Targus AMB09US Manual de usuario
User Guide
Targus Bluetooth Comfort Laser Mouse
2
Introduction
Thank you for your purchase of the Targus Bluetooth Comfort Laser
Mouse.This mouse uses Bluetooth technology which provides a seamless
connection up to 33 feet (10 m) away. This is a plug and play device so no
additional software is required. The advance scroll wheel feature program
can be downloaded from the Targus website.
System Requirements
Hardware
• Bluetooth-enabled computer
Operating System
• Microsoft Windows®2000
• Microsoft Windows®XP
• Microsoft Windows Vista®
• Microsoft Windows®7
• Mac OS®X 10.4 or later
Contents
• Targus Bluetooth Comfort Laser Mouse
• 2 x AA Batteries
• User Guide
Targus Bluetooth Comfort Laser Mouse
3
1. Remove the battery cover from the top of the mouse by using the notch
on the back. Carefully lift the cover up as shown in the diagram.
Installing the Batteries
2. Remove the battery safety clip by squeezing the center of the clip and
sliding it back, towards the rear of the mouse. Lift up and rotate the clip
out of the way.
NOTE: THE BATTERY SAFETY CLIP WILL NEED TO BE IN THE SECURE, LOCKED POSITION
BEFORE THE BATTERY COVER CAN BE PUT BACK IN PLACE.
Targus Bluetooth Comfort Laser Mouse
4
3. Slide and lift to remove the battery holder as shown.
4. Insert the two AA batteries, making sure that the positive (+) and
negative (-) ends of each battery match the polarity indicators inside
the battery compartment.
Targus Bluetooth Comfort Laser Mouse
5
6. Turn on the mouse by pressing the power On/Off button on the bottom
of the mouse. Hold for 3 seconds and then release.
5. Replace the battery safety clip and by sliding it forward until it clicks into
place and then replace the battery cover.
Power button
Targus Bluetooth Comfort Laser Mouse
6
Enable Discovery mode:
The mouse will go into pairing mode automatically after it is powered on. The 1st
and 3rd LEDs will flash alternately for 60 seconds; this indicates that the pairing
sequence is in operation. Once the connection is established, the 1st and 3rd LED
lights will light up steadily for 3 seconds.
Power On:
Press and hold the power button for 3 seconds and then release.
The battery life indicator will briefly light up showing the current power level of the
batteries.
Power Off:
Press and hold the power button for 3 seconds and then release.
The battery life indicator will briefly light up and then fade out.
Battery Check:
After the mouse is turned on, quickly press and release the power button. The
battery life indicator will light up showing the current power level of the batteries.
Initial Mouse Setup
If the connection is not established by the end of 60 seconds, the mouse will go
into sleep mode. Click on any mouse button to exit from sleep mode. The pairing
sequence will re-start automatically.
1st LED
3rd LED
Targus Bluetooth Comfort Laser Mouse
7
Battery Life Indicator
NOTE: WHEN THE FIRST LIGHT IS BLINKING, PLEASE REPLACE THE BATTERIES
3 LEDs lit Full power
2 LEDs lit Half power
1 LED lit Low power
Power Saving mode:
After an extended period of time, if the mouse is not used, it will automatically enter
power saving mode to conserve power and increase battery life. Click on any mouse
button to resume the normal operation. The mouse may take a few seconds to
reconnect with your computer.
Power Management
• To extend the life of your battery, turn off the mouse while travelling or
when you’re not using it.
Targus Bluetooth Comfort Laser Mouse
8
Initial Configuration
Before you can begin using your Bluetooth®mouse, you will first need to
perform some initial setup steps.
NOTE: PLEASE USE THE LATEST BLUETOOTH DEVICE DRIVER. INSTRUCTION SCREENS MIGHT VARY
DEPENDING ON THE VERSION OF YOUR BLUETOOTH DEVICE DRIVER.
fi
Targus Bluetooth Comfort Laser Mouse
9
Connecting with Bluetooth Software:
WIDCOMM or Microsoft (Windows XP & Windows Vista)
1. Go to the Bluetooth Places icon located on your desktop or in the system tray and
double click, then click Add a Bluetooth Device.
(Windows XP)
(Windows Vista)
2. The Bluetooth Wizard screen will prompt. Please follow the onscreen instructions.
(Windows Vista)
(Windows XP)
Targus Bluetooth Comfort Laser Mouse
10
3. Power on the mouse and it will automactically go into discovery mode. Click Next
to continue pairing and the computer will search for the mouse.
4. The confirmation window will appear after the computer finishes detecting
the Bluetooth devices. Select the Bluetooth Wireless Mouse and click Next to
continue. (There may be one or more different Bluetooth devices detected.) If the
mouse is not detected, please make sure the power is on and in discovery mode.
Press Search Again to re-pair the device.
(Windows Vista)
(Windows XP)
(Windows Vista)
(Windows XP)
Tabla de contenidos
Otros manuales de Ratón de Targus
Targus
Targus Stow-N-Go Notebook Mouse Manual de usuario
Targus
Targus Wireless Multi-Channel Mouse Manual de usuario
Targus
Targus 5-Button Laser Retractable Manual de usuario
Targus
Targus OPTICAL Manual de usuario
Targus
Targus Ultralife Manual de usuario
Targus
Targus PAWM004E Manual de usuario
Targus
Targus Optical Notebook Mouse Manual de usuario
Targus
Targus AMU06EU Manual de usuario
Targus
Targus WIRELESS COMFORT LASER MOUSE Manual de usuario
Targus
Targus Stow-N-Go Notebook Mouse Manual de usuario
Targus
Targus Optical Bluetooth Mouse Manual de usuario
Targus
Targus Wireless Mouse Manual de usuario
Targus
Targus AMW43EU Manual de usuario
Targus
Targus Wireless Laser Mouse Manual de usuario
Targus
Targus Notebook Mouse Manual de usuario
Targus
Targus W071 Manual de usuario
Targus
Targus Store-N-Go Ultra portable Laser mouse Manual de usuario
Targus
Targus AMW841 Manual de usuario
Targus
Targus AMU40US Manual de usuario
Targus
Targus Stow-N-Go Notebook Mouse Manual de usuario
