TECHLIGHTING Vance 700FMVNC13 Manual de usuario

1.0

Installation Instructions for

Vance and Lance 13 Flush Mount

700FMVNC13, 700FMLNC13

920FMVANLANS

CAUTION RISK OF FIRE-

This product must be installed in accordance with

the applicable installation code by a person familiar

with the construction and operation of the product

and the hazards involved.

Use minimum 90°c supply conductors.

CEILING COLLECTION

GP I :ENERAL RODUCT NFORMATION

These fixtures are intended to be installed

utilizing compliant junction boxes.NEC

This product is suitable for damp locations.

This product can be dimmed with a low-voltage electronic

dimmer.

This instruction shows a typical installation.

Ground the fixture in accordance with local electrical

codes.

Connect the black fixture wire to the hot power line

wire with a wire nut.

Connect the white fixture wire to the neutral power line

wire with a wire nut.

Install the fixture

Align the through holes in the fixture base with the #8-

32 screws to junction box.

Firmly tighten the #8-32 screws to hold the fixture base

in place through the next steps.

1B1B

Note: depending on the dimensions of the J-box, you

may use either the inner or outer through holes.

FIXTURE

BASE

#8-32

SCREW

FIXTURE

BASE

7400 Linder Ave, Skokie, 60077IL

847.410.4400

www.techlighting.com

a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right

to change specifications for product improvements without notification.

A Generation Brands Company

SAVE THESE INSTRUCTIONS!

Attach the trim accessories to the rim of the shade.

Imbedded magnets will allow the accessories to snap

into place.

TRIM ACCESSORY

Install the Trim Accessories(Lance only)

NOTE: The Lance 13 ships with three trim accessories.

The trim accessories are not included with the Vance.

Install the Shade

Align the pegs on the shade with the keyed slots on the

fixture base, push the shade up evenly, making sure it

sits flush on all sides.

Carefully rotate the shade into position.

SLOT

SHADE PEG

FIXTURE BASE

CAUTION: Improperly aligning the pegs before

rotating the shade into place may cause damage to

slots. Make sure the shade sits flush before rotating.

THUMB SCREW FIXTURE BASE

Locate the small threaded hole on the top side of the

shade.

Screw the thumb screw into the shade to secure it in

place.

SHADE

Este manual sirve para los siguientes modelos

Otros manuales de Luminaria de TECHLIGHTING

TECHLIGHTING

TECHLIGHTING MonoPoint 4 Manual de servicio

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario