TC Electronic M-ONE Manual de usuario

M•ONE &

M•ONE XL

DUAL EFFECTS PROCESSORS

UUSSEERR’’SSMMAANNUUAALL

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings.

Install in accordance with the

manufacturer's instructions.

8 Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding

prong. The wide blade or the third prong

are provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10 Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories

specified by the manufacturer.

12 Unplug this apparatus during lightning

storms or when unused for long periods of

time.

13 Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or has

been dropped.

• This equipment should be installed near the

socket outlet and disconnection of the

device should be easily accessible.

• Do not install in a confined space.

• Do not open the unit - risk of electric shock

inside.

Caution:

You are cautioned that any change or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

Service

• There are no user-serviceable parts inside.

• All service must be performed by qualified

personnel.

Warning!

• To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

• This apparatus must be earthed.

• Use a three wire grounding type line cord

like the one supplied with the product.

• Be advised that different operating voltages

require the use of different types of line

cord and attachment plugs.

• Check the voltage in your area and use the

correct type. See table below:

Voltage Line plug according to standard

110-125V UL817 and CSA C22.2 no 42.

220-230V CEE 7 page VII, SR section

107-2-D1/IEC 83 page C4.

240V BS 1363 of 1984.

Specification for 13A fused

plugs and switched and

unswitched socket outlets.

The lightning flash with an arrowhead

symbol within an equilateral triangle, is

intended to alert the user to the

presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in the literature accompanying the

product.

IMPORTANT SAFETY INSTRUCTIONS

Certificate Of Conformity

TC Electronic A/S, Sindalsvej 34, 8240

Risskov, Denmark, hereby declares on own

responsibility that following products:

M•ONE - Dual Effects Processor &

M•ONE XL - Dual Effects Processor

- that is covered by this certificate and

marked with CE-label conforms with

following standards:

EN 60065 Safety requirements for mains

(IEC 60065) operated electronic and

related apparatus for household

and similar general use

EN 55103-1 Product family standard for

audio,video, audio-visual and

entertainment lighting control

apparatus for professional

use. Part 1: Emission.

EN 55103-2 Product family standard for

audio, video, audio-visual and

entertainment lighting control

apparatus for professional

use. Part 2: Immunity.

With reference to regulations in following

directives:

73/23/EEC, 89/336/EEC

Issued in Risskov, 09 2001

Anders Fauerskov

Chief Executive Officer

EMC / EMI.

This equipment has been tested and found to

comply with the limits for a Class B Digital

device, pursuant to part 15 of the FCC rules.

These limits are designed to provide

reasonable protection against harmful

interference in residential installations. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on. The user is

encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

For the customers in Canada:

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

TABLE OF CONTENTS

INTRODUCTION

Important Safety Instructions

Table of contents . . . . . . . . . . . . . . . .3

Introduction . . . . . . . . . . . . . . . . . . . . .5

Front Panel . . . . . . . . . . . . . . . . . . . . .6

Rear Panel . . . . . . . . . . . . . . . . . . . . .8

Signal flow diagram &

Soldering Instructions . . . . . . . . . . . . .9

BASIC OPERATION

The M•ONE Display . . . . . . . . . . . . .10

I/O Setup . . . . . . . . . . . . . . . . . . . . .11

Clock Mismatch . . . . . . . . . . . . . . . . .11

Utility & MIDI . . . . . . . . . . . . . . . . . . .12

Routings . . . . . . . . . . . . . . . . . . . . . .13

Recall . . . . . . . . . . . . . . . . . . . . . . . .16

Edit . . . . . . . . . . . . . . . . . . . . . . . . . .16

Store . . . . . . . . . . . . . . . . . . . . . . . . .17

Tap . . . . . . . . . . . . . . . . . . . . . . . . .17

ALGORITHMS

Reverb

Hall . . . . . . . . . . . . . . . . . . . . . . . . . .18

Room . . . . . . . . . . . . . . . . . . . . . . . .19

Small Room . . . . . . . . . . . . . . . . . . .21

Plate 1 . . . . . . . . . . . . . . . . . . . . . . .22

Plate 2 . . . . . . . . . . . . . . . . . . . . . . .23

Spring . . . . . . . . . . . . . . . . . . . . . . . .24

Live . . . . . . . . . . . . . . . . . . . . . . . . .25

Ambience . . . . . . . . . . . . . . . . . . . . .26

Other Algorithms

Delay - One Tap & two Tap . . . . . . . .27

Delay - PingPong . . . . . . . . . . . . . . .28

Chorus - Classic & 4-Voice . . . . . . . .29

Flange - Classic & 4-Voice . . . . . . . .30

Pitch - Detune & Pitch Shift . . . . . . . .31

Parametric Equalizer . . . . . . . . . . . . .32

Compressor & Limiter . . . . . . . . . . . .33

Gate/Expander . . . . . . . . . . . . . . . . .34

De-esser . . . . . . . . . . . . . . . . . . . . . .35

Tremolo - Hard & Soft . . . . . . . . . . . .36

Phaser - Vintage & Smooth . . . . . . . .37

APPENDIX

MIDI Implementation Chart . . . . . . . .38

Technical Specifications . . . . . . . . . .39

Troubleshooting . . . . . . . . . . . . . . . .41

Preset List . . . . . . . . . . . . . . . . . . . .42

TC Electronic, Sindalsvej 34, DK-8240 Risskov - [email protected] English version

Prod. No: E60500152

Rev 4 - SW - V 1.43 - ST

Rev 4 - SW - V 2.07 - XL

INTRODUCTION

Congratulations on the purchase of your new TC Electronic M•ONE or M•ONE XL unit.

The M•ONE is a Dual Engine Multi-effects Processor, focusing mainly on high quality Reverbs. The

M•ONE can be used for a number of purposes due to flexible routing of the two Engines and more

than 20 TC algorithms. Do you want two independent Reverbs, controlled from separate Auxiliary

sends? Select the Dual Input Routing plus two Reverbs, and you are up and running. Do you want

a compressor in front of a Delay? Select the Serial Routing, a Compressor and a Delay. You can

even tap the Delay time on the TAP key. Or maybe you just want stick with that one Routing, no

matter the preset? Simply use the Routing Lock function to avoid routing changes at preset change.

It is really as easy as that, go ahead and tweak some keys and knobs. We hope you have as much

pleasure using the M•ONE as we had making it.

Please note that this manual covers both the M•One and the M•One XL. Both products will in

general be referred to as “M•One”. When a feature relevant only for the XL version is

covered, this will be marked with “XL only”.

• Hall

• Room

• Small Room

(XL only)

• Plates 1&2

• Spring

• Live

• Ambience

• Delay One Tap

• Delay Two Tap

• PingPong Delay

(XL only)

• Chorus Classic & 4-voice

• Flange: Classic & 4-voice

• Pitch: Detune & Pitch Shift

• Parametric EQ

• Compressor/Limiter

• Gate/Expander

• De-esser

• Tremolo

• Phaser

Though the M•ONE is focusing on high quality Reverb you will discover that the

M•ONE also covers a wide variety of other algorithms. Experience and enjoy !

FRONT PANEL

POWER button

Power on/off.

IN LEVEL knob

Adjusts the Input level.

At center position a relay will

switch the Input circuit

between consumer and pro

level. This will insure optimal

Input gain range and superb

“signal to noise” ratio is

achieved.

MIX knob

Adjusts the global mix between

dry and wet signal.

Fully clockwise is 100% effect.

EFFECT BAL knob

Adjusts the balance between

the two Engines.

INPUT Meters

The Peak meter shows the

Input level of left/right

channels.

The meter range is:

0, -3, -6 ,-12, -18, -24, -40.

OVERLOAD LEDs

The OVERLOAD LEDs

indicate one of two situations:

• The Input level is too hot

and therefore overloading.

• There is an internal DSP

overflow.

The Overload LED is lit when

1 sample is @ -1dBFS.

INPUT - Analog/Digital

Indicates whether the M•ONE

is set to analog or digital Input.

When set to digital Input, the

Sample Rate automatically

switches to DI.

In case of no or unacceptable

clock the "Digital" and "DI" icon

will be blinking.

ANALOG/DIGITAL LED

ANALOG/DIGITAL indicator

states the selected Input.

Input type is selected in the

"I/O Setup" menu.

SAMPLE RATE indicator

The SAMPLE RATE indicator

shows the clock source and

the incoming master clock.

The “Digital In” icon will be

blinking if no clock or

unacceptable clock is found.

ROUTING indicator

Indication of what Routing

mode the M•ONE currently is

using.

ALGO Indicator

Shows the currently used

algorithms in each of the two

Engines.

DYNAMIC meters 1+2

These two meters show the

gain reduction when an Engine

is running Dynamic algorithms.

The Dynamic algorithms are:

Compressor, Limiter, Gate,

Expander and De-esser.

DISPLAY

Displays the preset number

and the preset type:

Factory or User.

EDITED icon

This icon will be lit as soon as

the current recalled preset has

been modified.

FACTORY/USER icon

Shows whether you are

operating in the Factory or the

User bank.

MIDI IN icon

Shows any incoming

MIDI activity.

FRONT PANEL

ROUTING key

Press the ROUTING key to set

the Engine Routing.

The options are: Dual Send/

Ret, Parallel, Parallel/Serial,

Serial, Stereo, Dual Mono.

I/O SETUP

Basic parameters are set here.

• Input source - Analog/Digital.

• Sample Rate -

44.1/48kHz/DI

• Bypass Mode - See Bypass

keys 1 and 2.

• Global Output level.

• Dither 16, 20 or 24(off).

TAP key

Tap this key to enter the global

Tap tempo and to enter the

Tap menu. Subdivision of the

tapped tempo is setup in this

menu. The tapped tempo can

be used for Delay time, Chorus

rate etc.

UTILITY

MIDI, Sys-Ex ID, Routing-lock,

Bypass mode, Pedal function

and Display View angle.

ALGO/EDIT 1+2

Press this key to enter the Edit

display and the Algorithm

Change display of the currently

selected Engine.

BYPASS keys 1 and 2

The Bypass mode is set up in

Utility. There are three different

Bypass modes:

10% Mix:

The Input signal is passed

directly to the Output.

2FX Input:

Cuts only the Engine Input

in order to let the effect "ring

out", but will still leave the

same amount of dry signal

coming through.

3FX Output:

Cuts only the Engine Output

in order to kill the FX instan-

taneously, but leaves the

same amount of dry signal

coming through.

RECALL key

Selects the Recall menu.

Select a desired preset using

the CONTROL wheel and

press the ENTER key to

enter/load the selected preset.

STORE key

Selects the Store menu.

Presets can be stored in the

User bank only. Location is

selected using the CONTROL

wheel. Operation is confirmed

using ENTER.

CURSOR UP/DOWN

Use the cursors to move

around in the display.

ENTER key

Confirms operations. The

ENTER key LED will indicate

when this key can be used.

EXIT key

Is used to exit a menu or to

disapprove an action.

CONTROL wheel

Is used to change values.

REAR PANEL

UL6500

EN/IEC 60065

PROFESSIONAL AUDIO EQUIPMENT

THRU

INLEFT LEFTRIGHT RIGHT OUT

MIDIBALANCED INPUTS BALANCED OUTPUTS DIGITAL I/O PEDAL

S/PDIF

SERIAL NO.

TYPE: MAN001

TC ELECTRONIC

MADE IN THAILAND

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK DO NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE

AVIS:

RISQUE DE CHOC ELECTRIQUE-NE PAS

OUVRIR.

100-240VAC

50-60Hz, 15W

CAUTION

CUS

THIS CLASS B DIGITAL DEVICE MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-

CAUSING EQUIPMENT REGULATIONS AND COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION SUBJECT TO CONDITIONS STATED IN THE MANUAL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Balanced

Jack

Analog

Inputs

Balanced

Jack

Analog

Outputs

Pedal Input

for Bypass

MIDI

In, Out, Thru

Digital

S/PDIF

Input/

Output

Serial no.Power

Input

Use Left Input

for mono only

Balanced

XLR

Analog

Inputs

Balanced

XLR

Analog

Outputs

Pedal Input

for Bypass

MIDI

In, Out, Thru

Digital

S/PDIF

Input/

Output

Serial no.Power

Input

M•One “Standard”

M•One XL

Use Left Input for mono only.

Input select MUST be set to

ANLGLEFT in the I/O menu.

Otros manuales para M-ONE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de grabación de TC Electronic

TC Electronic

TC Electronic Impact Twin Manual de usuario

TC Electronic

TC Electronic D-TWO Manual de usuario

TC Electronic

TC Electronic INTONATOR Manual de usuario

TC Electronic

TC Electronic Konnekt Live Manual de usuario

TC Electronic

TC Electronic Multi-effects Processor G-Natural Manual de usuario

TC Electronic

TC Electronic Konnekt 24D Manual de usuario

TC Electronic

TC Electronic TC2290 Manual de usuario

TC Electronic

TC Electronic DBMAX - V 2 Manual de usuario

TC Electronic

TC Electronic Rusty Fuzz Manual de usuario

TC Electronic

TC Electronic G-Force Manual de usuario

TC Electronic

TC Electronic DVR250 NATIVE Manual de usuario

TC Electronic

TC Electronic SYSTEM 6000 MKII Manual de usuario

TC Electronic

TC Electronic M-ONE Manual de usuario

TC Electronic

TC Electronic Desktop Konnekt 6 Manual de usuario

TC Electronic

TC Electronic C400XL Manual de usuario

TC Electronic

TC Electronic D22 Manual de usuario

TC Electronic

TC Electronic Konnekt 24D Manual de usuario

TC Electronic

TC Electronic M100 Manual de usuario

TC Electronic

TC Electronic Studio Konnekt 48 Manual de usuario

TC Electronic

TC Electronic FireworX Manual de usuario

TC Electronic

TC Electronic G-Major Manual de usuario

TC Electronic

TC Electronic FirewarX Manual de usuario

TC Electronic

TC Electronic Natural Manual de usuario

TC Electronic

TC Electronic Nova Dynamics NDY-1 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado