Tektronix P6417 Manual de usuario

Instructions

P6417 & P6418

Logic Analyzer Probes

071-0567-00

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Printed in the U.S.A.

Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and

workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this

warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor,

or will provide a replacement in exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration

of the warranty period and make suitable arrangements for the performance of service. Customer shall be

responsible for packaging and shipping the defective product to the service center designated by Tektronix, with

shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a

location within the country in which the Tektronix service center is located. Customer shall be responsible for

paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage

resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;

b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been

modified or integrated with other products when the effect of such modification or integration increases the time

or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’

RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.

TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR

THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

P4617 & P6418 Logic Analyzer Probe Instructions i

Table of Contents

General Safety Summary iii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preface v. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Related Documentation v. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contacting Tektronix vi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Basics 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Description 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Attaching Probe Labels 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the Probes 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reference 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Probe Connectors 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loading and Equivalent Circuits 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Functional Check 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection and Cleaning 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

P6418 Probe Service Procedures 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacing Podlets on the P6417 Probes 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repackaging Instructions 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replaceable Parts 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering Information 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Using the Replaceable Parts List 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

ii P4617 & P6418 Logic Analyzer Probe Instructions

List of Figures

Figure 1: P6417 and P6418 logic analyzer probes 1. . . . . . . . . . . . . . . .

Figure 2:Attaching probe labels 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 3: Connecting the logic analyzer probes 4. . . . . . . . . . . . . . . . . .

Figure 4: Connecting the probes to the target system 5. . . . . . . . . . . . .

Figure 5: Probe footprints 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 6: Probe podlet clearance 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 7: Probe loading 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 8: Probe functional verification test setup 11. . . . . . . . . . . . . . . .

Figure 9:Activity Monitor 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 10: Moving probe podlets 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 11: Disassembling the probe cable 15. . . . . . . . . . . . . . . . . . . . . . .

Figure 12: Removing the faulty channel from the probe cable

header housing 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 13: Removing a podlet cable from the rubber comb 17. . . . . . . .

Figure 14: Replacing a podlet in the podlet holder 18. . . . . . . . . . . . . . .

Figure 15: Installing the color-coded ring 19. . . . . . . . . . . . . . . . . . . . . . .

Figure 16: Installing the cable in the cable header housing 20. . . . . . . .

Figure 17: P6417 and P6418 Probe accessories 24. . . . . . . . . . . . . . . . . .

Figure 18: P6417 Probe exploded view 26. . . . . . . . . . . . . . . . . . . . . . . . .

Figure 19: P6418 Probe exploded view 27. . . . . . . . . . . . . . . . . . . . . . . . .

List of Tables

Table 1: Probe section and label combinations 2. . . . . . . . . . . . . . . . . .

Table 2: Electrical and mechanical specifications 9. . . . . . . . . . . . . . . .

Table 3: Environmental specifications 10. . . . . . . . . . . . . . . . . . . . . . . . .

P4617 & P6418 Logic Analyzer Probe Instructions iii

General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to

this product or any products connected to it. To avoid potential hazards, use this

product only as specified.

Only qualified personnel should perform service procedures.

While using this product, you may need to access other parts of the system. Read

the General Safety Summary in other system manuals for warnings and cautions

related to operating the system.

Connect and Disconnect Properly. Connect the probe output to the measurement

instrument before connecting the probe to the circuit under test. Disconnect the

probe input and the probe ground from the circuit under test before disconnecting

the probe from the measurement instrument.

Ground the Product. This product is indirectly grounded through the grounding

conductor of the mainframe power cord. To avoid electric shock, the grounding

conductor must be connected to earth ground. Before making connections to the

input or output terminals of the product, ensure that the product is properly

grounded.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and markings on the product. Consult the product manual for further ratings

information before making connections to the product.

Avoid Exposed Circuitry. Do not touch exposed connections and components

when power is present.

Do Not Operate With SuspectedFailures. If you suspect there is damage to this

product, have it inspected by qualified service personnel.

Do Not Operate in Wet/DampConditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Terms in this Manual. These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result

in injury or loss of life.

Symbols and Terms

General Safety Summary

iv P4617 & P6418 Logic Analyzer Probe Instructions

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

Terms on the Product. These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the

marking.

WARNING indicates an injury hazard not immediately accessible as you read the

marking.

CAUTION indicates a hazard to property including the product.

Symbols on the Product. The following symbols may appear on the product:

CAUTION

Refer to Manual

P4617 & P6418 Logic Analyzer Probe Instructions v

Preface

This document provides information on using and servicing the P6417 and

P6418 Logic Analyzer probes.

Related Documentation

In addition to these probe instructions, the following documentation is available

for your TLA 700 Series Logic Analyzer:

HThe TLA 700 Series User Manual provides overall user information for the

TLA 700 Series Logic Analyzer.

HThe TLA 700 Series Installation Manual provides installation information

for the TLA 700 Series Logic Analyzer.

HThe online help provides information about the TLA 700 Series user

interface and the TLA 700 Programmatic Interface (TPI). To view the online

help, select Help Topics from the Help menu.

HA series of instruction manuals for microprocessor support provide operating

and service instructions for the individual microprocessor support packages

that are available for use with the TLA 700 Series Logic Analyzer.

HThe P6434 Mass Termination Probe Instructions provides instructions for

using the P6434 probes.

HThe TLA 7QS Training Manual provides training exercises to help you learn

key features of the TLA 700 Series Logic Analyzer. The training manual is

designed to be used with the TLA 700 Series QuickStart training board.

HThe TLA 700 Series Performance Verification and Adjustment Technical

Reference Manual provides performance verification and adjustment

procedures for the major components of the TLA 700 Series Logic Analyzer.

The manual includes the performance verification and adjustment software.

HA series of service manuals that provide board-level service information for

major components of the TLA 700 Series Logic Analyzer.

Preface

vi P4617 & P6418 Logic Analyzer Probe Instructions

Contacting Tektronix

Product

Support For questions about using a Tektronix measure-

ment product, call toll free in North America:

1-800-833-9200

6:00 a.m. – 5:00 p.m. Pacific time

Or contact us by e-mail:

support@tek.com

For product support outside of North America, contact your

local Tektronix distributor or sales office.

Service

Support Contact your local Tektronix distributor or sales office. Or visit

our web site for a listing of worldwide service locations.

www.tektronix.com

Toll-free

Number In North America:

1-800-833-9200

An operator will direct your call.

Postal Tektronix, Inc.

Address P.O. Box 500

Beaverton, OR. 97077

USA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Tektronix

Tektronix

Tektronix TLA7012 Manual de usuario

Tektronix

Tektronix VM700T Manual de usuario

Tektronix

Tektronix P5102 Manual de usuario

Tektronix

Tektronix WVR8200 Manual de usuario

Tektronix

Tektronix P6021A Manual de usuario

Tektronix

Tektronix TLA6000 Series Manual de usuario

Tektronix

Tektronix TLA 714 Manual de usuario

Tektronix

Tektronix MTS4000 MPEG Manual

Tektronix

Tektronix OM2012 Manual

Tektronix

Tektronix P6231 Manual de usuario

Tektronix

Tektronix TDSUSB2 Manual de usuario

Tektronix

Tektronix VM700T Manual de usuario

Tektronix

Tektronix Keithley 2601B-PULSE Manual de usuario

Tektronix

Tektronix TLA6000 Series Manual de usuario

Tektronix

Tektronix P80318 Manual de usuario

Tektronix

Tektronix 4923 Manual de usuario

Tektronix

Tektronix PQA600A Manual de uso y cuidado

Tektronix

Tektronix PA1000 Manual de usuario

Tektronix

Tektronix RSA5100A Series Manual

Tektronix

Tektronix 1710J Series Manual de usuario

Tektronix

Tektronix 7D20 Manual de usuario

Tektronix

Tektronix 2714 Manual de servicio

Tektronix

Tektronix 7L13 Manual de usuario

Tektronix

Tektronix DSA8300 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario