Teac VRDS-701 Manual de uso y cuidado

1

ZFirmware update manual

Continued on the next page e

Models covered

VRDS-701, VRDS-701T

Supported operating systems

Windows 7 (32/64-bit)

Windows 8 (32/64-bit)

Windows 8.1 (32/64-bit)

Windows 10 (32/64-bit)

Windows 11

As of April, 2023

Checking the firmware version

1 Turn the unit on.

2 Press the MENU button to open the menu

screen.

3 Turn the skip knob (.//) to show the

rmware version (VERSION INFO).

Display example

MENU

VERSION INFO

SYSTEM 1.00

The number shown to the right of “SYSTEM” is the firmware

version.

Update procedures

A USB type-C cable is necessary to update the firmware. Either USB

type-A or type-C port can be used on the computer. Use a commer-

cially-available cable with a connector that fits into a USB port on

the computer you are using.

ATTENTION

Cables designed only for charging cannot be used. Use a USB

type-C cable that supports data transmission.

NOTE

The screens used in these instructions are from Windows10.

1 Uncompress the downloaded le.

The following files will appear.

oWin_DFU_driver.exe

oVRDS-701_updater_xxxx.exe (xxxx is the firmware version)

2 Double-click Win_DFU_driver.exe, and press

the Enter key.

NOTE

If a “User Account Control” pop-up message appears during

installation, click “Yes”.

3 When the Device Driver Installation Wizard

appears, click “Next”.

Microsoft and Windows are either registered trademarks or trade-

marks of Microsoft Corporation in the United States and/or other

countries.

Other company names and product names in this document are

the trademarks or registered trademarks of their respective owners.

ZFirmware update manual

20423 MA-3719A

4 Click “Finish”.

5 While pressing and holding the skip knob

(.//), set the unit’s STANDBY/ON switch

to ON.

MENU

F/W UPDATE

SYSTEM UPDATE?

6 When “F/W UPDATE” appears, turn the skip

knob (.//) to show SYSTEM UPDATE.

Then, press the skip knob (.//).

UPDATE F/W ! !

DON’T POWER OFF!

If the screen shown above does not appear, set the unit’s

STANDBY/ON switch to STANDBY, and repeat step 5.

7 Connect the USB port on the back of this unit

to the computer using a USB type-C cable.

Refer to the unit’s operation manual for the location of the USB

port.

VRDS-701: USB port

VRDS-701t: UPDATE (maintenance) port

Connect a USB type-C cable.

8 Double-click VRDS-701_updater_xxxx.exe,

and click OK.

NOTE

The following screen will appear if the unit is not recognized by

the computer. Click OK to close the window.

Check the connection between the computer and the unit,

and double-click VRDS-701_updater_xxxx.exe.

oCables designed only for charging cannot be used for

firmware updates. Use a USB cable that supports data

transmission.

oConnecting to a different USB port on the computer might

allow it to recognize the unit.

9 When “Update completed!” appears, click OK

to close the window.

10

Set the unit’s STANDBY/ON switch to STANDBY.

Follow the procedures in “Checking the firmware version” on

the previous page and check the firmware version.

Otros manuales para VRDS-701

1

Este manual sirve para los siguientes modelos

1

Otros manuales de Reproductor de CD de Teac

Manuales populares de Reproductor de CD de otras marcas

RCA

RCA RP-7923 Manual de usuario

Pioneer

Pioneer DEH-P3550MP XM Manual de usuario

Philips

Philips AZ1207 Manual de usuario

Philips

Philips CD582 Manual de usuario

Philips

Philips AZ 6821 Manual de usuario

Lasonic

Lasonic MSU-2020 Manual de usuario

THOMSON

THOMSON RCD150 Manual de usuario

Denon

Denon DCD-1420 Manual de usuario

Panasonic

Panasonic SJ-MR100 Manual de usuario

Onkyo

Onkyo DX-7210 Manual de usuario

Sony

Sony MZ-R3 Manual de usuario

Denon

Denon DVM-4800 Manual de usuario

JBL

JBL MR-32 Manual de usuario

RCA

RCA RCD152 Manual de usuario

Technics

Technics SL-PS770A Manual de usuario

Clarion

Clarion compact disc Manual de usuario

Sony

Sony MZ-M10 Manual de usuario

Philips

Philips Expanium AZ 1538 Manual de usuario