Teldat Connect-104 Manual de usuario

Teldat Connect-104 Router

Teldat-Dm 493-I

Teldat S.A. Manual

Teldat Connect-104 Router 1

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-

ery, supply or use of this manual.

Manual Teldat S.A.

2Teldat Connect-104 Router

Table of Contents

I ImportantInformation................................ 1

Chapter1 InstallingtheRouter ................................ 2

1.1 Introduction...................................... 2

1.1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Connections...................................... 3

1.2.1 PowerSourceConnection................................ 4

1.2.2 DataConnections.................................... 5

1.2.3 ConfiguringConnections................................. 7

1.3 MeaningoftheLEDs.................................. 9

1.4 RSTPushbutton.................................... 9

1.4.1 Procedure to ignore the current configuration and to establish the default configuration . . . . 10

1.4.2 Procedure to force startup in BOOT mode . . . . . . . . . . . . . . . . . . . . . . . . 11

1.4.3 Procedure to force startup in BIOS mode . . . . . . . . . . . . . . . . . . . . . . . . 13

1.4.4 Accessing the BIOS menu from the console without using the RST button . . . . . . . . . . 14

Chapter2 Appendix..................................... 16

2.1 Troubleshooting................................... 16

2.2 SoftwareUpdating.................................. 16

2.3 Connectors ..................................... 16

2.3.1 LANConnector.................................... 17

2.3.2 DSLConnector.................................... 17

2.3.3 ANTConnectors................................... 17

2.3.4 USBConnector.................................... 17

2.3.5 ConfigurationConnector................................ 18

2.4 TechnicalSpecifications................................ 18

2.5 ComplianceInformation................................ 19

2.5.1 Compliance Information for Teldat CONNECT-104 Routers Relevant to the European Union and Other

Countries Following EU Directive 1999/5/EC (R&TTE Directive) . . . . . . . . . . . . . . 19

2.6 Translated safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Teldat S.A. Table of Contents

Teldat Connect-104 Router i

Table of Contents Teldat S.A.

ii Teldat Connect-104 Router

I Important Information

Note

The manufacturer reserves the right to make changes and improvements in the software and hardware

of this product, modifying the specifications of this manual without prior notice.

The images showing the front and rear panels of the router are for information purposes only. Some

small modification may exist in the actual device.

The equipment is intended to be installed by Service Personnel and only handled by qualified person-

nel. If not, the device may be damaged and malfunction.

This device contains elements that are sensitive to electrostatic surges and shocks. Therefore, it is es-

sential when handling the equipment that an antistatic wriststrap is connected to the device chassis and

that this is placed on an antistatic mat. Furthermore, it is crucial to avoid any kind of contact between

the device components and necklaces, bracelets, rings, ties, etc.

Teldat S.A. Important Information

Teldat Connect-104 Router 1

Chapter 1 Installing the Router

1.1 Introduction

The Teldat Connect-104 is a general purpose router suitable for a wide range of applications (personal, SOHO/SME

and corporate environments). Thanks to its USB interface, where 3G USB modems can be connected, it covers ac-

cess needs using ADSL, ADSL2+ (over PSTN) and 3G access. For LANs (local area networks), the device incorpor-

ates a 4-port Ethernet LAN Switch and an integrated Wireless LAN module.

The Teldat Connect-104 adapts to plenty of IP scenarios, providing simultaneous access to Internet for private LAN

users and/or for corporations through Virtual Private Networks (VPNs), as well as accommodating teleprocessing

networks. The most common applications are as follows:

• ADSL access router.

• ADSL access router with 3G backup.

Fig. 1: ADSL access router

Fig. 2: ADSL access router with 3G backup

This manual shows how to install and connect these routers.

1 Installing the Router Teldat S.A.

2Teldat Connect-104 Router

Fig. 3: Teldat Connect-104 : External aspect

1.1.1 Recycling and the Environment

Please do not, under any circumstances, throw away any Teldat Connect-104 routers with normal domestic waste.

Ask your local town hall for information on how to correctly dispose of them in order to protect the environment

against e-waste. Always respect the current laws regarding waste material. Anyone found violating the environmental

laws will be subject to fines and any additional steps established by law.

All the packing materials, i.e. the cardboard box, plastic and any other packaging, together with the pieces making up

aTeldat Connect-104 , must be recycled complying with the current applicable laws.

The symbol shown below, with a cross over the rubbish container, can be seen on the device. This means that, when

a device reaches the end of its life, it must be taken to the official recycling/disposal centers where it will be disposed

of in an environmentally responsible manner and separately from normal domestic waste.

1.2 Connections

Note

BEFORE CONNECTING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-

FULLY

Workplace Conditions. Main Characteristics

• Excessive cold and heat should be avoided, as should humidity and dust.

• Avoid direct exposure to sunlight and any other heat sources. Do not place the device between papers, magazines

or other items that could hinder natural air circulation.

• Do not place the device near strong electromagnetic fields such as those produced by speakers, motors, etc.

• Avoid knocks and/or strong vibrations during operation, storage and transport.

Teldat S.A. 1 Installing the Router

Teldat Connect-104 Router 3

Warning

The electric current in power cables, telephone lines and communication cables is dangerous. To pre-

vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-

nect the cables following the steps set forth in the following section.

To Connect To Disconnect

Make sure that the device power switch is in the OFF po-

sition.

Turn the power switch OFF.

Check that the power supply is not connected to the

mains or to the device.

Disconnect the power supply from the mains.

Connect all data cables. Disconnect the power supply from the device.

Connect the power supply to the device. Disconnect the data cables.

Connect the power supply to the mains.

Turn the power switch ON.

1.2.1 Power Source Connection

The Teldat Connect-104 is powered with an external AC/DC source.

To avoid electric shocks, residual current circulation and any other unwanted effects that may disrupt communica-

tion, the following is recommended:

Warning

All interconnected communication devices should be plugged to THE SAME GROUNDED POWER

OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).

Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated

supply, or it is independent from the rest (such as lighting, etc.), it is highly recommended that

all data devices should be connected to the same power source. This will avoid operating and

premature aging problems of drivers and other components..

Fig. 4: Connecting the power with an external source

1 Installing the Router Teldat S.A.

4Teldat Connect-104 Router

To connect the power source to the router, follow the steps listed in the previous table: ensure the switch is OFF (0)

and the power supply is NOT connected to the main electricity supply. Locate the 12 VDC connector, which is on

the rear panel of the router, and plug it into the power source.

1.2.2 Data Connections

The Teldat Connect-104 is equipped with the following connectors:

1.2.2.1 4 port Ethernet Switch (connectors LAN1..4)

The Teldat Connect-104 is equipped with a 410/100BaseT switch, with an automatic MDI/MDIX to connect to the

LAN (local area network).

Please pay close attention to the labelling to avoid confusing the switch with other port types.

Fig. 5: LAN switch ports (4)

1.2.2.2 ADSL/ADSL2+ connection over PSTN (DSL connector)

The Teldat Connect-104 incorporates a DSL connector to connect to an ADSL/ASDL2+ network over PSTN. This is

a female RJ11 connector with 4 wires. Only the central pair is used for data transmission/reception.

For connection purposes, use the telephone cable with male RJ11 connectors (provided with the router).

Fig. 6: DSL connector (ADSL and ADSL2+)

The splitter

The Full Rate ADSL (ITU G.dmt or G.922.1) operating mode uses a higher transmission capacity. To use telephones

directly connected to the same line, you need to install a mechanism known as splitter (which separates the band

frequencies for voice telephony from those used by the ADSL connection to transmit data). This prevents interfer-

ences between both the telephone and ADSL services.

A typical installation with a splitter is shown in Figure 7 .

Teldat S.A. 1 Installing the Router

Teldat Connect-104 Router 5

Fig. 7: ADSL installation with a splitter

The microfilters

The G. Lite (ITU G.922.2) operating mode uses reduced transmission power, allowing telephones directly connected

to the same line to be used with the help of a device known as a microfilter. This device ensures that the ADSL sig-

nal does not reach the telephone and undesired signals generated by the telephone do not interfere with the ADSL

signal.

A typical installation with a splitter is shown in Figure 8.

Fig. 8: ADSL installation with microfilter

1 Installing the Router Teldat S.A.

6Teldat Connect-104 Router

Tabla de contenidos

Otros manuales de Enrutador de red de Teldat

Teldat

Teldat RXL14000 Manual de usuario

Teldat

Teldat iM8-Cx Manual de usuario

Teldat

Teldat K Seres Manual de usuario

Teldat

Teldat H1 RAIL Series Manual de usuario

Teldat

Teldat 4Ge Manual de usuario

Teldat

Teldat ATLAS X60 Manual de usuario

Teldat

Teldat REGESTA-PRO-ER Series Manual de usuario

Teldat

Teldat iM8 Manual de usuario

Teldat

Teldat 3ge Manual de usuario

Teldat

Teldat Connect 104KF TLDPM00A1 Manual de usuario

Teldat

Teldat Regesta Lite AU Manual de usuario

Teldat

Teldat M1 Manual de usuario

Teldat

Teldat WWAN Enabler Manual de usuario

Teldat

Teldat Edge Router Atlas-840 Manual de usuario

Teldat

Teldat Atlas 250 Manual de usuario

Teldat

Teldat 5Ge-Rail Manual de usuario

Teldat

Teldat Atlas 250 Manual de usuario

Teldat

Teldat H2 RAIL Manual de usuario

Teldat

Teldat M2 Manual de usuario

Teldat

Teldat 4Ge Manual de usuario

Teldat

Teldat IMBER SMART Manual de usuario

Teldat

Teldat RS300 Series Manual de usuario

Teldat

Teldat ATLAS 60 NW Manual de usuario

Teldat

Teldat Regesta-PRO ER B Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad