T&D TR7 Series Instrucciones de instalación

» We shall not guarantee the unit's operation if it has been connected to

a PC using a USB hub or a USB extension cable.

» Do not insert any foreign objects into any of the units' jacks.

» If the unit gets dirty, wipe it with a clean cloth.

» Make sure to remove dust and dirt from plugs of any cables.

» Battery terminals may provide insucient contact due to age or vibra-

tion. This may lead to data loss.

» Please note that this document has been written based on the presup-

position that details about contracts with an Internet provider, specic

network environments and the set-up of any other necessary equip-

ment to enable network connection has already been taken care of by

the User and that connection has been conrmed as workable. T&D

Corporation shall not be responsible for any damages which a contrac-

tor, a user or a third party may suer, whether direct or indirect, due

to the inability to communicate or use communication devices.

» Please be careful not to let a third party know of your registration

code. The registration code cannot be reissued or changed.

CAUTION Notices about Sensors

» Do not connect any sensor to the unit other than those specied by

T&D Corporation.

» Make sure to use sensors within the measurement range indicated in

the specications for that sensor.

» Do not connect the sensor to any data logger other than those speci-

ed by T&D Corporation.

» Do not expose the sensor to a strong impact. This may adversely aect

measurement accuracy and cause damage or malfunction.

» When the sensor is not to be used for a long period of time, please

store it at normal temperature and humidity.

» The included sensor is not water resistant. If the sensor gets wet,

immediately remove the sensor from the unit and wipe it with a clean

cloth as soon as possible. Then allow the sensor to dry in normal room

temperature before using it again.

» Do not use the sensor on the human body.

Temperature-Humidity Sensor

» If extremely severe temperature changes occur, it may result in large

errors in humidity measurement. Once the sensor's temperature

becomes stable, the measurements will return to normal.

» The temperature-humidity sensors will with normal use experience

losses in precision and sensitivity over time due to degradation. If the

sensor is being used in an unsuitable environment (smoky or dusty

places) it may be necessary to change the sensor sooner.

» When using the sensor in an environment where the humidity is under

30 %RH, the measurements may sometimes uctuate. This is not abnor-

mal.

» Do not expose to condensation, dampness, corrosive gases, or organic

solvents.

Thermocouple Sensors

» We do not handle the sale of Thermocouple sensors. Please prepare a

commercially available sensor.

Safety Precautions and Instructions

The following items should be strictly obeyed for the safe usage

of this product, and for protecting yourself and other people

from bodily harm and/or damage to property.

Explanation of Symbols

DANGER

These entries are actions that absolutely under no

circumstance should be taken. The taking of such an

action may cause serious personal physical damage or

death.

CAUTION These entries are actions that if taken may lead to

physical injury or damage to persons or things.

Denotes an

important warning

or caution.

Denotes a

forbidden action.

Denotes an action

that should not be

carried out.

DANGER To Prevent Serious Accidents

Do not disassemble, repair or modify the unit and/or accessories.

Do not use the unit in any environment that is exposed to chemi-

cals and harmful gases. Doing so may cause corrosion and/or

other danger to the unit. Also, coming in contact with hazardous

substances may cause bodily harm to the user or people nearby.

This product is not water resistant. If water or a foreign object

enters the case, immediately remove batteries and stop using it.

Do not touch the unit or AC adaptor during thunder and lightning,

as this may cause electrocution.

Do not handle the unit, remove batteries or cables with wet hands.

This product has been designed for private and/or industrial use

only. It should not be used in situations where strict safety precau-

tions are necessary such as with medical equipment, or in systems

directly or indirectly connected with human life or well-being.

Do not drop or expose the unit to a strong impact.

Do not cut or process the cords for the communication cables.

Also, do not twist, pull on or swing any of the cords.

To prevent damage to the unit from static electricity, remove static

electricity from your body by touching metal around you (such as

a door knob and window frame) before touching the unit.

Place and store the unit and accessories out of the reach of chil-

dren.

We are not responsible for any damage, malfunction or trouble,

whether direct or indirect, caused by the use of our product.

Do not use any battery, sensor, or cable other than those specied

by T&D Corporation.

Do not put anything on top of the cable or the unit. This may

cause overheating.

Do not disconnect the USB cable during USB communication. Do-

ing so may cause adverse eects to the unit and/or PC.

Make sure that sensor and cable plugs are all inserted fully, so as

not to cause an improper connection. Also, when unplugging the

cable from the unit, do not pull the cord, but hold the connector to

disconnect.

If the unit produces heat, emits smoke or a strange smell, or

makes unusual noise, immediately remove the batteries and stop

using it. Also, unplug the unit from the PC.

If the unit is not to be used for a long period of time, remove bat-

teries. Leaving batteries inside the unit may cause battery leakage

and malfunction. Install new batteries when starting or re-starting

to use a unit.

For TR-75nw / TR-75wb: Ch.1 and Ch.2 terminals are NOT electri-

cally isolated from each other. Do not attach non-isolated thermo-

couple sensors to objects connected to a live voltage. This may

cause a short circuit or an electrical shock.

CAUTION

Do not place or store in the following areas:

» Areas exposed to direct sunlight

» Areas subject to direct ames or heaters, as well as areas in which hot

air accumulates and creates extremely high temperatures

» Areas exposed to static electricity

» Areas exposed to strong magnetic elds

» Areas exposed to water leakage

» Areas subject to condensation or wet areas

» Areas exposed to excessive vibration

» Areas exposed to excessive smoke, dust or dirt.

CAUTION Other Precautions

» Use the unit in the specied operating environment. Do not use it for

any purpose other than for which it was designed.

» Condensation may occur inside the case when a unit is moved from

one environment to another where there is a great dierence in tem-

perature.

» Do not use the unit in wet areas or places exposed to water such as

bathroom.

» When connecting the unit to your PC, make sure to follow all warnings

and directions from your computer manufacturer.

TR7 Series Thermo Recorder TR-71nw / 72nw / 75nw / TR-75wb

Please Read First

Package Contents

TR-71nw Temperature 2ch

Data Logger Temperature Sensor

TR-0106 x 2

AA Alkaline Battery

(LR6) x 2

USB Mini-B Cable

(US-15C)

Manual Set

(Warranty Included)

Registration

Code Label

TR-72nw Temperature 1ch, Humidity 1ch

Data Logger Temperature-

Humidity Sensor

THA-3001

AA Alkaline Battery

(LR6) x 2

USB Mini-B Cable

(US-15C)

Manual Set

(Warranty Included)

Registration

Code Label

TR-72nw-S Temperature 1ch, Humidity 1ch

(High-Precision Type)

Data Logger

High Precision

Temperature-Humidity

Sensor SHA-3151

AA Alkaline Battery

(LR6) x 2

USB Mini-B Cable

(US-15C)

Manual Set

(Warranty Included)

Registration

Code Label

TR-75nw / TR-75wb Thermocouple (K, J, T, E, S, R) Temperature 2ch

Data Logger AA Alkaline Battery

(LR6) x 2

USB Mini-B Cable

(US-15C)

Manual Set

(Warranty Included)

Registration Code

Label

* Please prepare a thermocouple separately. T&D does not handle the sale of thermocouple sensors.

Getting Logger Ready for Installation

Battery Installation & Sensor Connection

Battery

Make sure to use new

batteries (including for

replacement) and insert

in the correct direction.

TR-71nw TR-72nw

TR-72nw-S

About TR-71nw Internal Sensor

Channel 1 has an internal temperature sensor. When an external sensor is not connected, the

internal sensor will be used.

About TR-75nw / TR-75wb Input Terminal

When connecting thermocouple wires to the input terminal, make sure that the positive and

negative connections are in the proper order. If the polarity is incorrect, changes in tempera-

ture will be reversed (when the real temperature increases, the measured temperature will

decrease).

Wiring Connections

Connect and disconnect the thermocouple wire from the hole while

pressing the input terminal button with a screwdriver or other such tool.

Do not try to pull out the wire without pressing the button.

Compatible Wires

Single wire: 0.32 to 0.65 (AWG 28-22)

Twisted wire: 0.08 to 0.32 (AWG 28-22)

Diameter: 0.12 or more

Strip length: 9 to 10

Strip

Button

Using GND

If measurements are unstable while using external power (USB or PoE), connect to the GND terminal.

»See the Introductory Manual for how to set and check thermocouple sensor type for TR-75nw / TR-75wb.

The Introductory Manual also explains operations using the operation buttons.

Part Names

TR-75wb

(Wireless LAN)

TR-71nw / 72nw / 75nw

(Wired LAN)

TR-71nw / TR-72nw /

TR-72nw-S TR-75nw / TR-75wb

Operation Buttons Battery Cover USB Port

Sensor Jack

Channel 1

Sensor Jack

Channel 2

(TR-71nw only)

Power Button

Thermocouple

Input Terminal Ethernet Port (LAN)

PoE LED

turns ON when running

on external power.

LINK LED

ashes during network

communication.

TR-71nw / TR-72nw / TR-72nw-S / TR-75nw / TR-75wb - Specications

TR-71nw TR-72nw TR-72nw-S TR-75nw TR-75wb

Measurement Channels Temperature 2ch Temperature 1ch, Humidity 1ch Temperature 1ch, Humidity 1ch Temperature 2ch

Sensor Thermistor Thermistor Polymer Resistance Thermistor Polymer Resistance Thermocouple: Type K, J, T, E, S, R (*1)

Measurement Units °C,°F °C,°F %RH °C,°F %RH °C,°F

Measure-

ment Range

Internal Sensor

10 to 60°C (*2) - - - - -

External Sensor

40 to 110°C (Supplied Sensor)

60 to 155°C (Optional

Sensor:Fluoropolymer Coated

Type)

0 to 55°C 10 to 95 %RH

25 to 70°C 0 to 99 %RH (*3)

Type K :

199 to 1370°C

Type J :

199 to 1200°C

Type T :

199 to 400°C

Type E :

199 to 1000°C

Type S :

50 to 1760°C

Type R :

50 to 1760°C

Accuracy

Avg. ±0.3°C

20 to 80°C

Avg. ±0.5°C

40 to

20°C, 80 to 110°C

±0.5°C ±5 %RH

at 25°C, 50 %RH

±0.3°C

at 10 to 40°C

±0.5°C

at all other temperatures

±2.5 %RH

at 15 to 35°C, 30 to 80 %RH

Thermocouple Measurement

(Sensor inaccuracies not included)

Type K, J, T, E : ±(0.5°C + 0.3 % of reading)

100°C or above

Type S, R : ±(1.5°C + 0.3 % of reading)

at 100°C or above

Cold Junction Compensation

±0.5°C

at 10 to 40°C

±0.8°C

other temperatures within the operating environment of

the logger

Measurement Resolution 0.1°C 0.1°C 1 %RH 0.1°C 0.1 %RH Type K, J, T, E: 0.1°C, Type S, R: Approx. 0.2°C

Responsiveness

Thermal Time Constant:

Approx. 75 sec.

Response Time (90%):

Approx. 190 sec.

Response Time (90%): Approx. 7 min. Response Time (90%): Approx. 7 min. -

Logging Capacity 8,000 data sets (One data set consists of readings for all channels in that type of unit.)

Recording Interval Select from 15 choices: 1, 2, 5, 10, 15, 20, 30 sec. or 1, 2, 5, 10, 15, 20, 30, 60 min.

Recording Mode Endless (Overwrite oldest data when capacity is full) / One Time (Stop recording when capacity is full)

Auto-upload Interval Select from 15 choices: OFF (No auto-upload), 1, 2, 5, 10, 15, 20, 30 min. or 1, 2, 3, 4, 6, 12, 24 hrs.

Communication Interfaces

Wired LAN Communication

100BASE-TX/10BASE-T (RJ45 Connector)

Protocol : HTTP(*5), DHCP, DNS

USB Communication

USB 2.0 (Mini-B connector)

Wireless LAN Communication

IEEE 802.11b/g/n (2.4GHz only)

Security (*4): WEP (64bit/128bit),

WPA-PSK(TKIP), WPA2-PSK(AES)

WPS 2.0 : Push Button Conguration

Protocol : HTTP(*5), DHCP, DNS

Bluetooth Communication

Bluetooth 4.2 (Bluetooth low energy)

USB Communication

USB 2.0 (Mini-B connector)

Power (*6) Battery: AA Alkaline LR6 x 2, AA Ni-MH x 2

External: USB Bus 5V 200mA, AC Adaptor AD

05A2 or AD

05C2, PoE IEEE 802.3af

Battery:

AA Alkaline LR6 x 2, AA Ni-MH x 2

External:

USB Bus 5V 200mA,

AC Adaptor AD

05A2 or AD

05C2

Battery Life (*7) Approx. 10 days to 1.5 years (*9) Approx. 10 days to 1

year (*9) Approx. 10 days to 1 year (*8)(*9)

Dimensions H 58 mm x W 78 mm x D 26 mm

Weight Approx. 55 g

Operating Environment Temperature:

10 to 60°C (*10), Humidity: 90 %RH or less (no condensation)

Temperature:

10 to 60°C

Humidity: 90 %RH or less (no con-

densation)

Software

PC Software (Windows) (*11)

TR7 for Windows, T&D Graph, T&D Data Server

Mobile Application (iOS, Android)

T&D Thermo

(For compatible OS versions, please refer to the Software page of our website at tandd.com/software/)

*1: Compatible wire sizes are as follows. Single Wire : 0.32 to Ø 0.65 (AWG 28 - 22), Twisted Wire : 0.08 to 0.32 (AWG 28 - 22), 0.12 or more in diameter, Stripping Length : 9 to 10

*2: When Auto Upload is used frequently, the measurement of the internal sensor may rise by around 0.3°C .

When using external power, the data logger itself generates heat and the internal sensor will report a temperature much higher than ambient; we recommend using an external temperature sensor in this case.

*3: When continually used in environments with temperatures above 60°C, accuracy of humidity measurements will decrease over time. Also, humidity cannot be measured at temperatures below -20°C.

*4: If you wish to use the WPS feature, set the security type of the wireless LAN access point to "WPA2-PSK(AES)" or "None".

*5: HTTP client. Proxy supported.

*6: When using external power, the internal temperature of the logger rises.

*7: Battery life is highly dependant on the Auto-upload interval; at 1 min will give 10 days of usage, and at 12 hours or more will yield the maximum lifetime. Other inuential factors include LAN environment, ambient temperature,

recording interval, and battery performance. All estimates are based on operations carried out with a new battery and are in no way a guarantee of actual battery life.

*8: Shows the estimated battery life with Bluetooth ON. It will be 1.2 times longer with Bluetooth OFF.

*9: Shows the estimated battery life with Auto-Upload ON.

*10: -10 to 45°C when using external power (TR-7nw only).

*11: For installation, it is necessary to have Administrator (Computer Administrator) rights.

The specications listed above are subject to change without notice.

Important Notices and Disclaimers

In order to properly use this product, please carefully read all documents that accompany the product before using.

» All rights of the attached documents belong to T&D Corporation. It is prohibited to use, duplicate and/or arrange a part or whole of the attached documents without the permission of T&D Corporation.

» Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

» Google, Android, and Google Play are trademarks or registered trademarks of Google Inc.

» Apple and App Store are trademarks or registered trademarks of Apple, Inc. in the U.S. and other countries.

» The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by T&D Corporation is under license.

» All registered trademarks, company names, product names and logos mentioned herein or for products being used are the property of T&D Corporation or of their respective owners.

» Specications, design and other contents outlined in the attached documents are subject to change without notice.

» Please follow the safety precautions outlined in the attached documents carefully. We cannot guarantee nor are we responsible for safety if this product is used in any manner other than was intended.

» On-screen messages in the attached documents may vary slightly from the actual messages.

» Please notify the shop where you purchased this product or T&D Corporation of any mistakes, errors or unclear explanations in the attached documents.

» T&D Corporation accepts no responsibility for any damage or loss of income caused by the use of our product.