TA-605
(1)(2) Line Input/Sub-Input : This allows connection to any head unit that has a RCA outputs.
(3) Input-selector switch : The sub outputs si
nal is a sum of the Ch1+2(Front) and ch3+4(Rear) outputs.
All three inputs will accept si
nal for use with a head unit with three preamp outputs.
1) When set to "1+2Ch" position, the front Inputs (Ch1+2) will provide si
nal for the entire Amplifier.
2) When set to "1+2Ch, 3+4Ch" position, both the front and rear inputs will accept si
nal allowin
the use of head unit fader.
3) When set to "1+2Ch, 3+4Ch, SUB" all three inputs wil accept si
nal seperately for use with a headunit with thre preamp outputs.
(4)(7)(11) LEVEL : This allows level ad
ustment of the input si
nal. Use this control to correctly match the head unit to 3/4 volume, with the
BASS and TREBLE on zero, then slowly turn up the amplifier level control towards the MAX end of the control, NOTE : If the sound becomes
distorted, turn this control down.
(5)(8)(10) "Hi
h-Pass" frequency control : This control is active when the switch is set to "Hi-pass" and permits selection of the
desired crossover frequency.
(5)(8)(10) "Low-Pass" frequency control : This control is active when the switch is set to "Low-pass" and permits selection of the
desired crossover frequency.
(6)(9)(12) CROSSOVER SELECTOR : Set the appropriate mode of operation. The 3 positions available are FLAT, HIGH PASS and LOW PASS.
(13) POWER LED : When illuminated the amplifier is turned on.
(14) PROTECTION LED : When illuminated it indicates a fault has occurred. Check installation.
(15) +12V : This must be connected directly th the vehicle batteries positive(+) terminal via an inline fuse at the battery end.
Note : This is to be the lasst wire to hook up durin
installation as dama
e could result.
(16) REMOTE : This terminal is for turnin
the amplifier on and off. This requires a requires a switched positive (+12V) to power "on" the
amplifier, this can be found on the rear of the head unit in the form of a electric antenna output, or a remote on output. Of not available you
can wire to the ACC position on the key.
(17) GROUND : Connect directly to the vehicle's chassis.
NOTE : This is to be the first wire to hook up durin
installation as dama
e could result.
(18) FUSE : Please ensure correct type of fuse is fitted, as specified in this manual.
(19) Loudspeaker connections : (If the amplifier is to be connected in a brid
ed mode, proceed with the section "Brid
ed loudspeaker
connections".) As with any audio component, connection of the amplifier and speakers with the correct polarity is essential for
oods bass
reproduction. Ensure there fore when connection that the positive (+) loudspeaker terminal.
The same applies to the ne
ative (-) terminals. The left-hand amplifier channel must also be connected to the left-hand loudspeaker and the
ri
ht-hand the ri
ht-hand amplifier channel to the ri
ht-hand loudspeaker.
r
e
ou
spea
er
connec
ons
:
e
can
a
so
e
r
e
n
a
mono
con
ura
on.
s
ena
es
you
o
use the amplifier for one or more subwoofer(s) or amid-ran
e speaker. In this confi
uration the amplifier sums the ri
ht-hand and oeft-hand channel
deliverin
a sin
le channel (mono) output.
Note : The amplifier can sum the ri
ht-and oeft-hand si
nal information only both the ri
ht-and left-hand RCA connections have been made.
CAUTION : The amplifier must be presented with a load of 4 Ohms or higher in bridged mode. A lower load will cause the amplifier
to overheat or switch off. This can lead to permanent damage of the unit
5 Channel Feature Guide
5 Channel
RMS 60Wx4CH+165Wx1CH
