Tanning essentials Classic Guía de instalación

Australia • China • United Kingdom • USA

SIMPLY UNCOMPLICATED

TANNING SYSTEMS

Training Manual

WELCOME

Thank you for choosing the Tanning Essentials Classic Spray Tan System.

Please read the following to enjoy your new system for many happy

tanning applications.

QUICK SET UP GUIDE

The Tanning Essentials Classic Spray Tan System contains the following:

1 x Classic Spray Unit 1 x Classic Spray Applicator

1 x Classic Spray Hose 1 x Power Cord

1 x Manual

* Additional solution cups with lids can be purchased through your

dealer to conveniently change solutions and keep solution air tight.

ON/OFF SPEEDHEAT

LOW MEDHIGH

SPRAY SYSTEM

SPRAY APPLICATOR

Control Panel

(see page 5 for

more information)

Hose

Connector

Shock

Ansorbing Feet

Carry

Handle

Power

Connector

(At Rear)

Washable

Air Filter

(Underneath)

Adjustable

Spray

Nozzle

Solution Cup

Hose

Connector

Solution Knob

Trigger

Handle

SPRAY APPLICATOR

STEP 1

Unscrew solution cup and Fill Solution Cup no

more than ½ - ¾ full. Over filling the solution cup

may cause the cup to leak.

STEP 2

Insert Cup into applicator and screw tightly.

Being careful not to cross thread the solution cup

STEP 3

Set the spray pattern by turning the silver nozzle,

aligning the nozzle in a vertical position for

up/down spraying and horizontal position for left

to right spraying.

STEP 4

Adjust Solution Dial behind the trigger to desired

level. Start with the dial hard against the trigger

resulting in maximum solution spraying from the

applicator, then wind out until the desired result is

obtained.

STEP 5

Attach Hose. Insert the hose into the back of the

spray applicator until firmly in place.

SPRAY UNIT

STEP 1

Attach Hose to Unit. Insert hose into the unit with

the bayonet style fitting and turn anti-clockwise

until firmly in place. Avoid over tightening as this

may result in broken components.

STEP 2

Attach power cord and turn power on at the wall

switch.

STEP 3

Turn the unit on and start spraying. The unit is

controlled via three buttons on the front of the

Spray Unit (see below).

ON/OFF SPEED

(Low, Medium & High)

this controls the air flow

HEAT (On/Off)

The unit will heat

the air to warm.

The most common setting is Medium air flow with heat On.

ON/OFF SPEED HEAT

LOW MED HIGH

MAINTENANCE GUIDE

SPRAY APPLICATOR

Step 1 Remove hose.

Step 2 Unscrew solution cup and empty any excess solution. It is

recommended that this be done over a sink or a wet area.

Step 3 Rinse the empty solution cup with warm water.

Step 4 With warm water in the solution cup, spray the water through

the applicator. Use the highest setting for maximum water

spraying when cleaning.

Step 5 Empty solution cup and re-set the solution dial on the back

of the gun to the regular spray setting.

Step 6 Wipe any excess water from the applicator with a cloth and

warm water.

SPRAY UNIT

Step 1 Clean the Spray Unit with a cloth. Avoid using anything

abrasive. Windex and Mr. Sheen are useful products for

maintaining the gloss finish on your Spray Unit.

Step 2 Clean the filter. Remove the filter from the base of the unit

and rinse in warm water. Wait until filter is completely

dry before re-fitting. Positioning the spray unit behind the

spray technician when in use will ensure the unit stays

cleaner for longer.

TROUBLE SHOOTING

If you experience problems with this unit, in the first instance please

read carefully the relevant sections of this User Manual and this Trouble

Shooting section. If you can not solve your problem please contact your

supplier via phone for assistance.

Problem

The Spray

Unit will

not turn on

The spray

applicator

is leaking

The spray is

spluttering

Cause What to do

Power cord not attached Ensure that the power cord

is pushed in firmly to the base

of the unit and wall socket

Electricity not turned on Ensure the power point is on

The unit is not turned on Press the On/Off Button on the

control panel and watch for the

LED light to indicate ON.

Spray Cup is not tight enough Tighten the solution cup

Solution cup seal missing Insert the rubber cup seal

Too much solution Empty some solution from

the spray cup

Nozzle may be blocked Spray warm water through

the applicator

Solution cup low Add solution to the cup

Air speed is set too low Check the filter for blockages

Angled applicator too Keep the applicator on a

sharply while spraying lesser angle while spraying

Nozzle may be blocked Spray warm water through

the applicator

Filter could be blocked Ensure the filter underneath

the Spray Unit is clean

Spray applicator control Wind in solution knob below

dial is set too low the hose connecter of the gun

Problem

No solution

is coming out

of the spray

applicator

The applicator

is continuing

to spray

Hose coming

out of unit

Cause What to do

Nozzle may be blocked Spray warm water through

the applicator

Solution cup low Add solution to the cup

Trigger is jamming Spray warm water through the

applicator repeatedly ensuring

the Solution Dial is allowing

maximum water through the

applicator

Solution Dial on Wind in the solution dial

applicator set too low on applicator

Trigger or nozzle is jamming Spray warm water through the

applicator repeatedly ensuring

the Solution Dial is allowing

maximum water through the

applicator

Hose not correctly Ensure the fitting is inserted

fitted to unit and quick connect fitting is

locked into place.

Hose fitting broken Contact your supplier

from over tightening or service agent

TIPS AND TRICKS

Problem

The solution is

sitting on the

skin or beading

on the client

The client has

tanning solution

in areas they

don’t wish to

tan

The client

appears orange

The spray tan

has not

developed as

dark as desired

Cause

Too much tanning solution has

been sprayed onto the skin

Client has not prepared their

skin correctly i.e. moisturiser

or perfume on the skin

Client maybe excessively

hot and perspiring

The technician has sprayed

the area incorrectly

Client has touched part of their

body with a spray tanned area

Too much tanning solution has

been sprayed onto the skin

The client may have left a

rapid tanning solution on

too long

The client may have low

toleranceto DHA

The spray tan solution used

may be old or heat affected

reducing the reaction in the

skin. Sometimes a green hue

will appear to indicate this

A different solution was

sprayed or the spray

application dial was set lighter

The client may have showered

or perspired before the tan

could develop

Other factors may affect the

tan’s development, including

diet, hormones and medication.

Please refer to the client

What to do

Dab area gently with a clean

dry towel and re-spray lightly,

blending the tan in

Exfoliate the area using tan

removing product for best

results or a cloth and soap

Exfoliate the skin before

re-spraying and ensure the

spray application is lighter

Be sure to keep the solution

in a cool dry place and ensure

the solution is fresh.

Ensure the client has followed

the correct recommendations

for preparation and post spray

tan care.

The client can be resprayed if

required after their minimum

8 hours and after a shower has

been taken

WARRANTY INFORMATION

IMPORTANT

Please keep your proof of Purchase and User Manual in a safe place as

you will require these to make a warranty claim. Prior to making a

claim you should read through the trouble shooting section in the

manual and contact your supplier via phone. Any warranty claims

should be made directly to your supplier.

If within one (1) year from the date of purchase, the product fails due to

a defect in material or workmanship, we will repair if possible or

replace it free of charge with a comparable unit which may be new or

refurbished. This warranty applies only to the original purchaser and is

not transferable. The goods must be returned to the seller with proof of

purchase to be assessed at the purchasers cost.

Warranties shall not apply to any defect, failure or damage caused by

improper use or improper or inadequate maintenance and care. The

manufacturer shall not be obligated under these warranties:

a) to repair damage resulting from attempts by personnel other than

authorised representatives to install, repair or service the product,

b) to repair damage, malfunction, or degradation of performance result-

ing from improper use or incompatible solution,

c) to perform maintenance or cleaning or to repair damage, malfunc-

tion, or degradation of performance resulting from failure to perform

user maintenance and cleaning as prescribed,

d) to repair damage, malfunction, or degradation of performance result-

ing from use of the product in an environment not meeting the oper-

ating specifications,

To activate your warranty, please complete the information below and

post to your supplier within 14 days of purchase.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Producto de cuidado personal de tanning essentials

tanning essentials

tanning essentials Turbo Twister Manual de usuario

tanning essentials

tanning essentials Tanning Curtain Guía de instalación

tanning essentials

tanning essentials PROV Instrucciones de funcionamiento

tanning essentials

tanning essentials PROV Guía de instalación

tanning essentials

tanning essentials Pro Guía de instalación

tanning essentials

tanning essentials CORDLESS Guía de instalación

tanning essentials

tanning essentials Turbo Twister Spray Station Guía de instalación

tanning essentials

tanning essentials SPRAY STATION Guía de instalación

tanning essentials

tanning essentials TURBO TWISTER TOWER Guía de instalación

Manuales populares de Producto de cuidado personal de otras marcas

Pretika

Pretika ST102 Manual de instrucciones

Beurer

Beurer FC 76 Manual de usuario

Pebble Grey

Pebble Grey 500.40.70-75 Manual de usuario

PUSH

PUSH ortho Manual de usuario

Dermlite

Dermlite DL3N Manual de usuario

DERMAPEN

DERMAPEN SEMI Manual de usuario

HiB

HiB Spectre 50 Manual de usuario

Carex

Carex SunLite Manual de usuario

Roper Rhodes

Roper Rhodes Intense Manual de lista de piezas

Interacoustics

Interacoustics Titan IMP440 Instrucciones de funcionamiento y seguridad

ReTrak

ReTrak VS001 Manual de usuario

LED Technologies

LED Technologies dpl PAIN RELIEF Joint Wrap Manual de usuario

Casa Lusso

Casa Lusso MVL1000x450PR Manual de usuario

Quoizel

Quoizel QR3326 Instrucciones de montaje

Beurer

Beurer EM 37 Manual de usuario

BERTSCHAT

BERTSCHAT HEATED HOODIE PRO - DUAL HEATING Manual de usuario

ACP

ACP OMNISTAND Manual de usuario

Scarlett

Scarlett VitaSpa SC-CA304PS11 Manual de usuario

tanning essentials Classic Guía de instalación

Manuales populares de Producto de cuidado personal de otras marcas