TeleEye CY-S450 Manual de usuario
Cyber Tele
Eye Web Video Solution
Video Server
(CY-S450)
User Guide
Notice:
Signal Communications Limited reserves the right to make improvements to the
product described in this manual at any time and without notice.
This manual is copyrighted. All rights are reserved. This manual may not be copied,
reproduced or translated in whole or part without prior consent from Signal
Communications Limited.
Tele
Eye is a trademark of Signal Communications Limited and is registered in
China, Hong Kong, US and other countries.
All other trademarks are the property of their respective owners.
Copyright © 2002 Signal Communications Limited (A member of
Tele
Eye
Group). All rights reserved.
Version 1.0
Limits of Liability and Disclaimer of Warranty
Signal Communications Limited have taken care in preparation of this manual,
but made no expressed or implied warranty of any kind and assumed no responsibility
for errors or omissions. No liability is assumed for incidental or consequential damages
in connection with or arising out of the use of the information or accessories contained
herein.
Features and specifications are subject to change without prior notice.
Table of Contents
SECTION1
INTRODUCTION 1
!About the Cyber TeleEye Web Video Solution – Video Server 1
SECTION2
INSTALLATION
!What You Have 2
!System Requirement 2
!Software Installation 2
SECTION3
START SERVER 4
!Before you start 4
!Connecting to the Video Server 4
!Auto Redial 6
!Stopping the Server 8
!Exit the Server 8
SECTION4
SERVER ADMINISTRATION 9
!Server Status Page 9
!User Status Page 10
!Configuration Page 11
!History Page 12
!About Page 13
Video Server Software User Guide PAGE 1
Introduction
1
INTRODUCTION
Cyber Tele
Eye Web Video Solution – Video Server is specially
designed for TCP/IP remote video monitoring system so as to achieve real-
time transmission. It serves as an intermediate software between
Tele
Eye
transmitters and
Tele
Eye reception software so as to allow multiple users to
monitor their sites simultaneously.
Cyber Tele
Eye Web Video Solution – Video Server uses adaptation
technique to automatically manage users with different channel conditions. For
user with dialup Internet access, broadband Internet access or LAN, the server
will assign an optimized video stream to that particular user. Individual Internet
video access will not affect the video speed of others. The
Cyber Tele
Eye
Web Video Solution – Video Server configuration is illustrated in the
following block diagram.
Video Server TeleEye Video Transmitter
Pocket PC with M101
Laptop computer with Microsoft IE
Desktop PC with TeleEye Reception software
TCP/IPTCP/IP
SECTION
Video Server Software User Guide PAGE 2
Installation
2
INSTALLATION
Cyber TeleEye Web Video Solution – Video Server runs on Pentium, and
compatible PC with Microsoft Windows NT, Windows 2000 or Windows XP
environment.
What You Have
Your Cyber TeleEye Web Video Solution – Video Server software package
contains:
Software : Video Server CD-ROM
Documentation : User Guide
System Requirements
Component Requirement
Processor Intel Pentium III 800 MHz or better
Memory 256 megabytes (MB) of random access memory
(RAM) or better
Network Interface
Card (NIC) Ethernet card, TCP/IP
Disk space required 20 MB or above
Software Microsoft Windows NT, 2000 , XP
Hardware TeleEye Video Transmitter (TeleEye III+, TeleEye
III+ VRT)
Software Installation
Cyber TeleEye Web Video Solution – Video Server is an auto-run
program. You only have to insert the CD to your CD-ROM, then follow the
SECTION
Video Server Software User Guide PAGE 3
Installation
simple procedures, and you can have your software installed.
Procedures:
1. Insert the software CD-ROM into a CD-ROM drive. The CD-ROM
will run setup automatically.
2. Click Install Cyber TeleEye Web Video Solution – Video
Server to install the software
3. Enter the software serial number which is printed on your CD ROM.
4. Follow the on-screen instruction to install the program.
5. Reboot your computer.
Video Server Software User Guide PAGE 4
Start Server
3
START SERVER
Before You Start
Cyber TeleEye Web Video Solution – Video Server support TCP/IP
(Internet or Intranet) connection only. Before start the server, you should:
!Make sure your network card work properly.
!Make sure you have configured the TCP/IP settings.
!Make sure you have connected to the network properly.
Starting Video Server
Having installed the Video Server successfully, the software will
automatically create a shortcut on your desktop. Double click the shortcut, or
click [Start]->[Programs]->[ Cyber TeleEye Web Video Solution]-
>[Video Server]->Video Server to launch the server. If it is your first time
running the server, the Software Registration Page will pop up.
SECTION
Video Server Software User Guide PAGE 5
Start Server
You can go to the web site http://www.TeleEye.com to do software registration
with the Software Serial Number and Authorization Code provided in this page.
After successful registration, you will obtain a Registration Code. Enter this
code and press the [OK] button, your software will be registered. Afterwards,
the Server Status Page will be shown.
Note: If you have already installed and registered one copy of the Video
Server software, and you want to migrate the software to another computer,
you need to do the un-registratio. Having un-install the software, you will
obtain an un-registration code. Use this code together with the Software Serial
Number and the New Authorization Code to do the registration again for the
software installed on the new computer.
During the first time you start up your Video Server, the server will show you
the default configurations. Otherwise, it will show you the previous
configurations. Enter the Administration password to gain access to the server
and go to the Configuration page. The default Administration password is
“000000”.
Video Server Software User Guide PAGE 6
Start Server
On the left side of the page, select one of the four sites to configure. Enter the
IP address, port number and password of your
Tele
Eye transmitter, enter a
particular server port number, and click [Start]. You server should start
successfully with status shown “Connected”.
Connecting to the Video Server
You can use both
Tele
Eye WRS3-AD software or Microsoft Internet Explorer
to connect to the Video Server to perform live video monitoring. Start you
Tele
Eye WRS3-AD software and click connect with IP address and port
number of the Video Server.
Click here to enter the
Administration
password
Video Server Software User Guide PAGE 7
Start Server
For using Microsoft Internet Explorer, enter the IP address to load the login
page and enter the password to view the remote video.
Tabla de contenidos
Otros manuales de Servidor de TeleEye
