TechNexion TEK3-BSW Manual de usuario

3.1 Surface Mounng

TEK3-BSW

Quickstart Guide

3 Installaon Instrucons

This secon describes the mounng procedures for TEK series device. The material in the mounng area must provide suﬃcient strength for support of this embedded

box PC.

There are 4 mounng holes (M5) on the front side of the device required for surface mounng. Four M4 or M5 screws with at least 8mm head-to-p length are

required to secure this device to the surface.

3.2 DIN Mounng

The device can be mounted on a DIN rail by using a DIN-rail bracket. There are four mounng holes (M3) on the rear side of the device required for DIN bracket

mounng (30mm DIN rail standard). Secure the DIN bracket to the back of this device by using two M3 screws with at least 5mm head-to-p length.

INNOVATORS OF TECHNOLOGY

Top view:

Boom view:

2 Dimensions

1 Safety Precauons

Thank you for purchasing a TechNexion TEK series device. This installaon guide will be helpful in the installaon, wiring and inspecon of your TechNexion embedded

fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precauons before proceeding with

the installaon, wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference. The following suggesons will help you.

• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,

allow it to dry completely.

• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.

• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage baeries, and warp or melt certain plascs.

• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

• Do not aempt to open the device. This product is designed for speciﬁc applicaons and needs to be installed by qualiﬁed personnel.

• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and ﬁne mechanics.

• Do not paint the device. Paint can clog the parts and prevent proper operaon.

• Unauthorized modiﬁcaons or aachments could damage the device and may violate regulaons governing radio devices.

• Do not touch any internal or exposed parts of the device as electrical shock may result.

• Do not open the device while power is on. Otherwise electrical shock may result.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to bad venlaon or overheang.

These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service

facility for service.

•Make sure that the available power source matches the required input power of the device. Failure to observe this cauon may result in electric shock or ﬁre.

•Do not power the unit by DC input when you apply power over the PoE (RJ45).

1.1 Storage and Installaon

1.2 Wiring

1.3 Maintenance and Inspecon

Unit : mm

168

109

71.5

157

54.2

1 2

4 External Connectors

without the prior wrien permission of TechNexion Ltd.

• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied by law no liability (including liability to any person by reason of

negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.

• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version at: hps://www.technexion.com/support/download-center/

Phone: +886-2-82273585 Web: www.technexion.com

16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan

2019-05-27

5.1 Galvanic Isolated Connectors Pin Deﬁnion(TEK3-xxxxx-Rxx-Lxxx-xxx-xxxx-XG21-xxxx-xxxx) (oponal)

5.2 Non-Galvanic Isolated Connectors Pin Deﬁnion (TEK3-xxxxx-Rxx-Lxxx-xxx-xxxx-XS21-xxxx-xxxx) (oponal)

5.1.1 Galvanic Isolated Serial Port Connector (RS-XXX) (oponal)

5.1.2 Galvanic Isolated Digital I/O Connectors (GPIO1 / GPIO2) (oponal)

5.2.1 Non-Galvanic Isolated Serial Port Connector (RS-XXX) (oponal)

5.2.2 Non-Galvanic Isolated Digital I/O Connectors (GPIO1 / GPIO2) (oponal)

5 Addional I/O Connectors: GPIO1, GPIO2, and RS-XXX (oponal)

6 LED Light Indicators

This product is available with three oponal connectors: GPIO1, GPIO2, and RS-XXX that can be ordered in either a galvanic

isolated or non-galvanic isolated version.

The dual 4-wire galvanic isolated serial port is set by default as follows: The primary and secondary serial ports are both set as

RS-232 during manufacturing. For seng details of TEK3-BSW serial ports in other modes, please refer to the TEK3-BSW

HARDWARE MANUAL.

The dual 4-wire non-galvanic isolated serial port can be conﬁgured as follows: The primary and secondary serial port can only be

used as a standard RS-232.

The TEK3-BSW has four programmable LED Light indicators.

For detailed sengs informaon of the TEK3-BSW GPIO ports, please refer to the TEK3-BSW HARDWARE MANUAL.

Header: Molex 43045-1012 (10-pin Micro-Fit 3.0).

Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

For detailed sengs informaon of the TEK3-BSW GPIO ports, please refer to the TEK3-BSW

HARDWARE MANUAL.

Header: Molex 43045-0800 (8-pin Micro-Fit 3.0).

Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

Header: Molex 43045-1000 (10-pin Micro-Fit 3.0).

Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

Description No.No. Description

USB Host connector

HDMI connector

miniDP connector

USB OTG (Type-C) connector

LAN2 RJ45 connector

3.5mm jack Line out

3.5mm jack Line in

3.5mm jack Mic in

Power Input connector

LAN1 RJ45 connector

GPIO1 connector (optional)

GPIO2 connector (optional)

RS-XXX (Serial Port) connector (optional)

Power button

Reset button

Micro-SIM cardslot

MicroSD cardslot

LED Light 1 indicator

LED Light 2 indicator

LED Light 3 indicator

LED Light 4 indicator

Antenna hole

LED# Color

PCB Location

Registered Address

1 LED-D12

LED-D11

LED-D10

LED-D9

Green

0xFED8C400_BIT1(Memory)

0x99_BIT7(SIO)

0x81_BIT0(SIO)

0xE1_BIT4(SIO)

RS-XXX:

GPIO1/GPIO2:

RS-XXX:

DIG_IN1

DIG_IN2

Ground for digital I/O

Common Ground

DIG_OUT5

DIG_OUT6

Supply input for digital I/O

Supply output

Max. 5.25V

Max. 12.39V

12V

Voltage

GPIO1A

GPIO1B

GND_DIO

GND

GPIO1C

GPIO1D

VCC_DIO

VCC

DIG_IN1

DIG_IN2

Ground for digital I/O

Common Ground

DIG_OUT5

DIG_OUT6

Supply input for digital I/O

Supply output

GPIO2A

GPIO2B

GND_DIO

GND

GPIO2C

GPIO2D

VCC_DIO

VCC

Port Pin #

GPIO1 Signal

GPIO1 Description

GPIO2 Description

GPIO2 Signal

1234

5678

Header: Molex 43045-0800 (8-pin Micro-Fit 3.0).

Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

Note: LED Light 4 indicator is set as Power LED during manufacturing. The Power LED Light indicator is lit,

when the system is powered on.

GPIO1/GPIO2:

INDICATOR:

DIG_IN1/OUT1

DIG_IN2/OUT2

Common Ground

DIG_IN5/OUT5

DIG_IN5/OUT6

Supply Output

3.3V

12V

Voltage

GPIO1A

GPIO1B

GND

GPIO1C

GPIO1D

VCC

DIG_IN1/OUT1

DIG_IN2/OUT2

Common Ground

DIG_IN5/OUT5

DIG_IN5/OUT6

Supply Output

GPIO2A

GPIO2B

GND

GPIO2C

GPIO2D

VCC

Port Pin #

GPIO1 Signal

GPIO1 Description

GPIO2 Description

GPIO2 Signal

1234

5678

Front view:

31 2 4 579

10 11 12 13 14

Rear view:

23 24 25 26

15 16 17 18 19 20 21 22

12345

678910

Port Pin #

RS-232 + RS-232 (default)

Device

GND

SERIAL1A_TXD

SERIAL1A_RXD

SERIAL1A_RTS

SERIAL1A_CTS

GND

SERIAL1B_TXD

SERIAL1B_RXD

SERIAL1B_RTS

SERIAL1B_CTS

GND

SERIAL1A_TXD

SERIAL1A_RXD

SERIAL1A_RTS

SERIAL1A_CTS

GND

SERIAL1B_TXD

SERIAL1B_RXD

SERIAL1B_RTS

SERIAL1B_CTS

RS-232 + RS-422 RS-232 + RS-485

GND

SERIAL1A_TXD

SERIAL1A_RXD

SERIAL1A_RTS

SERIAL1A_CTS

GND

SERIAL1B_TXD+

SERIAL1B_RXD-

SERIAL1B_RXD+

SERIAL1B_TXD-

GND

SERIAL1A_TXD

SERIAL1A_RXD

SERIAL1A_RTS

SERIAL1A_CTS

GND

SERIAL1B+

SERIAL1B-

COM1

COM2

12345

678910

Port Pin #

RS-232 + RS-232

Device

COM1

COM2

The unit is by default preloaded with soware that can download and install a selecon of Linux OS images over hardwired network. Simply connect a display to the

unit though the miniDP or HDMI connector and a network through the Ethernet LAN RJ45 connector and power it up, then follow the steps on the screen to load the

soware.Local proxies will interfere with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/

To download drivers for the Windows operang systems, go to our Download Center at:

hps://www.technexion.com/support/download-center/

For more informaon about installing and conﬁguring the Windows operang systems, see: hps://msdn.microso.com/en-us/

7 Soware and Driver Installaon

3 4

Otros manuales para TEK3-BSW

Otros manuales de De oficina de TechNexion