TE Connectivity 825508-5 Manual de usuario

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 2

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com LOC B

408-2746

Hand Crimping Tool 825508-5 24 JAN 12 Rev A

1. INTRODUCTION

This tool, shown in Figure 1, is used to crimp:

•PIDG* terminals and butt splices on stranded

copper wire sizes 22-10 AWG

•PLASTI-GRIP* terminals and butt splices on solid

or stranded copper wire sizes 22-10 AWG

2. CUT WIRE

Insert wire in cutter, close handles briskly.

3. GAGE WIRE

Determine wire size by inserting unstripped wire into

the smallest color-coded gage ring that will accept the

wire. See Figure 2. After stripping, use the adjacent

crimp closure to crimp terminal or splice on wire.

4. STRIP WIRE

Partially open handles and insert wire in correct notch

of wire stripping blades. End of wire must butt against

strip length locator (controls strip length). See

Figure 3. Close handles fully and rotate tool part way

around the wire. Pull wire from tool.

Be sure there are no cut or missing conductor

strands.

5. COLOR CODE

Select the correct color-coded terminal or splice for

the wire size being used:

•Red = AWG 22-16 (0.25-1.5 mm²)

•Blue = AWG 16-14 (1.5-2.5 mm²)

•Yellow = AWG 12-10 (4-6 mm²)

6. CRIMP TERMINAL OR SPLICE

(a) Insert color-coded terminal or splice in crimp

closure adjacent to the matching color-coded wire

gage ring.

(b) Position terminal or splice in crimp closure as

shown in Figure 4 or 5.

firmly in die closure.

(d) Insert stripped wire into terminal until end of

conductor is at least flush with or extended slightly

beyond end of terminal wire barrel.

Insert stripped wire into splice until end of conductor

butts against splice wire stop.

Do not use wires with nicked or missing conductor

strands.

(e) Close handles fully, then open handles by

depressing release lever.

(f) To crimp other half of splice, remove it and

reposition uncrimped half in tool as shown in Figure 5.

Follow same procedure used to crimp first half of

splice. If splice cannot be turned, turn tool around.

(g) Refer to Figure 6 for terminal or splice crimp

inspection procedure.

Figure 1

Figure 2

Figure 3

Figure 4

CAUTION

Strip Length Locator Crimp Closures Wire

Cutter

Release Lever WireStripping

Blades Color-Coded

Wire Gage

Rings

GageWireandUseAdjacent Crimp Closure

UseCorrect

Size Notch EndofWireButtsAgainst

Strip Length Locator

PLASTI-GRIP

Terminal

EndofInsulationBarrelis

Flush with Sides of Dies

PIDG

Terminal

“B” = Wire Barrel

“C” = Insulation Barrel

“B”

“C”

ORIGINAL INSTRUCTIONS

408-2746

2of 2

Rev A

7. REVISION SUMMARY

•Removed “AMPLIVERSAL” in title

Figure 5

Figure 6

Butt Splices

“B” “B”

“C”

“C” PIDG PLASTI-GRIP

“B” = Wire Barrel

“C” = Insulation Barrel

Wire Stop Wire Stop

EndofInsulationBarrelis

Flush with Sides of Dies

End of Insulation

Barrel is Flush

with Sides of Dies

Tabla de contenidos

Otros manuales de Herramientas de crimpado de TE Connectivity

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity SDE-SA PN 2063534-1 Manual de usuario

TE Connectivity

TE Connectivity AT-65 Manual de usuario

TE Connectivity

TE Connectivity 69069 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 46447 Manual de usuario

TE Connectivity

TE Connectivity 539 726-2 Manual de usuario

TE Connectivity

TE Connectivity FFC-MQS Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 543344- 1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 539682-2 Manual de usuario

TE Connectivity

TE Connectivity 2390075-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 90260-1 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 539 664-2 Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 0-1579001-3 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 539 723-2 Manual de usuario

TE Connectivity

TE Connectivity AT-SC Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario