TASKING ISYSTEM iC5000 Instrucciones de uso

iC5000 BlueBox

Hardware User Manual

V1.8, November 2023

isystem.com/start

General safety instructions

Please read the following safety precautions carefully before putting this device to use to avoid

any personal injuries, damage to the instrument, or to the target system. Use this instrument

only for its intended purpose as specified by this manual to prevent potential hazards.

Use included power cord and power supply

The enclosed power supply has been approved for use by iSYSTEM. Please contact iSYSTEM if

you need to consider an alternative power.

Use grounding wire

Prior to applying power to either the BlueBox or the target, connect the device and the target sys-

tem together with the included grounding wire. This is to avoid potential damage caused by any

voltage difference between the device and the target system.

Use proper overvoltage protection

Ensure proper protection to avoid exposing the BlueBox device or the operator to overvoltage

surges (e.g. caused by thunderstorm, mains power).

Do not operate without cover

Do not operate the device with cover removed.

Avoid circuit and wire exposure

Do not touch exposed components or wires when the device is powered.

Do not operate with suspected damage

If you suspect damage may have occurred, the BlueBox device must be inspected by qualified

service personnel before further operation.

Do not operate the device outside its rated supply voltage or environ-

mental range

Consult with iSYSTEM before using equipment outside of the parameters provided in this

manual.

This symbol is used within the manual to highlight further safety notices.

Contents

Package content ................................................................................................................................ 4

Specifications ....................................................................................................................................... 5

Device description ............................................................................................................................. 6

Hardware Setup and Configuration ........................................................................................ 9

Accessories ......................................................................................................................................... 10

Declarations ....................................................................................................................................... 11

Package content

iC5000 BlueBox On-Chip Analyzer is a hardware and software platform designed for debugging

and testing a wide range of embedded microcontroller platforms that are based on a variety of

processor architectures. Functionality can be further extended with the addition of the I/O Mod-

ule, enabling the synchronous capture of analog and digital signals in parallel to trace informa-

tion. Such capability is used for advanced debugging of complex applications together with our

winIDEA Integrated Development Environment (IDE), as well as for thorough testing in conjunc-

tion with our testing environment testIDEA. Complementing the hardware is a range of software

which target three key areas of embedded development: debugging, timing-analysis and testing.

The standard iC5000 order is delivered with the following components:

iC5000 Base Unit including

pre-assembled DTM module

25 cm 40-pin ribbon cable

Power supply

Ordering code:

IC50000 + IC50020

Ordering code:

IC50020-25

Ordering code:

IC30000-PS

USB 2.0 cable

Ethernet cable

Grounding wire

Ordering code:

BB-USB20-180

Ordering code:

BB-ETHCAT5-200

Ordering code:

BB-WIRE

Specifications

GENERAL

Operating temperature

10°C to 40°C

Storage temperature

-10°C to 60°C

Humidity

5% to 80% RH

MECHANICAL

Size

122 x 127 x 45 mm (W x D x H)

Weight

approx. 500g

OPERATION

Communication inter-

faces to PC

USB 2.0, 10/100 Mbps Ethernet

Supply voltage

10V to 24V DC

Power consumption

< 8W

ELECTRICAL

Debug signal valid in-

put voltage range

1.8V to 5.5V DC

Debug signals

47 series termination/protection resistors, ESD protection devices.

Depending on the specific debug adapter, termination might be differ-

ent from 47 on some critical signals.

All inputs except the

TDO

10 kOhm pull-up resistor

TDO input

10 kOhm pull-down resistor

TMS and TDI debug

signals

10 kOhm pull-up resistor

RESET

1 kOhm pull-up resistor, buffer-driven to prevent current flow into an

unpowered iC5000 from a powered target board

TAR_VREF (target refer-

ence voltage) pin

100 kOhm input impedance

Device description

A – Two connectors, marked #1 and #2. These connectors are the interface to the target micro-

controller. Depending on the target microcontroller debug features, the supplied ribbon-cables

will need to be connected to either connector #1 only or connectors #1 and #2.

B – The indicator lights provide the status of the hardware:

Power Indicator

On – Powered on

Off – Powered off

R – Running Indicator

On – Target microcontroller is executing code

Off – Target microcontroller is halted

F –Free Indicator

On – BlueBox is available for a connection from a host PC

Off – Active connection to the BlueBox from a host PC exists

C – The grounding socket (GND) should be used, together with the supplied Grounding wire to

create an electrical connection between the BlueBox and the target circuitry. The socket is suit-

able for a 2 mm Multi Contact Plug (also known as a Banana Plug) if building a longer or a re-

placement cable on your own.

D– Power Switch

E – Power Supply Socket

The socket and plug are latching to stop the plug from being accidentally pulled out of the

socket. To remove the power plug from the socket, always pull gently of the sleeve of the plug

and never on the wire.

F – 10/100 Ethernet Socket

G– USB 2.0 Socket

Recommended to use the USB 2.0 cable. The USB 2.0 interface provides the highest possible

data transfer rate of the two available interfaces. Use of alternate cables must be undertaken at

your own risk.

Both the 10/100 Ethernet Socket and the USB 2.0 Socket can be connected to a network/PC sim-

ultaneously. The active interface will be determined by whichever interface winIDEA connects to

first.

When powering on the system, switch the BlueBox unit on before powering on the Tar-

get. When powering down the system, power off the Target before powering off the

BlueBox unit!

FBridge port is not Ethernet port!

Use only original accessories for powering and connecting with the BlueBox unit. Con-

sult with Technical support before attempting to use any other accessory.

Hardware Setup and Configuration

For detailed visual presentation of the hardware setup and configuration, refer to the

Getting started tutorial - use the link isystem.com/start.

1. Connect the power supply cable. BlueBox should be switched off.

2. First connect via USB. Later you can configure TCP/IP connection to work remotely.

3. Connect the Grounding wire to the BlueBox and the Target.

If the Grounding wire is not connected, the ground potential difference between the

BlueBox and the Target can exceed well over 1000V even before any of the devices are

powered up. This voltage difference is discharged over the BlueBox and the Target,

leading to the possible destruction of electronic components.

4. Connect the ribbon cable to the iC5 Debug Adapter.

5. Connect the ribbon cable to the BlueBox connector(s).

6. Connect the Debug Adapter to the Target. To disconnect squeeze the two metal latches on

the ribbon cables.

7. Power on procedure:

BlueBox

Target

8. Install winIDEA and create a new workspace.

Accessories

Various debug adapters are available to connect the iC5000 to a wide range target debug con-

nector as commonly found on microcontroller development boards.

More information about our products on www.isystem.com or via [email protected].

Tabla de contenidos

Otros manuales de Instrumento de medición de TASKING

TASKING

TASKING iSYSTEM RH850 Manual de usuario

TASKING

TASKING iSYSTEM ARM HSSTP II Manual de usuario

TASKING

TASKING iSYSTEM Infineon AGBT Manual de usuario

TASKING

TASKING iSYSTEM iC5700 CI BlueBox Instrucciones de uso

TASKING

TASKING iSYSTEM Infineon DAP Instrucciones de uso

TASKING

TASKING iSYSTEM iC5700 Manual de usuario

TASKING

TASKING iSYSTEM Aurora MPC5 Series Manual de usuario

TASKING

TASKING iSYSTEM Infineon DAP Manual de usuario

TASKING

TASKING iSYSTEM Infineon DAP/DAPE II Manual de usuario

TASKING

TASKING iSYSTEM Infineon SGBT HSTCU Manual de usuario

TASKING

TASKING iSYSTEM ARM HSSTP II Instrucciones de uso

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

TASKING iSYSTEM iC5000 Instrucciones de uso

Manuales populares de Instrumento de medición de otras marcas