Technomate TM-55 HD POE Manual de usuario
TM-55 HD POE
Please note: the Default EDID is 1080p@60Hz 2.1CH therefore the HDMI Receiver
will output the video & audio according to this. If your display supports a different
resolution and/or audio channel, please adjust the EDID as on Page 5.
We recommend to press the Sync button after you have finished connecting the units.
Mode DIP 1 DIP 2 DIP 3 EDID Info
1
2
3
4
5
6
7
8
0
1
0
1
1
0
0
0
1
1
0
1
0
0
1
0
1
720P@50Hz 2.1CH
720P@50Hz 7.1CH
720P@60Hz 2.1CH
1080i@60Hz 2.1CH
Default: 1080P@60Hz 2.1CH
1080i@60Hz 7.1CH
1080P@60Hz 7.1CH
Read & Save the EDID of the
HDMI Loop-Out Display
Note: 1 = Switch UP; 0 = Switch DOWN
6. CAT CONNECTIONS
1. Recommended Cabling:Full Copper shielded CAT5e/6
2. Connection Precautions:
To reduce video dropouts from fans and other EMI issues,
it is recommended that shielded CAT5/6 with shielded RJ45
connectors are used. Easy style connectors are not
recommended.
5 6
7. SPECIFICATIONS
Please note: the Default EDID is 1080p@60Hz 2.1CH therefore
the HDMI Receiver will output the video & audio according to
this. If your display supports a different resolution and/or
audio channel, please adjust the EDID as in the following table:
0 0 0
0
1 1
1
Resolutions Supported 480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz
HDCP 1.4
Transmission Distance Up to 55m using Full Copper CAT6
IR 20 ~ 60 KHz
HDMI 1.3
Power Consumption <3W (TX), <2W (RX)
Operating Temperature 0~60 °C
Power DC5V 2A
Dimensions 82 x 67 x 15mm
Weight ~100g（TX），~100g（RX）
1. IMPORTANT SAFETY INSTRUCTIONS
1. To prevent fire or shock hazard, do not expose any part of the
devices to rain or moisture.
2. This product is for indoor use only
3. Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers)
that produce heat.
4. Clean only with a dry cloth.
5. Protect the power cord from being walked on or pinched
particularly at plug, convenience receptacles, and the point
where it exits from the apparatus.
6. Unplug this apparatus during lightning storms or when unused
for long periods of time.
7. Refer all servicing to qualified service personnel.
8. Do not expose this equipment to dripping or splashing and
ensure that no objects filled with liquids, such as vases, are
placed on the equipment.
9. This device should be operated using only the AC/DC adaptor
supplied with it.
10. Do not overload wall outlets and extension cords as this can
result in the risk of fire or electrical shock.
2. CONTENTS
1x HDMI Transmitter
1x HDMI Receiver
1x Wideband 20-60kHz IR Blaster
1x Wideband 20-60kHz IR Receiver
1x 5V 2A DC Power Supply Adaptor
1x Owner's Manual
3. CONNECTIONS
Transmitter: HDMI with HDMI Loop-out to CAT
1. For IR Blaster Cable
2. CAT Output
3. Reset
4. DC5V Power Input
5. HDMI Loop-out
6. EDID
7. HDMI Input from source
Receiver: CAT to HDMI
1. DC5V Power Input: if low quality
CAT cable is used, you may need
to use an additional DC5V power
adaptor (sold separately) to amplify
the signal. With full Copper CAT6
cable up to 55m, no power is
required (PoE)
④
2. HDMI Output to display
3. For IR Receiver Cable
4. Sync: pairs the units
5. CAT Input
6. Link: LED is ON when
an HDMI output is
detected
4. INSTALLATION
①② ③ ⑤ ⑥ ⑦
①② ③ ⑤ ⑥
1. Connect a source device to the HDMI Input on the Transmitter.
2. If using the HDMI Loop-Output, connect a display to the HDMI
Out on the Transmitter.
3. Connect a single CAT 5e/6/7 up to 55m from the CAT Output
of the Transmitter to the CAT Input of the Receiver.
4. Connect a display from the HDMI Output on the Receiver.
5. If using the IR cables, connect the IR Blaster to the IR IN in the
Transmitter; and the IR Receiver to the IR OUT on the Receiver.
6. Plug the power supply into the Transmitter DC5V power socket
and plug the power adaptor into a mains socket.
5. EDID
The display used within an installation may not support all
resolutions available from a source. It is necessary to make sure
the source will provide a video and audio format compatible with
the connected display. To accomplish this, the Transmitter
includes built-in EDID management for the source input.
CAT5e/6/7
④
2 3 4
4
Otros manuales para TM-55 HD POE
1
Otros manuales de Extensor de Technomate
