Teleco MAGIC SAT EASY Instrucciones de montaje
Vers. 003
INSTALLATION GUIDE and USER MANUAL
of the
MAGIC SAT EASY
GB
Information
Magic Sat Easy Vers. 003
2
TABLE OF CONTENTS Page
Information.......................................................................................................... 2
List of accessories.............................................................................................. 3
Important notice.................................................................................................. 4
Assembly instructions......................................................................................... 5
Installation with cables through the centre of the base plate........................... 7
Installation with cables coming out sideways.................................................. 9
Connections.................................................................................................. 10
Important information for proper antenna tracking............................................ 13
Tips on the best use of Magic Sat Easy ........................................................... 14
Tips on the best use of Magic Sat Easy ........................................................... 14
Installation tips.................................................................................................. 14
Magic Sat Easy –rear view.............................................................................. 15
Magic Sat Easy –control board........................................................................ 15
Operation of Magic Sat Easy............................................................................ 16
Turning on the Magic Sat Easy..................................................................... 16
Selecting the satellite.................................................................................... 16
Seeking the satellite...................................................................................... 17
Parking the antenna...................................................................................... 17
Turning off the Magic Sat Easy..................................................................... 17
Error code display......................................................................................... 17
Troubleshooting................................................................................................ 18
Technical specifications.................................................................................... 18
Information
Congratulations on your purchase! Magic Sat Easy is among the most technologically
advanced products in the field of satellite TV reception. This handbook has been prepared
to provide information on how to install, use, maintain and technical specifications your
Magic Sat Easy system.
For additional information, please contact your local dealer or directly the manufacturers:
TELECO s.p.a.
Via E. Majorana 49
I-48022 LUGO (RA)
Web site: www.telecogroup.com
Technical attendance: lab@telecogroup.com
Technical attendance: 899.899.856
TELECO s.p.a. declines all responsibility for any errors contained in this manual. All the
contained information are up to the dates of printing and of the above-mentioned software
revisions. TELECO s.p.a. reserves the right to introduce any modification made necessary
by the development of its products.
List of accessories
Vers. 003 Magic Sat Easy
3
List of accessories
Magic Sat Easy is delivered inside a cardboard case that has been specially made to
protect it from knocks and pressure. The following accessories are supplied:
1External motor-driven unit
250 - 65 - 85 cm dish
3Universal LNB
4Control unit
5Wall-mounted control panel
6Motor Connection Cable
7Antenna-Control unit connection lead
8Power Supply Cable
9Control unit/Wall panel connection cable
10 Waterproof box to pass leads through to interior
11 Heat-shrinking sheaths
12 Roof attachment plate
13 No. 4 stainless steel Locknuts M6
14 No. 4 stainless steel Screws and Locknuts - M5 Ø 50 cm / M 6 Ø 65-85 cm
15 User’s manual
Important notice
Magic Sat Easy Vers. 003
4
Important notice
Magic Sat Easy is packaged in two separate cartons for transport reasons:
a) the first package contains the driving unit with all the cables, and the control box.
b) the second package only contains the dish.
• It is important to check that the dish has not been damaged during transport when the
package is opened. In particular, check the following well:
• By resting the dish edge against a flat surface (e.g. the floor or a wall) check that it
makes contact to the surface all around. If it is not so, try and make the edge level,
without denting the dish, or call our After-Sales Service.
• After checking that everything is in order, install the dish on the driving unit as follows:
1) Temporarily connect the Control Box to the driving unit through the grey motor
cable.
2) Connect the control board to the Control Box through the RJ45 cable.
3) Power the Control Box using a battery.
4) Press the switch-on button and wait for the dish support mast to rise.
5) Once the desired position has been reached, turn off the Magic Sat Easy via the
same button.
6) Secure the dish to the mast and screw down the four supplied screws.
7) Turn the unit on again and wait for the antenna to close.
8) Disconnect the the Control Box, the battery and install the driving unit on the
vehicle.
YES
NO
Assembly instructions
Vers. 003 Magic Sat Easy
5
Assembly instructions
1) Position the Control Box in an easy accessible, ventilated compartment.
2) Place the control board comando in an easily accessible, visible position.
3) On the roof of the vehicle, choose a free area large enough to allow the antenna to
revolve (Fig. 2)
4) Install the connection cables (Grey and White) until you reach the OUTSIDE UNIT
installation area.
5) Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in.
6) Remembering that the OUTSIDE UNIT must be fastened as shown on figure 3,
remove the BASE PLATE from the outside unit, unscrewing all 4 nuts. Position the
base plate as shown on figure 4, with the short side towards the driving direction of
the vehicle.
Assembly instructions
Magic Sat Easy Vers. 003
6
7) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the
whole surface (e.g. SIKAFLEX).
8) Fasten the BASE PLATE to the roof (short side towards the vehicle driving
direction), now fasten the external powered unit to the four stud bolts of the plate,
using the four nuts supplied with the equipment.
9) Apply a layer of silicone all around the BASE PLATE in order to make it completely
waterproof (Fig. 5)
Assembly instructions
Vers. 003 Magic Sat Easy
7
Installation with cables through the centre of the base plate
10) Connect the Grey and White cables, coming from inside the vehicle (Fig. 6) to the
two cables of the outside unit, waterproofing them using two pieces of HEAT-
SHRINKING TUBE (Fig. 7)
WARNING When performing this operation, do not draw the cables coming from the
centre of the outside unit forcefully, as this might pull them out.
Assembly instructions
Magic Sat Easy Vers. 003
8
11) Install the OUTSIDE UNIT on the base plate, remembering that:
a) The right position is the one shown on (Fig. 9)
b) Apply an abundant layer of silicone on both the base plate and the bottom of
the driving unit (Fig. 10) so as to prevent any infiltration by water. Screw
down the 4 supplied nuts by the screws and tighten properly (Fig. 11)
Assembly instructions
Vers. 003 Magic Sat Easy
9
Installation with cables coming out sideways
12) Fasten the OUTSIDE UNIT on the base plate and lead the two cables through one
of the 4 existing grooves, according to the position as shown on Fig. 12.
WARNING: When performing this operation, do not draw the two cables forcefully, as this
might pull them out.
13) Connect the two cables coming from the centre of the OUTSIDE UNIT to the two
supplied extensions, waterproofing the connectors using the two pieces of heat-
shrinking tube.
14) Accomodate the cables into a protection raceway up to the point where the cables
go into the vehicle, using the suitable supplied fairlead.
15) Seal the fairlead carefully so as to prevent any infiltration by water.
Assembly instructions
Magic Sat Easy Vers. 003
10
Connections
16) Connect the grey cable (motors) to the MOTOR UNIT connector and the white
coaxial cable (antenna) to the LNB connector of the Control Box.
17) Connect the Receiver to the RECEIVER connector (Fig. 16). You can connect any
satellite receiver, either digital or analog.
18) Connect the BLACK cable of the Control Box to the NEGATIVE POLE of the
vehicle 12 Volt Battery, and the RED cable to the POSITIVE POLE + (remember
not to mix the + and - poles up), using 2 cables of a cross section of 2.52(Fig. 15).
19)The GREEN safety cable of the Control Unit must be connected to the consensus
of the vehicle startup console (in many cases such consensus is located on Pin 15
in the main terminal board). In this way, whenever the motor is started, this cable
receives a positive + 12 Vdc voltage, which will automatically lower the antenna and
lock all functions of the Control Unit simultaneously (Fig.15).
Any connection made in points other than as indicated (e.g. on
the alternator) can give rise to equipment malfunction and/or damage resulting in loss of
the warranty.
Tabla de contenidos
Otros manuales de Sistema de televisión por satélite de Teleco
Manuales populares de Sistema de televisión por satélite de otras marcas
DefineSat
DefineSat VM55 Manual de usuario
Dish Network
Dish Network 112182 Manual de usuario
Thrane&Thrane
Thrane&Thrane sailor 60 Manual técnico
KVH Industries
KVH Industries TracVision L2 Manual de usuario
KVH Industries
KVH Industries TracVision TV1 Manual de usuario
JRC
JRC NJT8304 Series Manual de usuario
Bell
Bell EXPRESSVU Manual de usuario
Promax
Promax SATHUNTER Manual de usuario
SatKing
SatKing PRO MAX Manual de usuario
KVH Industries
KVH Industries TracVision M5 Manual de usuario
KVH Industries
KVH Industries TracVision R5SL Manual de usuario
Dish Network
Dish Network Satellite Television Manual de usuario