Tektronix RTPA2A Manual de usuario

Instruction Manual

RTPA2A

Real-Time Spectrum Analyzer

TekConnect®Probe Adapter

071-1766-01

www.tektronix.com

are protected by United States copyright laws and international treaty provisions.

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the

Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the

Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, as applicable.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX, TEK, TekConnect, and TeKProbe are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive or P.O. Box 500

Beaverton, OR 97077 USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

Warranty 2

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1)

year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its

option, either will repair the defective product without charge for parts and labor, or will provide a replacement in

exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work

may be new or reconditioned to like new performance. All replaced parts, modules and products become the

property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration

of the warranty period and make suitable arrangements for the performance of service. Customer shall be

responsible for packaging and shipping the defective product to the service center designated by Tektronix, with

shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a

location within the country in which the Tektronix service center is located. Customer shall be responsible for

paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage

resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;

b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been

modified or integrated with other products when the effect of such modification or integration increases the time

or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY

OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.

TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

RTPA2A Instruction Manual i

Table of Contents

General Safety Summary iii...................................

Environmental Considerations v...............................

Getting Started 1............................................

Cable Connections 1...............................................

USB Cable 1..................................................

Real-Time Spectrum Analyzer Software Compatibility 2.................

TekConnect Probe Compatibility 2....................................

Standard Accessories 3.............................................

Options 5........................................................

Installing the Probe Adapter 7........................................

CONNECTIONS Table 8........................................

Installing the USB Cable and Power Supply Cable 9......................

Installing the TekConnect Probe 10....................................

Performing a Functional Check 11.....................................

Operating Basics 17..........................................

Understanding the Controls 17........................................

Power Status 17................................................

USB Status 18..................................................

Probe Status 18.................................................

Reference 19.................................................

Avoiding Damage from Electrostatic Discharge or Overvoltage 19...........

Specifications 21.............................................

Certifications and Compliances 24.....................................

Maintenance 25..............................................

Inspecting and Cleaning 25...........................................

Troubleshooting 26.................................................

Product Requires Service 27..........................................

Repackaging for Shipment 27.........................................

Replaceable Parts 29.........................................

Parts Ordering Information 29.........................................

Using the Replaceable Parts List 30....................................

Table of Contents

ii RTPA2A Instruction Manual

List of Figures

Figure 1: The TekConnect probe adapter 1......................

Figure 2: Probe adapter inputs and outputs 7....................

Figure 3: Back panel connections 9.............................

Figure 4: Installing TekConnect probes 10.......................

Figure 5: Connecting the RTPA2A components 12.................

Figure 6: Check for lighted LEDs 13............................

Figure 7: Equipment setup with Real-Time Spectrum Analyzer 14...

Figure 8: Amplitude signal 15..................................

Figure 9: Location of status LEDs 17............................

Figure 10: Insertion loss 23....................................

Figure 11: Return loss 23......................................

Figure 12: Exploded view 34...................................

List of Tables

Table 1: Compatible probes 2.................................

Table 2: Standard accessories 3...............................

Table 3: Options 5..........................................

Table 4: Power cord options 5................................

Table 5: Recommended equipment for functional check 11.........

Table 6: Probe amplitude offset for Channel B 15.................

Table 7: Power status LED 17.................................

Table 8: USB status LED 18...................................

Table 9: Probe status LED 18..................................

Table 10: Electrical characteristics 21...........................

Table 11: Environmental characteristics 22......................

Table 12: Physical characteristics 22............................

Table 13: Probe adapter LEDs 26...............................

RTPA2A Instruction Manual iii

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it.

To avoid potential hazards, use this product only as specified.

Only qualified personnel should perform service procedures.

While using this product, you may need to access other parts of the system. Read

the General Safety Summary in other system manuals for warnings and cautions

related to operating the system.

Connect and Disconnect Properly. Do not connect or disconnect probes or test

leads while they are connected to a voltage source.

Connect the probe output to the measurement instrument before connecting the

probe to the circuit under test. Disconnect the probe input and the probe ground

from the circuit under test before disconnecting the probe from the measurement

instrument.

Ground the Product. This product is grounded through the grounding conductor

of the power cord. To avoid electric shock, the grounding conductor must be

connected to earth ground. Before making connections to the input or output

terminals of the product, ensure that the product is properly grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

The common terminal is at ground potential. Do not connect the common

terminal to elevated voltages.

Connect the ground lead of the probe to earth ground only.

Do not apply a potential to any terminal, including the common terminal, that

exceeds the maximum rating of that terminal.

Power Disconnect. The power cord disconnects the product from the power

source. Do not block the power cord; it must remain accessible to the user at all

times.

Do Not Operate Without Covers. Do not operate this product with covers or panels

removed.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Do Not Operate With Suspected Failures. If you suspect there is damage to this

product, have it inspected by qualified service personnel.

ToAvoidFireor

Personal Injury

General Safety Summary

iv RTPA2A Instruction Manual

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

Use Proper AC Adapter. Use only the AC adapter specified for this product.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Terms in this Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the

marking.

WARNING indicates an injury hazard not immediately accessible as you read the

marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. The following symbols may appear on the product:

CAUTION

Refer to Manual

Symbols and Terms

RTPA2A Instruction Manual v

Environmental Considerations

This section provides information about the environmental impact of the

product.

Observe the following guidelines when recycling an instrument or component:

Equipment Recycling. Production of this equipment required the extraction and

use of natural resources. The equipment may contain substances that could be

harmful to the environment or human health if improperly handled at the

product’s end of life. In order to avoid release of such substances into the

environment and to reduce the use of natural resources, we encourage you to

recycle this product in an appropriate system that will ensure that most of the

materials are reused or recycled appropriately.

The symbol shown to the left indicates that this product

complies with the European Union’s requirements

according to Directive 2002/96/EC on waste electrical and

electronic equipment (WEEE). For information about

recycling options, check the Support/Service section of the

Tektronix Web site (www.tektronix.com).

This product has been classified as Monitoring and Control equipment, and is

outside the scope of the 2002/95/EC RoHS Directive. This product is known to

contain lead, cadmium, mercury, and hexavalent chromium.

Product End-of-Life

Handling

Restriction of Hazardous

Substances

Environmental Considerations

vi RTPA2A Instruction Manual

Tabla de contenidos

Otros manuales de Instrumento de medición de Tektronix

Tektronix

Tektronix Keithley SourceMeter 2470 Manual de usuario

Tektronix

Tektronix 492, 492P Manual de usuario

Tektronix

Tektronix WVR7200 Instrucciones de instalación y mantenimiento

Tektronix

Tektronix 2715 Manual de usuario

Tektronix

Tektronix TDP3500 Manual de uso y cuidado

Tektronix

Tektronix 318 Manual de usuario

Tektronix

Tektronix 6 series Instrucciones de instalación y mantenimiento

Tektronix

Tektronix Keithley 6517B/E Manual de usuario

Tektronix

Tektronix P6139A Manual de usuario

Tektronix

Tektronix TTR500 series Manual de usuario

Tektronix

Tektronix RSA3408B Manual de usuario

Tektronix

Tektronix Keithley SourceMeter 2450 Manual de usuario

Tektronix

Tektronix TLA715 Series Manual de usuario

Tektronix

Tektronix RSA5100B series Instrucciones de instalación y mantenimiento

Tektronix

Tektronix 067 -0794-00 Manual de usuario

Tektronix

Tektronix RSA3303A Manual de usuario

Tektronix

Tektronix Keithley 2182A Manual de usuario

Tektronix

Tektronix 7T11 Manual de usuario

Tektronix

Tektronix IsoVu TIVP02 Manual de usuario

Tektronix

Tektronix 495 Manual de usuario

Tektronix

Tektronix TDS5032 Manual de usuario

Tektronix

Tektronix CSA7404B Manual de usuario

Tektronix

Tektronix P5210 Manual de usuario

Tektronix

Tektronix 7L13 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario