Teknion interpret WWSTW Manual de usuario
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 3
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
Sept 2022 1 of 14
INT_012a
interpret
Installation Guides
120° Frame (WWSTW), Recessed Mid Gable (WWSMD), 120° Wire Gap
Worksurface (WWWTW), 120° Power Cut-Out Worksurface (WWWTC)
A - 120° Frame w/Legs x2
See page INT_012a_G02
for parts identification
B- 120° Frame without Legs x1
See page INT_12a_G03
for parts identification
E- Center Leg Assembly
(N02-2589) x1
D- Connect Bracket
(A16-1383) x3
C- Recessed Mid Gable
(WWSMD) x1
See page INT_012a_G03
parts identification
F- 120° Power Cut-Out
Worksurface
(WWWTC) x1
G- 120° Wire Gap
Worksurface
(WWWTW) x2
G
C
B
D
E
A
F
A
NOTE: Straight Legs layout shown.
NOTE: Refer to INT_404
for Power Door (WWEDR)
installation.
Leveler Cover is
located inside Leg,
assembled and
secured in place
with tape.
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 3
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
Sept 2022 2 of 14
INT_012a
interpret
Installation Guides
120° Frame with Legs ( x2 ) - Straight or Angled
A - End Leg Assy
Straight Leg
(N02-3686) x1
A5 -Center Rail
Extrusion Cap
(A23-4058) x1
A6 - Center Rail
Extrusion
(A23-3734) x1
A7 -Center Rail
End Cap Assy
(N02-2149) x2
A21 - 5/16X18-3.75"
Hex Cap
(E01-0799) x6
A14 - 5/16X18 Hex
Nut, 1/2 A/F
.265 THK
(E01-0755) x4
A13 - 5/16-18X2.5"
Socket Head
Cap Screw
(E01-0756) x4
A16 - 1/4-20X3-1/2
Flat Hd Mach.
Quadrex Screw
(E01-0771) x2
A17 - #10X0.875"
Quad. Pan Hd
Washer
(E07-0077) x6
A15- Cantilever
Bracket
(A16-4882) x1
A20 - Worksurface
Space Block
(A25-0547) x3
A19 - Front
Standoff
(B02-0658) x2
A18 - Cross Bar
(A16-4937) x1
A3 - End Leg Assy
Angled Leg
(N02-3687) x1
or
A1
A7
A5
A12
A18
A20
A19
A15
NOTE: Straight Leg Frames are shown in
this guide.
A8
N02-2090
A12 - Center Wing
Beam Assy
(N02-3706) x1
Pre assembled
A8 - Wing Beam
Assembly, 120
(N02-3707) x2
A11 -5/16X18 Hex
Nut, 1/2 A/F
. 265 THK
(E01-0755) x4
A9 - 5/16-18X2.5"
Socket Head
Cap Screw
(E01-0756) x4
A10 -5/16-18X2"
Socket Head
Cap Screw
(E01-0764) x2
Pre assembled
X02-0117
A22 - 5/16-18X2.5"
Socket Head
Cap Screw
(E01-0756) x1
A23 - 5/16X18 Hex
Nut, 1/2 A/F
. 265 THK
(E01-0755) x7
A6
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 3
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
Sept 2022 3 of 14
INT_012a
interpret
Installation Guides
120° Frame without Legs (x1), Recessed Mid-Gable (WWSMD)x1
B1 -Center Rail
Extrusion Cap
(A23-4058) x1
B2 -Center Rail
Extrusion
(A23-3734) x1
B3 -Center Rail
End Cap Assy
(N02-2149) x1
B15 -5/16X18-3.75"
Hex Cap Screw
(E01-0799) x6
B7 -5/16X18 Hex
Nut, 1/2 A/F
.265 Thk
(E01-0755) x12
B5 -5/16X18-2.5"
Socket Head
Cap Screw
(E01-0756) x8
B6 -5/16X18-2"
Socket Head
Cap Screw
(E01-0764) x2
B19 -#10X0.875"
Quad. Pan Hd
Washer
(E07-0077) x6
B11 -Cantilever
Bracket
(A16-4882) x2
B14 -Worksurface
Spacer Block
(A25-0547) x3
B12 -Front
Standoff
(B02-0658) x2
B13 -Cross Bar
(A16-4937) x1
B18 -1/4-20X3-1/2
Flat Hd Mach.
Quadrex Screw
(E01-0771) x2
C1 -
Mid Gable
Assembly
(N02-2053) x1
C2 -End Cap
(B02-0389) x2
N02-2090
B1
B2
B11
B4
B8
B12
B13
B14
C1
C2
B4 -Wing Beam
Assembly
(N02-3707) x1
Pre assembled
B8 -Center Beam
Assembly
(N02-3706) x1
B9 -5/16X18-2.5"
Socket Head
Cap Screw
(E01-0756) x8
B10 -5/16X18 Hex
Nut, 1/2 A/F
.265 Thk
(E01-0755) x8
Pre assembled
X02-0117
B16 -5/16X18-2.5"
Socket Head
Cap Screw
(E01-0756) x2
B17 -5/16X18 Hex
Nut, 1/2 A/F
.265 Thk
(E01-0755) x8
WWSMD
Side ViewSTEP 1: Remove Screws and Nuts from Beams required for End Gable installation. Save them
for future steps.
Section:
Description: Page No:
Date:
REMOVE SCREWS - END GABLE INSTALLATION DETAIL
INT_012a
4 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
End Gable
Connections
A14
A11
A9
A12
A8
A13
A8, A12
Section:
Description: Page No:
Date:
ATTACH CENTER BEAM TO END GABLE DETAIL
INT_012a
5 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 2: Attach longer, Center Beams to End Gables using sets of holes in the middle, as
shown.
End Gable Connection Side view
NOTE: There are
2 End Gables required
for this layout.
A12
A1
STEP 3: Fasten with previously removed Screws and Nuts, do not tighten.
A14
A13
Section:
Description: Page No:
Date:
PREPARATION FOR MID GABLE CONNECTION DETAIL
INT_012a
6 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 4: Relocate Clamp Brackets on the Beam Assemblies one hole ahead to create Mid Gable
Connection. Secure with 2 screws on each end. Save remaining screws and nuts for future step.
B4, B8
B7, B10
End
Gable
Connection
Mid
Gable
Connection
B4, B8
B5, B9
End Gable Connection
Mid Gable Connection
Save to use
in next steps.
Save to use
in next steps.
Section:
Description: Page No:
Date:
ATTACH CENTER BEAM TO MID GABLE FASTEN
INT_012a
7 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 6: Fasten with Screws and Nuts saved in previous step.STEP 5: Attach Center Beam Assembly to the Mid Gable. Attach End Caps making sure lids
open to the side.
B9
B10
C3
C1B8
Section:
Description: Page No:
Date:
CONNECT TO CENTER LEG ASSEMBLY CONNECT WING BEAM TO GABLES
INT_012a
8 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 8: Align Wing Beam Assemblies with holes on End and Mid Gables. Fasten with
previously saved Screws and Nuts.
STEP 7: Bring Mid and End Gable subassemblies to the Center Leg assembly. Connect loosely
with Bolts and Nuts.
B16
A11 NOTE: There are 4 Beams
to be connected to End Gable
and 2 to be connected to
Mid Gable in this layout.
Mid Gable
connection
End Gable connection
A10
B17
E1
End Gable Assembly
End Gable Assembly
Mid Gable Assembly
B10
A9
B9
A11
B4
A8
Section:
Description: Page No:
Date:
JOIN WING BEAMS TOGETHER ATTACH CROSS BARS
INT_012a
9 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 9: Remove Screws and Nuts from the ends of the Wing Beams. Line up Connecting
Brackets with indicated holes on Wing Beams. Fasten with previously removed Screws (shorter)
and Nuts. Save the rest for the next step. DO NOT TIGHTEN.
B7
B13
A10
A10
B7
A18 B7
A11
B6
D
A11
A10
B6
B7
STEP 10: Line up middle holes on Cross Bars with holes on beams as shown and place them
on the top of the frames so Bars cut-outs wrap around Center and Wing Beams. Fasten with
Screws (shorter) and Nuts. DO NOT TIGHTEN.
A11
A10
B6
B6
Section:
Description: Page No:
Date:
CANTILEVER AND SPACER PLACEMENT CENTER RAIL ASSEMBLY
INT_012a
10 of 14
Sept 2022
120° FRAMES, 120° WORKSURFACES, RECESSED MID GABLE
FRAMES, SUPPORTS AND WORKSURFACES
interpret
Installation Guides
STEP 11: Line up Cantilevers' middle holes with the holes on the Beams, as shown above.
Place Spacers a the end of the Beams, line up with holes on the Leg plate. Push Front Standoff
to wrap around the Wing Transverse Beams in the middle location.
B11
B12
A15
A19
A20
B14
A15
A19
A20
B14
NOTE: Install electrical components if specified.
Refer to INT_401a, 406a, 408c Guides.
STEP 13: Insert Hex Cap Screws inside the underside channels. There should be 6 Screws per
Rail. Install End Caps on. Tighten set screws with Allen Key to secure End Caps in place. Slide
Screws along the channel into approximate location to line up with Clamp and Cantilever
Brackets, Cross Bar and Spacer.
A21, B15
A6, B2
A7, B3 Side view
Tighten set screws
NOTE: For this example there is
only 1 End Cap for Center Rail
with Mid Gable.
Este manual sirve para los siguientes modelos
3
Otros manuales de Rack y soporte de Teknion
Teknion
Teknion transit Manual de usuario
Teknion
Teknion YMSTA Instrucciones de funcionamiento y mantenimiento
Teknion
Teknion YMSTR Manual de usuario
Teknion
Teknion Interpret Instrucciones de funcionamiento y mantenimiento
Teknion
Teknion Interpret Instrucciones de funcionamiento y mantenimiento
Teknion
Teknion THSCD Manual de usuario
Teknion
Teknion JNSASW Manual de usuario
Teknion
Teknion district SUPPORT FOOT FOR DISTRICT FREESTANDING WITH GLASS PANEL... Manual de usuario
Teknion
Teknion complements CEREBRO Instrucciones de funcionamiento y mantenimiento
Teknion
Teknion HNBEBF Instrucciones de funcionamiento y mantenimiento
