Technische Alternative RAS-PLUS Manual de usuario

RAS-PLUS (/F)

Version 1.10 EN

Room sensor

with remote display

RAS-PLUS = Room sensor with

temperature measurement and remote

display

RAS-PLUS/F = Room sensor with

temperature and humidity measure-

ment and remote display

Operation

Programming

Installation instructions

Table of Contents

Function description ........................................................................................4

Programming manual.......................................................................................5

Menu – general overviews................................................................................................6

Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611.....................................6

Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-3 (from version 8.3),

UVR63 (from version 1.5)................................................................................................7

Menu overview for all other controllers............................................................................8

Menu CONFIG....................................................................................................................9

Language selection SPR DE/LAN EN.............................................................................9

Time interval for continuing display TIME N....................................................................9

Time before jumping back to the 1st display TIME B ....................................................10

Address in the DL-bus network DL ADR .......................................................................11

Index specification.........................................................................................................12

Entry of an offset value for sensor correction OFFSET.................................................13

Display of operating mode symbols SYMB ...................................................................14

Menu VALUES..................................................................................................................15

Menu sensor values SENSOR......................................................................................15

Menu output statuses OUTPUT ....................................................................................16

Menu speed stages SPEED (only UVR1611) ...............................................................17

Menu heat quantity counter POWER ............................................................................18

Menu external sensors NETW (only ESR21 (from version 5.0), ESR31, UVR61-3 (from

version 8.3), UVR63 (from version 1.5))........................................................................19

Menu analog CAN network inputs ANALNW (only UVR1611) ......................................20

Menu digital CAN network inputs DIGINW (only UVR1611)..........................................21

Menu symbol allocation SYMB......................................................................................22

Deleting or changing a symbol allocation:.....................................................................24

Reset to factory setting...................................................................................................25

Operation.........................................................................................................26

Room sensor with UVR16x2, RSM610, CAN-I/O45, UVR1611(from vers. A3.00 and

serial number 13286) or with UVR63-H(from vers. 7.2) ................................................26

Use as a remote control..................................................................................................27

Room sensors with other controllers............................................................................27

Installation.......................................................................................................27

Electrical connections ....................................................................................................27

Technical data.................................................................................................27

Function description

The room sensor RAS-PLUS was specially developed for Technical Alternative control

units and is intended for mounting in the living area (reference space). The room sensor

should not be installed near a source of heat or near a window. It is only suitable for opera-

tion in dry rooms.

The RAS-PLUS transmits the room temperature, relative room humidity (only RAS-PLUS/F)

and the dew point (only RAS-PLUS/F), the operating mode and the correction value for the

nominal value (+/- 5K) to the controller via the bidirectional data link (DL-bus). Using the DL-

bus it is also possible to display controller sensor values, output states, heat quantity counter

outputs and network inputs at the RAS-PLUS (remote display). Programming of the sensor

permits the setting of which values and symbols are to be output to the display. Moreover

there is a choice between automatic or manual scrolling between the displays.

The sensor RAS-PLUS can be used with the following controllers as a room sensor with

remote display:

UVR 16x2

RSM 610

CAN-I/O 45

UVR 1611 from version A3.00 and serial number13286

UVR 63-H from version 7.2

UVR 63 from version 1.0

UVR 61-3 from version 5.0

ESR 31 from version 1.0

ESR 21 from version 5.0

Moreover the RAS-PLUS can also be used with the following controllers as a remote dis-

play device (without sensor functions):

UVR 31

UVR 42

UVR 64

HZR 65

UVR 1611 < version A3.00

UVR 63-H < version 5.0

UVR 61-3 < version 5.0

ESR 21 < version 5.0

These controllers do not have a bidirectional data link.

Programming manual

Only the basic values are displayed in the factory setting of the room sensor:

Room temperature

Relative Room humidity (only RAS-PLUS/F)

Nominal value adjustment (+/- 5K)

With the aid of programming other values can be displayed.

Access to the programming level is only possible from the "Standby" position

(extreme left) of the slider switch.

RAS-PLUS can be configured using the key and set up to display further values.

The following symbols are used in the menu descriptions to differentiate between long and

short key presses:

Long key press (at least 2 seconds)

Short key press

Multiple short key presses

Further information about the menu views:

Red printed numbers or symbols mean that they flash in the display.

Exiting from a menu level is always only possible from the "EXIT" display

indication by a long key press.

Menu – general overviews

The displayed menu options are matched to the respective controller types:

Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

V 1 10 = Sensor version number

Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-

3 (from version 8.3), UVR63 (from version 1.5)

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

V 1 10 = Sensor version number

Menu overview for all other controllers

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

The menu option "POWER" (heat

quantity counter) is only displayed

with those controllers that have this

function.

V 1 10 = Sensor version number

Menu CONFIG

The following settings are made here:

Language selection SPR DE / LAN EN

Time interval for continuing display TIME N

Time before jumping back to the 1st display TIME B

Address in the DL-bus network DL ADR

Entry of an offset value for sensor correction OFFSET

Language selection SPR DE/LAN EN

Switchover between German (DE) and

English (EN)

Factory setting: DE

To activate the language selection the RAS-PLUS must be initialised by scrolling forward in

the display level.

Time interval for continuing display TIME N

Entry 0 = no automatic forwarding between

the displays

Factory setting: 0

After a long key press "0" flashes

Selection of the desired time by a short key

press.

Confirmation of the desired time by a long

key press.

Entry 15 = The value display scrolls for-

wards every 15 seconds to the next display.

Adjustment range: 0 – 99 sec in second

steps

Time before jumping back to the 1st display TIME B

Entry = 0 There is no jump back of the dis-

play to the 1st value.

Factory setting: 0

After a long key press "0" flashes

Selection of the desired time by a short key

press.

Confirmation of the desired time by a long

key press.

Entry 60 = After 60 seconds without activa-

tion of the key button jumping back from

one of the additional programmed values to

the first display value (room temperature)

occurs. Adjustment range: 0 – 100 sec in

10 second steps

The jump back occurs only from the additionally programmed display values, not from one of

the base values.

Note: Only one of the two time options TIME N or TIME B should be selected.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Technische Alternative

Technische Alternative

Technische Alternative RAS PLUS DL Manual de usuario

Technische Alternative

Technische Alternative RAS+DL Manual de usuario

Technische Alternative

Technische Alternative RAS-F Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario