Teledyne Foxy 200 Manual de usuario

Clarity Controls

Teledyne Foxy 200

FC ENG

Code/Rev.: M165/70B

Date: 12/21/2016

Phone: +420 251 013 400 DataApex Ltd.

Fax: +420 251 013 401 Petrzilkova 2583/13

clarity@dataapex.com 158 00 Prague 5

www.dataapex.com The Czech Republic

Clarity ®, DataApex ®and ®are trademarks of DataApex Ltd. Microsoft ®and Windows TM are

trademarks of Microsoft Corporation.

DataApex reserves the right to make changes to manuals without prior notice. Updated manuals can be

downloaded from www.dataapex.com.

Author: DM

Teledyne Foxy 200 Table of Contents

Contents

1 Teledyne Foxy 200 Control Module 1

2 Requirements 2

3 Installation Procedure 3

3.1 Teledyne Foxy 200 fraction collector communication 3

3.2 Clarity Configuration 4

4 Using the control module 6

4.1 Method Setup - FC - Fraction Table 7

4.2 Method Setup - FC - Vial Numbers 12

4.3 Hardware Configuration 14

4.4 Device Monitor 15

4.5 Data Acquisition window 17

4.6 DataApex UNI Setup 18

5 Report Setup 20

6 Troubleshooting 21

- i -

Table of Contents Clarity Controls

To facilitate the orientation in the Teledyne Foxy 200 manual and Clarity chromatography

station, different fonts are used throughout the manual. Meanings of these fonts are:

Instrument (blue text) marks the name of the window to which the text refers.

Open File (italics) describes the commands and names of fields in Clarity, parameters that can

be entered into them or a window or dialog name (when you already are in the topic describing

the window).

WORK1 (capitals) indicates the name of the file and/or directory.

ACTIVE (capital italics) marks the state of the station or its part.

The bold text is sometimes also used for important parts of the text and the name of the Clarity

station. Moreover, some sections are written in format other than normal text. These sections are

formatted as follows:

Note: Notifies the reader of relevant information.

Caution: Warns the user of possibly dangerous or very important

information.

▌ Marks the problem statement or trouble question.

Description: Presents more detailed information on the problem, describes its causes,

etc.

Solution: Marks the response to the question, presents a procedure how to remove it.

- ii -

Teledyne Foxy 200 1 Teledyne Foxy 200 Control Module

1 Teledyne Foxy 200 Control Module

This manual describes the setting of the Teledyne Foxy 200 fraction

collector. The control module enables direct control of the instrument over

serial line.

Fig 1: Teledyne Foxy 200 fraction collector

Direct control means that the fraction collector can be completely

controlled from the Clarity environment. The Instrument method

controlling the analysis conditions will be saved in the measured

chromatograms.

The control is performed via the UNI Ruby control module and the

Teledyne Foxy 200 script.

- 1 -

Teledyne Foxy 200 2 Requirements

2 Requirements

lFree serial COM port in the PC.

Note: Modern computers usually have only one (if any) serial (COM) port

installed. To use more devices requiring the RS232 port, the MultiCOM

adapter (p/n MC01) is available.

lSerial DB9F-DB25M cable (p/n SK12).

Note: Cables are not part of Clarity Control Module. It is strongly

recommended that you order the required cables together with the

Control Module.

- 2 -

Teledyne Foxy 200 3 Installation Procedure

3 Installation Procedure

3.1 Teledyne Foxy 200 fraction collector communication

The Teledyne Foxy 200 is controlled by serial (RS232) communication.

It uses a serial DB9F-DB25M straight cable (p/n SK12) described in the

picture below.

Fig 2: Serial DB9F-DB25M cable

On top of that, the fraction collector must be switched to the same Baud

Rate as set in Clarity and the ID=5 to work with the control module. To do

so, start the fraction collector and load the Program A, then select the Edit

Aoption. Select page 3 from the Edit submenu and set the Serial function,

then set the Baud Rate as desired and ID to 5in the next screen.

- 3 -

3 Installation Procedure Clarity Controls

3.2 Clarity Configuration

Fig 3: How to Add UNI Ruby module

lStart the Clarity station by clicking on the icon on the desktop.

lInvoke the System Configuration dialog accessible from the Clarity

window using the System - Configuration... command.

lPress the Add button (①on Fig 3 on pg 4.) to invoke the Available Control

Modules dialog.

lYou can specify the search filter ②to simplify the finding of the driver.

- 4 -

Teledyne Foxy 200 3 Installation Procedure

lSelect the correct item and press the Add (③on Fig 3 on pg 4.) button.

Each device with already created UNI profile should have its own item

named accordingly in the Available Control Modules dialog.

lThe DataApex UNI Setup dialog will appear.

Fig 4: DataApex UNI Setup

lSet the correct communication Port and click on the AutoDetect button to

establish communication with the device.

lYou may fill in the custom Device Name.

Note: The DataApex UNI Setup dialog is described in detail in the chapter

"DataApex UNI Setup" on pg 18.

lThe Teledyne Foxy 200 item ④will appear in the Setup Control Modules

list of the System Configuration dialog.

lDrag the appropriate item from the Setup Control Modules list on the left

side to the desired Instrument tab ⑤on the right side ⑥, or click on the

button ⑦.

lSet the Ext. Start Dig. Input and Ready Dig. Output numbers ⑧for your

acquisition card according to the wires used for synchronization.

- 5 -

Teledyne Foxy 200 4 Using the control module

4 Using the control module

After adding and setting up the new device one or more new tabs will

appear in the Method Setup dialog depending on the type of the

instrument. A new Teledyne Foxy 200 fraction collector section enabling

the monitoring of the current fraction collector state will be also created in

the Device Monitor window.

- 6 -

Tabla de contenidos

Otros manuales de Unidad de control de Teledyne

Teledyne

Teledyne 5800 Manual de uso y cuidado

Teledyne

Teledyne 2105 Instrucciones de funcionamiento

Teledyne

Teledyne 2105 Instrucciones de funcionamiento

Teledyne

Teledyne 2108 Instrucciones de funcionamiento

Teledyne

Teledyne FLIR Lepton 3.1R Manual de usuario

Teledyne

Teledyne CombiFlash Torrent Manual de usuario

Teledyne

Teledyne 2103Ci Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario