Technaxx TX-111 Manual de usuario

Technaxx®* User Manual

WiFi Rear Camera System TX-111

Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.)

as assistance for reverse parking.

This system should be an aid and should NOT replace the need to drive

carefully.

NOTE: the Smartphone in the car may only be used if it is firmly fixed in

a holder.

Under no circumstances will the manufacturer or supplier accept any

responsibility or can held liable for any direct or indirect, incidental or

consequential damage, or for injuries resulting from installing or use of

this system.

The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares

that this device, to which this user manual belongs, complies with the

essential requirements of the standards referred to the Directive RED

2014/53/EU. The Declaration of Conformity you find here:

www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before

using the device the first time, read the user manual carefully.

Keep this user manual for future reference or product sharing carefully. Do

the same with the original accessories for this product. In case of warranty,

please contact the dealer or the store where you bought this product.

Warranty 2 years

Features

Inconspicuous reversing camera in license plate holder

Suitable for most vehicles as assistance for reverse parking

Video stream over WiFi on Smartphone via APP (New Sight)

Wireless video transmission up to ~10m

IR LED for clear night vision ~4m

Adjustable camera alignements & 110° viewing angle

IP67 camera protection class (dustproof & protection against

temporary immersion)

License plate holder suitable for single-line EC registration

(52x11cm)

Complete installation set

More safety in reverse driving

Technical specifications

License plate holder with camera

Image sensor / Resolution CMOS / 640x480 pixel

Viewing angle 110°

Min. illumination 0.5Lux / automatic white balance

IR night vision distance ~4m

Power supply Connection via WiFi transmitter

Max. current 210mA (incl. transmitter)

Protection class IP67

Weight / Dimensions 264g / (L) 52.8 x (W) 4.0 x (H) 13.7cm

WiFi Transmitter

Modulation (CCK,DQPSK,DBPSK),OFDM(BPSK,

QPSK,16QAM,64QAM)

Protocol IEEE802.11b/g/n

Encoding WPA2

Transmission frequency 2.4GHz

Max. radiated output power

10mW

Weight / Dimensions 72g / (L) 9.5 x (W) 4.0 x (H) 1.4cm

Input voltage DC 12V

Transmission distance ~10m open space (no interferences)

Operating temperature –10°Cup to +50°C

APP name / version New Sight / iOS version 7.0 and higher and

Android version 4.4 and higher

Weight / Dimensions 65g / (L) 9.0 x (W) 3.5 x (H) 1.2cm

Packing

Contents

License plate holder with camera, WiFi transmitter

with power connection for the camera, Mounting

material, User Manual

Hints for Environment Protection: Packages materials are

raw materials and can be recycled. Do not disposal old

devices or batteries into the domestic waste. Cleaning:

Protect the device from contamination and pollution (use a

clean drapery). Avoid using rough, coarse-grained materials or

solvents/aggressive cleaner. Wipe the cleaned device

accurately. Distributor: Technaxx Deutschland GmbH &

Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany

Product overview

The rear view camera sends a video signal from the camera via

WiFi to the smartphone. In case another Bluetooth handsfree

device is installed in your vehicle, it works in the same frequency

range as the camera. If that handsfree device is activated, it may

cause disturbances. Therefore we recommend to deactivate that

other Bluetooth handsfree device while using the reversing system.

License plate holder with camera

Infrared-LED 3 Holder

Camera 4 Connection cable

WiFi Transmitter

Connection cable to the

electrical system 2 Connection cable to camera

WiFi status LED on the WiFi transmitter box:

RED: WiFi is being set up

GREEN: WiFi is ready for connection

Commissioning

Check the functionality of the components before installation (a

installed product is excluded from the return). Preparing and

installing the license plate holder and the transmitter unit.

NOTE: You may need a voltmeter to measure the polarity of the

electrical system.

Break the two locks carefully out of the holder.

Remove the transport locks carefully. Use a sharp knife or a

tong.

 Attach the license plate holder to the vehicle instead of your

previous license plate holder.

 Insert the camera cable into the trunk compartment and

connect it to the transmitter unit.

 Attach the transmitter unit steady and firm in the trunk

compartment.

 Connect the black connection cable of the WiFi

transmitter to the negative pole of the 12V electrical system (on

board-voltage).

 Connect the red connection cable of the WiFi

transmitter to the positive pole of the 12V electrical system (on

board-voltage). You can use any 12V voltage that is switched on or

off with the ignition or the light (rear light). A connection with 12V

continuous plus is not recommended because of the power

consumption. It is also not recommended to connect to the

reversing light as the WiFi transmitter will take about 10 seconds to

establish a connection.

Using the cable clamps

The pictures explains how to use the supplied cable clamps.

1. Put the cable from

the car you want to

connect the WiFi

transmitter with into

the clamp.

2. Insert the 2nd

cable (red or black

cable of the WiFi

transmitter).

3. Close the clamp.

Insert the license plate in the holder

The following drawings show in sequence the insertion of the

license plate.

1. Step

Slide the license plate into the upper

opening.

 Press the number plate towards

the holder.

2. Step

 Slide the license plate down

until it stops.

3. Step

 Insert the locks from above

into the holder.

(You carefully broke them out of the

holder in the first step.)

 Set the camera at an angle where you have a good

view to the rear, depending on the height of the license plate holder

from the ground.

The displayed lines on the Smartphone give you an indication of the

distance.

Definitely control the distance with a folding ruler.

Explanations for the installation of the Smartphone APP can be

found on the following pages.

 Then tighten the screws on both sides of the camera.

Download & install the APP

For the TX-111 you get for Apple iOS (from 7.0) and Android (from

4.4) a suitable APP.

iOS: Download and install the APP

Open the APP-Store or Scan the QR-

code.

In the search field enter New Sight.

Select New Sight under the search

results and confirm with Install.

After the app is installed, you will see a

corresponding icon

Setting up the WiFi connection:

Go to Settings of your Smartphone.

Open WiFi.

Select WIFICAMERA as WiFi

connection.

At initial startup, enter the following

dialog as Password 88888888 (8x8).

The connection is made.

 Open the APP New Sight.

Android: Download and install the APP

Open the Playstore or Scan the QR-

code.

In the search field, enter New Sight.

Select New Sight under the search

results and confirm with Install.

After the app is installed, you will see

a corresponding icon on the screen.

Setting up the WiFi connection:

Go to Settings. open WiFi.

In the WiFi list, select WIFICAMERA.

At initial startup enter the password

88888888 (8x8).

The connection is made.

 Open the App New Sight.

Start/Open the APP New Sight

Take a snapshot of the current live view

List of taken and saved pictures on your Smartphone.

Take a video of the current live view.

List of taken and saved videos on your Smartphone.

Horizontal reflection (mirror) of the live view

Customize the WiFi name and WiFi password of the WiFi

transmitter. It is suggested to change the name and the

password after the first use. After changing WiFi name

and password you need to reconnect your phone to the

new WiFi. Enter the new given password.

Tips, Note & Attention

A brief tap on the display will hide the menu.

The displayed lines are intended only as an aid to estimating the

distance. To get a feel for it, you should do a driving exercise.

When transferring the images, there is a systemic delay. This

delay is in the range of one-half to one second. They should take

this time into consideration when driving backwards.

Problem and solution

You will only get a gray picture, even though the LED on the

WiFi transmitter box is green.

 In this case, you should reset the WiFi transmitter box. Press

with a pen into the marked RESET button on the WiFi transmitter.

Reset 2 WiFi Status

RED: WiFi is being set up

GREEN: WiFi is ready for connection

 Then disconnect the power supply and restore the

connection after approx. 20 seconds. Check if the WLAN

connection is available again.

NOTE: In some cases it may also be necessary to uninstall and

reinstall the App New Sight.

Safety regulations

The reversing system is an aid and does not relieve the driver of his

duty of care in road traffic according to STVO. Please read these

instructions carefully before first use.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Technaxx

Technaxx

Technaxx BT-X22 Manual de usuario

Technaxx

Technaxx TX-123 Manual de usuario

Technaxx

Technaxx TX-140 Manual de usuario

Technaxx

Technaxx TX-134 Manual de usuario

Technaxx

Technaxx TX-119 Manual de usuario

Technaxx

Technaxx TX-169 Manual de usuario

Technaxx

Technaxx BT-X22 Manual de usuario

Technaxx

Technaxx TX-168 Manual de usuario

Technaxx

Technaxx TX-90 Manual de usuario

Technaxx

Technaxx TX-110 Manual de usuario

Technaxx

Technaxx Pro TX-168 Manual de usuario

Technaxx

Technaxx BT-X22 Manual de usuario

Technaxx

Technaxx TX-159 Manual de usuario

Technaxx

Technaxx FMT1200BT Manual de usuario

Technaxx

Technaxx MusicMan BT–X25 Manual de usuario

Technaxx

Technaxx TE17 Manual de usuario

Technaxx

Technaxx TE15 Manual de usuario

Technaxx

Technaxx BT-X30 Manual de usuario

Technaxx

Technaxx TX-170 Manual de usuario

Technaxx

Technaxx TE13 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario