections and a master output
►6 sections output or 5 sections and a master output
Figure 1-5: Switchboxes
Extended Warranty
TeeJet offers an extended warranty for many guidance
products. Not available in all markets. Contact your
TeeJet dealer for details.
5
98-05266 R0 US
Matrix® 570VT ● ISOBUS
CONFIGURATIONS
The following diagrams are reective of typical Matrix 570VT in combination with the IC18 Job Computer
congurations. Due to the variety of possible congurations, these should be used for reference purposes only.
Figure 1-6: IC18 Sprayer Retro Kit to Matrix 570VT Harnessing with BoomPilot ECU and Optional Switchboxes
BoomPilot ECU
78-08070
GPS Antenna
78-50155
ISOBUS ABSC
45-05776
50-05177
Dust Cap
6 Boom Switchbox
78-30011
9 Boom Switchbox
78-30012
Matrix
Matrix 570VT
to Incab
Module
45-05824
Matrix 570 VT
75-05024
ISOBUS Incab Module
45-09022
45-09022
XX/XX
CONNECT
TO
BATTERY
CONNECT
TO
BATTERY
ISOBUS Hitch to IC18 Harness
45-09026
IC18 to Raven Sensors Harness
45-10122
to Raven flow control
harness-16 position
5V Regulator for 5V Raven Flow Meter Power
SPEED
Included in Raven 440-460 Retro KitIncluded in TeeJet Retro Kit
IC18 to TeeJet Sensors Harness
45-10121
to TeeJet 8xx series
flow control harness
IC18 ECU Sprayer/NH3
78-08069
6www.teejet.com
Matrix® 570VT ● ISOBUS
Figure 1-7: IC18 Sprayer TeeJet Retro Kit to Matrix 570 VT Harnessing. With optional Rate Controller and Matrix
570G for section control and Mapping capabilities
Rate Controller
Matrix Pro 570G
Matrix Pro 840G
Switchbox
to 570G CAN
45-05823
Capped 4 position DT for
ISOBUS connections
Matrix
Matrix 570VT
to Incab
Module
45-05824
Matrix 570 VT
75-05024
ISOBUS Incab Module
45-09022
45-09022
XX/XX
CONNECT
TO
BATTERY
CONNECT
TO
BATTERY
IC18 to Raven Sensors Harness
45-10122
to Raven flow control
harness-16 position
5V Regulator for 5V Raven Flow Meter Power
SPEED
Included in Raven 440-460 Retro KitIncluded in TeeJet Retro Kit
IC18 to TeeJet Sensors Harness
45-10121
to TeeJet 8xx series
flow control harness
ISOBUS Hitch to IC18 Harness
45-09026
IC18 ECU Sprayer/NH3
78-08069
7
98-05266 R0 US
Matrix® 570VT ● ISOBUS
POWER ON/OFF
Press the POWER BUTTON to power on the console. Upon power up, the Matrix VT will begin its Start Up
Sequence.
Press and briey hold the POWER BUTTON (until the screen turns black) to power off the console.
Figure 1-8: Power Button
Power Button
USB Port with Rubber Cover
Start Up Sequence
The console takes approximately 40 seconds to power up. During this time the TeeJet Technologies logo will be
displayed (brightness levels will uctuate).
Figure 1-9: Master Screen
Matrix VT Setup Key
IC18 NH3
IC18 Crop Sprayer
BoomPilot
Master Screen Key
Options [as available] on the ISOBUS system
will ll in empty squares.
8www.teejet.com
Matrix® 570VT ● ISOBUS
GENERAL OPERATION INFORMATION
A rm touch is required when selecting a screen icon.
For rapid adjustment of a setting, press and hold the UP/DOWN ARROW ICONS
All changes are saved automatically.
The console needs to be cycled off and back on when changing or attaching equipment to the Matrix system.
Press the icon of any menu item to display a denition of that item. To remove the information box, press
anywhere on the screen.
Figure 1-10: Example of Information Text Box
Cleaning suggestions – Matrix consoles should be cleaned with mild cleaners, such as glass cleaner, and a soft
cloth. Take care not to rub dust or other abrasive materials into the touch screen surface.
• Use a soft lint-free cloth.
• The cloth may be used dry, or lightly dampened with a mild cleaner or Ethanol.
• Be sure the cloth is only lightly dampened, not wet. Never apply cleaner directly to touch panel surface; if
cleaner is spilled onto touch panel, soak it up immediately with absorbent cloth.
• Cleaner must be neither acid nor alkali (neutral pH).
• Wipe the surface gently; if there is a directional surface texture, wipe in the same direction as the texture.
• Never use acidic or alkaline cleaners, or organic chemicals such as: paint thinner, acetone, tolulene,
xylene, propyl or isopropyl alchohol, or kerosene.
• Suitable cleaning products are commercially available pre-packaged for use; one example of such a
product is Klear Screen™, or commercially available off-the-shelf retail brands such as Glass Plus® Glass
and Surface Cleaner made by Reckitt-Benckiser.
• Use of incorrect cleaners can result in optical impairment of touch panel and/or damage to functionality.
Tabla de contenidos
