Tektronix MTM400A Manual de uso y cuidado

Technical Reference

MTM400A

MPEG Transport Stream Monitor

Specifications and Performance Verification

071-2496-00

This document applies to firmware versions 3.0

and above.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

MTM400A Specifications and Performance Verification i

Table of Contents

General Safety Summary v...................................

Preface vii...................................................

Product Documentation vii...........................................

Specifications

Electrical, Hardware, and Signal Specifications 1--1........................

Power Source Characteristics 1--15.......................................

Environmental Characteristics 1--16......................................

Mechanical (Physical) Characteristics 1--16................................

Certifications and Compliances 1--17.....................................

Performance Verification

Requirements 2--1...................................................

Procedure 2--1......................................................

Table of Contents

ii MTM400A Specifications and Performance Verification

List of Figures

Figure 2--1: MTM400A monitor RUI display 2--3...................

List of Tables

Table i: Product documentation vii.............................

Table 1--1: Remote User Interface (RUI) platform characteristics 1--1.

Table 1--2: TS processor card - system timing clock 1--1.............

Table 1--3: TS processor card - ASI interface 1--2..................

Table 1--4: TS processor card - SMPTE310M interface 1--2..........

Table 1--5: TS processor card - alarm connector 1--3................

Table 1--6: TS processor card - alarms 1--4........................

Table 1--7: TS processor card - LTC connector 1--4.................

Table 1--8: TS processor card - Ethernet RJ-45 connector 1--4........

Table 1--9: QAM Annex A interface card characteristics 1--5.........

Table 1--10: QAM Annex B2 interface card characteristics 1--5.......

Table 1--11: QAM Annex B2 measurements 1--6....................

Table 1--12: QAM Annex C interface card characteristics 1--6........

Table 1--13: 8PSK/QPSK interface card characteristics with

8PSK input 1--7...........................................

Table 1--14: 8PSK/QPSK interface card characteristics with

QPSK input 1--7...........................................

Table 1--15: 8PSK and QPSK measurements 1--8...................

Table 1--16: 8VSB interface card characteristics 1--8................

Table 1--17: 8VSB measurements 1--9............................

Table 1--18: COFDM interface card characteristics 1--10.............

Table1--19:COFDMmeasurements 1--11..........................

Table 1--20: GigE interface card - general characteristics 1--12........

Table 1--21: GigE interface card - Ethernet electrical port 1--12.......

Table 1--22: GigE interface card - Ethernet Optical port 1--13.........

Table 1--23: GigE interface card - ASI input 1--14...................

Table of Contents

MTM400A Specifications and Performance Verification iii

Table 1--24: GigE interface card - ASI output (active loop-through

of ASI/SMPTE input or TS from GigE interface card) 1--14.......

Table 1--25: GigE interface card - SMPTE310M input

(loop-through to ASI output) 1--14............................

Table 1--26: AC power source characteristics 1--15...................

Table 1--27: Transport stream card batteries 1--15...................

Table 1--28: Environmental characteristics 1--16....................

Table 1--29: Mechanical characteristics 1--16.......................

Table 1--30: Certifications and compliances 1--17....................

Table 1--31: Environmental limits and use classification for safety

certification compliance 1--19.................................

Table of Contents

iv MTM400A Specifications and Performance Verification

MTM400A Specifications and Performance Verification v

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

Use Proper Power Cord. Use only the power cord specified for this product and

certified for the country of use.

Ground the Product. This product is grounded through the grounding conductor

of the power cord. To avoid electric shock, the grounding conductor must be

connected to earth ground. Before making connections to the input or output

terminals of the product, ensure that the product is properly grounded.

Ground Equipment Connected to the Product. Ensure that any equipment

connected to this product is grounded and at the same potential.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

The inputs are not rated for connection to mains or Category II, III, or IV

circuits.

Power Disconnect. The power cord disconnects the product from the power

source. Do not block the power cord; it must remain accessible to the user at all

times.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Do Not Operate With Suspected Failures. If you suspect there is damage to this

product, have it inspected by qualified service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Use Proper Fuse. Use only the fuse type and rating specified for this product.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

ToAvoidFireor

Personal Injury

General Safety Summary

vi MTM400A Specifications and Performance Verification

These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

These terms may appear on the product:

HDANGER indicates an injury hazard immediately accessible as you read the

marking.

HWARNING indicates an injury hazard not immediately accessible as you

read the marking.

HCAUTION indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

CAUTION

Refer to Manual

Protective Ground

(Earth) Terminal

Terms in this Manual

Symbols and Terms

on the Product

MTM400A Specifications and Performance Verification vii

Preface

This manual contains the following information about the MTM400A MPEG

Transport Stream Monitor:

HSpecifications lists the electrical, physical, and environmental specifications

of the MTM400A monitor.

HPerformance Verification contains a procedure to verify that the MTM400A

monitor is operating normally.

Product Documentation

Table i lists the product documentation supporting the MTM400A monitor.

Table i: Product documentation

Item (Tektronix part number) Purpose Location

Quick Start User Manual

(071-2492-xx English,

071-2493-xx Japanese)

Provides installation and high-level

operational overviews ++

RUI v3.0 Upgrade Technical

Reference

(071-2505-xx)

Describes the remote user interface (RUI)

changes introduced with the MTM400A

monitor

Release Notes

(071-2494-xx)

Describes late breaking product informa-

tion and operational issues ++

Technical Reference

(071-2495-xx)

Provides in-depth operating information

(this manual) +

Specifications and Performance

Verification Technical Reference

(071-2496-xx)

Provides complete product specifications

and a procedure for verifying the operation

of the instrument

Test Parameter and Configuration

File Technical Reference

(071-2497-xx)

Provides information about using test

parameters and configuration files

Programmer Manual

(071-2498-xx)

Provides information about remote

command syntax

Declassification and Security Instruc-

tions

(071-2499-xx)

Provides instructions for removing your

proprietary information from the instrument

Preface

viii MTM400A Specifications and Performance Verification

Table i: Product documentation (Cont.)

Item (Tektronix part number) LocationPurpose

Firmware Upgrade Instructions

(075-0972-xx)

Provides instructions for upgrading the

product firmware +

Hardware Upgrade Instructions

(075-0973-xx)

Provides instructions for installing the

optional hardware interface cards

Key:

Printed document

MTM400A product documentation CD - PDF format

Tektronix Web site - PDF format

Otros manuales para MTM400A

Tabla de contenidos

Otros manuales de Monitor de Tektronix

Tektronix

Tektronix WFM6100 Opt. MB Manual

Tektronix

Tektronix MTM400 Manual de uso y cuidado

Tektronix

Tektronix 013-0278-XX Manual de usuario

Tektronix

Tektronix WFM6100 Opt. MB Manual de uso y cuidado

Tektronix

Tektronix WFM90D Manual de usuario

Tektronix

Tektronix WFM5250 Manual de usuario

Tektronix

Tektronix WFM4000 Series Guía de configuración rápida

Tektronix

Tektronix 1740A Series Manual de usuario

Tektronix

Tektronix WFM2200A Manual de usuario

Tektronix

Tektronix MTM400 Manual de usuario

Tektronix

Tektronix 608 Manual de usuario

Tektronix

Tektronix WFM8200 Manual de usuario

Tektronix

Tektronix 4112 Manual de usuario

Tektronix

Tektronix WFM720UP Manual de usuario

Tektronix

Tektronix MTM400A Manual

Tektronix

Tektronix WFM2200 Manual de instalación y funcionamiento

Tektronix

Tektronix WFM2200 Cómo utilizar

Tektronix

Tektronix PRISM MPX2-DUALDSP Manual

Tektronix

Tektronix WFM4000 Series Manual de usuario

Tektronix

Tektronix D10 Manual de usuario

Tektronix

Tektronix WFM5200 series Cómo utilizar

Tektronix

Tektronix Sentry Manual de usuario

Tektronix

Tektronix 4023 Manual de usuario

Tektronix

Tektronix WFM 601i Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación