TechLogix Networx TL-FO-USB2-01 Manual de usuario

TL-FO-USB2-01

USB 2.0 Over Fiber Opc Extender

User Guide

Thank you for purchasing the TechLogix TL-FO-USB2-01.

Please read this guide thoroughly.

FCC Radio Frequency Interference Statement Warning

This device complies with Part 15 of the FCC rules. Operaon is subject to the following two condions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received

including interference that may cause undesired operaon.

CE Statement

We, TechLogix Networx, LLC, declare under our sole responsibility that the TechLogix TL-FO-USB2-01, to which

this declaraon relates, is in conformity with European Standard EN 55022, EN 61000 and EN 55024.

IC Statement

This Class B digital apparatus complies with Canadian ICES-003.

WEEE Statement

The European Union has established regulaons for the collecon and recycling of all waste electrical and

electronic equipment (WEEE). Implementaon of WEEE regulaons may vary slightly by individual EU member

states. Please check with your Host and state government guidelines for safe disposal and recycling or contact

your naonal WEEE recycling agency for more informaon.

Product Operaon and Storage

Please read and follow all instrucons provided with this product, and operate for intended use only.

Do not aempt to open the product casing as this may cause damage and will void warranty. Use only the power

supply provided with this product. When not in use, product should be stored in a dry locaon between -20°C

and 70°C.

Contents

Introducon..................................................................................................................................................................................... 4

TL-FO-USB2-01 Product Contents ..........................................................................................................................................4

About the TechLogix TL-FO-USB2-01......................................................................................................................................4

Device Overview............................................................................................................................................................................. 5

Host Extender ..............................................................................................................................................................................5

Client Extender ............................................................................................................................................................................ 6

Installaon Guide ........................................................................................................................................................................... 7

Example Applicaon ...................................................................................................................................................................7

Fiber Opc Link Cabling .............................................................................................................................................................7

Installing the TL-FO-USB2-01 System .....................................................................................................................................7

Installing the Host Extender.......................................................................................................................................................7

Installing the Client Extender.....................................................................................................................................................7

Connecng the Host Extender to the Client Extender...........................................................................................................8

With Surface Cabling ....................................................................................................................................................... 8

With Premise Cabling....................................................................................................................................................... 8

Checking the Installaon............................................................................................................................................................8

Connecng a USB Device...........................................................................................................................................................8

Check if the USB Device Is Detected by Your Operang System.......................................................................... 9

Compability................................................................................................................................................................................9

USB Extender Mounng.......................................................................................................................................................... 10

Troubleshoong ............................................................................................................................................................................11

Specicaons ................................................................................................................................................................................ 13

Technical Glossary........................................................................................................................................................................ 14

USB Cables ................................................................................................................................................................................ 14

Duplex LC Crossover ................................................................................................................................................................ 14

Introducon

This guide provides product informaon for the TL-FO-USB2-01, installaon instrucons, and troubleshoong

guidelines.

The instrucons in this guide assume a general knowledge of computer installaon procedures, familiarity with

cabling requirements, and some understanding of USB devices.

Your TL-FO-USB2-01 is packaged with:

• Host Extender

• Client Extender

• Locking AC power adapter

• USB 2.0 cable

The TL-FO-USB2-01 includes the ExtremeUSB® suite of features:

• Transparent USB extension

• True plug and play; no soware drivers required

• Works with all major operang systems: Windows®, OS X®, and Linux®

The TL-FO-USB2-01 incorporates Icron’s patented ExtremeUSB® technology, enabling users to extend beyond

the standard 5m cable limit for USB peripheral devices. With the TL-FO-USB2-01, USB devices can be located up

to 500 meters from the computer. This extender system is composed of two individual units: the Host Extender

unit and the Client Extender unit.

TL-FO-USB2-01 Product Contents

About the TechLogix TL-FO-USB2-01

NOTE: Notes provide addional informaon that could be useful.

CAUTION: Cauons provide important informaon about an operaonal requirement.

CAUTION: The TL-FO-USB2-01 supports only USB 3.0 devices. USB 2.0 and 1.1 devices will not

funcon with this extender.

Device Overview

Host Extender

1 2 3 4

5 6

Front

Rear

Item Type Descripon

1 Power LED (Blue) LED turns on when power is supplied. The LED light is o when no power is sup-

plied.

2 Link LED (Green) Indicates a valid ExtremeUSB® link is established between the local and remote

extenders.

3 Host LED (Green) Indicates that the RG2224 system is properly enumerated on the host computer.

LED blinks when in suspend state.

4 Acvity LED (Amber)

Indicates acvity when data transmission is acve between the local and remote

extenders. LED blinks intermiently with or without a USB device connected.

When the local and remote extenders are in suspend mode, the LED is o.

5 Power Port (oponal)

Not required in normal operaon. An oponal 5V power supply can be connected

to the local extender to provide power if the USB port on the host computer is not

capable of delivering 500mA to the unit.

6 USB Type B connector Used to connect the local extender to the host computer.

7 Link Port (Duplex LC) Extension link Duplex LC ber opc transceiver port.

Client Extender

Rear

21 111 3 4 5

Front

Item Type Descripon

1 Device Port (USB Type A) Accepts USB device(s).

2Device LED (Green/Orange)

Indicates when a USB device is connected to the Device Port. Solid green when

device is plugged in and acve. O when device is in suspend mode or remote

extender is powered o. Orange when the remote extender detects an overcurrent

condion, and the aached USB device aempts to draw more than the 500mA

current.

3 Power LED (Blue) LED turns on when power is supplied. O when no power is supplied.

4 Link LED (Green) Indicates a valid ExtremeUSB® link is established between the local and remote

extenders.

5 Host LED (Green) Indicates that the RG2224 system is properly enumerated on the host computer.

LED blinks when in suspend mode.

6 Acvity LED (Amber)

Indicates acvity when data transmission is acve between the local and remote

extenders. LED blinks intermiently with or without a USB device connected.

When the local and remote extenders are in suspend mode, the LED is o.

7 Power Port Connects to the AC power supply. Required on REX for proper operaon.

8Link Port (Duplex LC) Extension link Duplex LC ber opc transceiver port.

Installaon Guide

Example Applicaon

Fiber Opc Link Cabling

Installing the Host Extender

Installing the Client Extender

Installing the TL-FO-USB2-01 System

Local Extender

Computer

All USB 2.0 and 1.1 Devices

Up to 500m between extenders over multimode fiber optics

Remote Extender

The host and client extenders are interconnected by up to 500 meters of ber opc cabling. Two strands of

50/125μm (500m) MMF or 62.5/125μm (275m) MMF cabling are required. The cabling subsystem must provide

a duplex connecon with crossover, and must be terminated with Duplex LC connectors at both ends.

1. Place the host extender near the computer.

2. Install the supplied USB cable between the host extender and USB port on the host computer.

1. Place the client extender near the USB device(s).

2. Plug the power adapter into a suitable AC outlet.

3. Connect the power adapter to the client extender.

Before you can install the TL-FO-USB2-01, you need to prepare your site:

1. Determine where the computer is to be located and set up the computer.

2. Determine where you want to locate the USB device(s).

3. If you are using surface cabling, the TL-FO-USB2-01 supports a maximum distance of 500m.

If you are using premise cabling, ensure compable ber opc cabling is installed between the two locaons,

with ber opc informaon outlets located near both the computer and the USB device(s), and the total length

including patch cords is no more than 500m over MMF.

Connecng the Host Extender to the Client Extender

Checking the Installaon

Connecng a USB Device

With Surface Cabling

With Premise Cabling

1. Plug one end of the ber opc cabling (not included) into the Link port on the host extender.

2. Plug the other end of the ber opc cabling into the Link port on the client extender.

1. Plug one end of a ber opc patch cord (not included) into the Link port on the host extender.

2. Plug the other end of the patch cord into the ber opc informaon outlet near the host computer.

3. Plug one end of the second ber opc patch cord (not included) into the Link port on the client extender.

4. Plug the other end of the second patch cord into the ber opc informaon outlet near the USB device.

1. On the host and client extenders, check that the Power, Host, and Link LEDs are on and that the Acvity LED

is blinking. If the Link LED is permanently o, then the cabling between the host and client extedners is not

installed properly or is defecve.

2. For Windows users (2000, XP, Vista, Windows 7, Windows 8), open Device Manager to conrm that the TL-

FO-USB2-01 has installed correctly. Expand the entry for Universal Serial Bus controllers by clicking the “+”

sign. If the TL-FO-USB2-01 has been installed correctly, you should nd it listed as a “Generic USB Hub”.

3. For Mac OS X users, open the System Proler to conrm that the TL-FO-USB2-01 has installed correctly. In

the le hand column under Hardware, select “USB” and inspect the right hand panel. If the TL-FO-USB2-01

has been installed correctly, you should nd it listed as a “Hub” under the USB High-Speed Bus/USB Bus.

4. If the TL-FO-USB2-01 is not detected correctly or fails to detect, please consult the Troubleshoong secon

in this User Guide.

1. Install any soware required to operate the USB device(s). Refer to the documentaon for the USB device(s),

as required.

2. Connect the USB device to the device port on the remote extender.

3. Check that the device is detected and installed properly in the operang system.

To ensure proper operaon, the maximum length of the ber opc cable, including patch cords, must not exceed

500 meters. The cabling must provide a duplex connecon with crossover and must be terminated with Duplex

LC connectors at both ends.

Compability

Check if the USB Device Is Detected by Your Operang System

The TL-FO-USB2-01 complies with USB 1.1 and USB 2.0 specicaons governing the design of USB devices.

However, it is not possible to guarantee that all USB devices are compable with the TL-FO-USB2-01, as there

are a number of dierent conguraons that may impact the operaon of USB devices over extended distances.

To open System Proler in Mac OS X:

Open the Finder, select Applicaons, then open the Ulies folder and double click on the System Proler icon.

To open Device Manager in Windows 2000 or Windows XP:

Right click “My Computer” then select: Properes >> Hardware tab >> Device Manager

To open Device Manager in Windows Vista or Windows 7:

Open the Start menu, right click on “Computer” then select: Manage >> Device Manager

To open Device Manager in Windows 8 or Windows 10:

Right click on the lower le boom corner of your screen, then select: Device Manager

USB Extender Mounng

The boom of the TL-FO-USB2-01 enclosures features four pre-drilled holes for oponal surface mounng.

To ensure the stencil below prints to scale be sure to set the page scaling seng to “none”.

Distance between the enclosure mounng holes: 42.0 mm x 77.0 mm

1. Mark the center point of each of the four holes on your mounng surface either by directly measuring or using

a print out of the stencil below.

2. Hardware recommendaon: M3.0 locking washers and M3.0 screws (4 of each per extender) nong screw

length will depend upon thickness of mounng surface.

3. Drill through each of the four hole markings on the mounng surface using a 4.7625mm (3/16”) drill bit.

4. Align the boom enclosure holes to the newly drilled out holes on the mounng surface.

5. Place a locking washer on each of the four screws and using a screwdriver, fasten the extender into place.

mounting hole

42 mm

(1.65 in)

4.76 mm

(0.1875 in) 77 mm

(3.03 in)

Tabla de contenidos

Otros manuales de Extensor de TechLogix Networx

TechLogix Networx

TechLogix Networx TL-TP70-HDIR Manual de usuario

TechLogix Networx

TechLogix Networx TL-FO2-VLC Manual de usuario

TechLogix Networx

TechLogix Networx TL-FO2-HDC Manual de usuario

TechLogix Networx

TechLogix Networx TL-FO2-HDC2 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario